How Premiere Achieves Motion Blur Urgent !!

Method 1: Dot and add blur effects!

Due to the lack of PR plugins, this section can be done with AAE! It's as simple as adding a special effect and watching the effect.

Add keyframes within the range of motion blur you want.

Click on the "Effect Controls" tab in the Source Footage Monitor, and a Gaussian blur drop-down menu will appear, click to open.

For example, if this segment has a total of 10 seconds, pause at the first second, add keyframes, and adjust the "blur level" of Gaussian blur, not to the maximum first, such as 3.

Then pause at the third second and add keyframes, as above, this time to 5, and so on until the end of 10 seconds, you can adjust the blurring of the keyframes in the middle to make it even more.

2.In the Look panel, click on the Filters section to add a Radiant Blur, Rotation Blur, Motion Blur, or Lens Blur (Flare Effect) effect.

3.In the "Overlay Footage" panel, click "Watermark Removal", select the watermark removal area and time period, and select "Remove Method" as "Blur" on the right side of the list, or you can add a blur effect to **.

1. Make a blur effect.

After editing**, in the "Filter" column of "Picture Style", double-click the "Lens Blur (Flare Effect)" option, and in the pop-up dialog box, set the time period for the blur effect to be applied according to your personal needs.

2. Set the blur effect flexibly.

On the right side of the style list, you can set the blur effect flexibly such as "Blur Degree" and "Soft Transition", and click the "Confirm Modification" button after adjustment.

On the timeline, on the ** used, click on the right --- field setting --- select "Non-interlaced (progressive)", and after rendering, the jitter will be much reduced. But it can't be solved fundamentally.

Also, it can't be too big! The bigger it is, the heavier the jitter. As long as it's enough for special effects, it's fine.

We generally use 720*576 pixels, and the resolution is 180. That's it. If you do the first exercise, you may need to be a little bigger, but not too big.

Add the blur effect you want in the effects bar on the left.

There are a lot of blurry effects in the special effects block, try more.

It's going to take a lot of effort to figure out what you need.

Because the bitrate is too low when you rotate. Can be turned up. There is an output configuration when converting, and there is a bit rate in it, so let's change it to a higher level.

There are many types of blurring, and you can set the level of blur.

Drag the desired blur effect (e.g. Lens Blur) onto the desired clip, and set a keyframe at the beginning to 0 or lower;

At the end, set another keyframe, setting the blur level to maximum or large.

Render and see the result.

There are 2 options at the top of the material preview box, and the one on the right is.

You can set Motion, Rotation, Transparency, Blur, Zoom In, Zoom Out, and so on.

I sent you a link to a set of tutorials.

Operating Equipment: Dell Computer.

Operating system: win10

Operating software: premiere 2017

4. Then click on the effect control above, and select an oval here.

5. Then add where you need to blur locally.

6. Adjust the appropriate fuzzy parameters.

4. Then click on the effect control above, select the shape below the Gaussian blur, you can choose an ellipse, a rectangle, or you can use a pen to customize the shape of the painting, here you can choose an ellipse.

5. Then add where you need to blur locally.

6. Adjust the appropriate fuzzy parameters.

Open**, copy a layer, filter - blur Gaussian blur, radius 2 to 3 pixels, then Zen do a copy layer, and then blur until you want the effect. Then animate the word. Of course, you can also make the process of copying the picture pin-out layer - blurring into an action, and then the ** action is OK.