How three wireless routers are wirelessly bridged

One uses the main port to access, and the other uses the LAN port to access.

The last bit of the LAN port IP is set to be different, and all LAN ports are used.

The router itself must be supported by its own hardware.

The two wireless routers are bridged, and the one connected to the broadband Internet is called: the main router; Call the other router: the secondary router.

Step 1: Plug in the Swift Router and connect the computer to any of the LAN (1 2 3 4) interfaces of the Swift Router with a network cable.

2. Open the browser on the computer, type: in the browser, enter the login page, and enter the "login password".

3. On the settings page of the Swift Router, click "Advanced Settings", "Wireless Settings", "WDS Wireless Bridge".

4. In the "WDS Networking Wizard" page, click Next.

5. The Swift Router will automatically scan the nearby wireless signals, and select the wireless name of the main router in the scanning result.

<>7. Set the wireless name and wireless password of the secondary router.

<>9. Check whether there is a problem with the parameters of the wireless bridge in the page, if they are correct, click the "Finish" button, and the wireless bridge will be automatically configured.

Here's how:

The first router is set up normally and can be connected to the external network.

Second router:

The third router also changes the LAN port address and disables the DHCP function.

After setting up the router, you can connect the LAN port of the router in series with a network cable.

Big brother, have you made a mistake, of course you need a route to connect to the external network! Such questions have to be asked, it is really recommended that A is the main route, connected to the external network, and there is no need to open WDS to just transmit wireless. B turns on WDS to connect to A's wireless, and C turns on WDS to connect A or B, either.

It's as simple as that, you know!?

A Mutual MAC is required to connect to the bridge.

This one, it's just one more step to bind the mac, it's all the same.

If the connection between A-B-C and WDS is not stable, it is recommended that A connect B and A to C

First, to do wireless bridging, generally need a router or wireless AP to have this function, in the general home wireless router, some call this wireless bridging, some called WDS, etc., and the W311R router I use is called WDS;

Second, the two routers are powered on, it is recommended to set up through a wired connection router, because the factory default gateway of the two routers is, so first modify the gateway of the main route to, log in to the router web interface, after setting up PPPOE dialing, you can access the Internet through the main router, set and modify the SSID (wireless network service identifier) of the router to test1, and set the SSID of the other router to test2 in advance, and then select "WDS settings" - there are three modes to choose from, There are three types: lazy mode, bridge mode, and repeater mode, and after using lazy mode, you can save & restart the route; After using the bridge mode, the wireless signal is turned off, and the wireless network card cannot scan the signal of test1, this application is used to bridge two wired networks, not used in this example, and will not be described in detail; Use the repeater mode to start the scan, scan the signal with SSID as test2, add it, save & restart the route;

3. Set up another route (defined as a slave route), also use the WDS function to set, then the WDS of the main route can be LAZY and repeater mode, and the slave route can only choose the repeater relay mode, turn on scanning, find the signal of test1, add and save, and then shut down the DHCP server from the router, save & restart the router;

4. At this time, connect to the slave router with wireless or wired, and after the IP address is successfully obtained automatically, the connectivity will be detected and the main router gateway will be pinged. Try it, it can ping, then there is no problem, ping can't work, check the configuration, or see if the wireless encryption method is equal, just open the web page and start surfing!!

PS: When doing wireless bridging, wireless encryption can only be done in WEP mode. Of course, both must support wireless bridging.

Note: The location of the two routers should also be carefully studied, and strive to achieve the maximum coverage and the best signal strength.

1. First of all, the main router is always normal, so that it can connect to the Internet normally;

2. Open the browser to log in to the secondary router settings page, take the TPLink WR886 router settings as an example, click Wireless Settings - Basic Settings, click to check to turn on WDS, and click Save;

4. Select the encryption method of the main router, enter the password of the main router, and click Save;

5. Click Restart and wait for it to finish.

Friend, according to your description, I understand that you mean to have two wireless routers communicate with each other, i.e., router bridge communication.

First of all, the wireless router must support the wireless routing bridging function, and when buying a router, you must see if the router you buy supports this function. Second, the two bridged routers must be within each other's valid range.

The TP-Link 340G+ I use at home can bridge two wireless routers. I configured it as follows:

Wireless Router A:

Set the address of the LAN port to .

Connect to ADSL, set PPPoE as normal, and enable DHCP.

SSID is set to ABC

Turn on the wireless bridging function and enter the MAC address of wireless router B in the MAC address table of the bridge AP 22-22-22-22-22

Save the reboot. Wireless Router B:

Set the address of the LAN port to .

The WAN port and LAN port are not connected, and the DHCP function is disabled.

SSID is set to ABC

Turn on the wireless bridging function and enter the MAC address of wireless router A 11-11-11-11-11-11 in the AP MAC address table

Save the reboot. In addition to the above configurations, the other configurations of the wireless parameters of the two wireless routers are the same, such as the wireless encryption password of the two wireless routers must be the same, etc., but after the bridge function is turned on at 340G+, the wireless encryption can only support up to 128-bit WEP encryption. You can choose another router that supports bridging and can use WPA or a more secure encryption method when bridging.

If both wireless routers support 5G, use a 5G bridge. Before setting, there is no need (and can't) connect network cables between the primary and secondary routers; Dual-band routers cannot be bridged with 5G at the same time; Wireless bridging only needs to be set up on the secondary router, and the following operation instructions are carried out on the secondary router; Here's how:

1. First of all, make sure that there is a main router in the house that is functioning properly. If you have a router set up at home, skip to step 2 directly. If you don't set up the main router, there are two ways to set up the router, computer, it doesn't matter if you don't have a computer, you can also set up a router with a mobile phone.

2. Turn on your computer again and set up the router to dial up the Internet. Open the browser, enter the old router is to enter the general router at the bottom of the back of the management page address. Enter to set an administrator password.

3. Select broadband dial-up Internet access. Then enter the broadband account and password, and finally set the wifi name and password, and remember it yourself. Then restart your router. Wait a few minutes for the router to go online normally.

4. After connecting, enter the address of the management page in the browser of the mobile phone, and the management page is also set to the same password to remember. Click Skip on the dial-up interface, and the Get IP is set to automatically obtain or skip as well.

5. Enter the main management page of the router, and there is an application at the bottom, enter to find the wireless bridge. Click in. Then scan for wireless signals around you. Choose your own primary router wirelessly. Then enter the wifi password of the main router.

6. Next, the router will let you set the wifi name and password of the secondary router. It can be the same as the primary route or different. Then restart your router. Wait a minute or two.

Notes:

1. When setting up the bridge, you don't need to set WDS on both routers, but just set it on the second router.

2. The DHCP service of the second router needs to be turned off, some tutorials do not emphasize it in particular, and many people do not set this point.

3. Computers or other access devices do not need to emphasize the setting of static IP. When setting up a bridging, regardless of the brand and model of the router, it only needs to have the bridging (WDS) function, and it can be successfully set up according to this method.

Step 2: Open the phone settings, click [WLAN], find the name of the secondary router, click it, and click the small arrow icon behind it to view the gateway;

Step 4: Click [Skip Wizard], click [Advanced Settings], select [Wireless Settings], and click [WDS Wireless Bridge];

Step 5: Click [Next] to check if there is a wireless name of the main router, if not, click [Manually add the main router], enter the name and password of the main router, and click [Next].

Step 6: Set the name and password of the secondary router, click [Next], then click [Next], and then click [Finish].

Step 7: Open the phone settings, click [WLAN], tap the set wireless network, enter the wireless network password, and click [Connect].

Wireless bridging generally refers to:

Wireless routers.

are wirelessly connected to extend.

Network coverage. This is generally achieved by turning on the WDS that comes with the wireless router; In your case, the wireless signal is very weak, and you can only connect to a wireless router through wired, which is not a WDS bridge in the general sense, but a downlink or parallel.

Router two ways:

Downlink method: will.

One section of the network cable is connected.

Connect to the Internet. The LAN port of the router (740N), the other end is connected to the WAN (340G+) port of the router, and then the 340G+ WAN port is set.

is a dynamic address.

If you have 740n

DHCP on), or directly.

Static address. As; ,,dns

The server is the same as 740n), 340g+

The LAN address has been changed to prevent conflict with the above 740N, and the DHCP of 340G+ is enabled

When setting up 340G+, do not connect the network cable first, and then connect it after setting it up, so as not to cause network conflicts.

In this way, the connection uses the ** of the 740n router and the ** of the 340G+ router, two network segments.

Parallel connection mode: The network cable is connected to the 340G+ LAN port, which is to treat 340G+ as it.

The switch also changed the LAN address of 340G+ first, turned off its DHCP service, and turned on wireless service. , at this point, wireless access.

340g+.

The terminal uses 740N DHCP, ** is;

Both of the above can be achieved.

Your request. Follow-up, if you use the downlink method to set the 340G+ WAN port as a dynamic IP, when you set it inside.

What should be filled in the hostname, fill in 740n.

MAC address.

When setting up a bridge, you don't need to set it up on both routers, you just need to set it up on the second router. The details are as follows:

First, set up the main router to be able to access the Internet. There should be no problem with this, set the access type according to the wizard, fill in the username and password given by the operator, etc.

2. Set the wireless settings of the main router, and then set the wireless network name, password, etc. That is, you should remember the name of your network, including the password, save and restart the router. The network name and network password will be used on the secondary router later.

3. Log in to the secondary router and set an IP address in the LAN port settings.

Fourth, the wireless settings of the secondary router also give a name to the wireless network, and you can recognize and distinguish it from the main router. The channel settings should be the same as those of the main router, and you need to click and tick in the box before opening. Tick to turn it on, then click Scan, you can search for nearby wireless networks, find the name of the main router you just now, click to connect, and enter the password.

After the restart, the status display is successful, and all settings are complete. This is the bridge between two routers, if there is a third or more routers, add them in the same way as above.

Bridging between the same brand is the most convenient and there will be no conflicts; Specifically, take a look at the manual, or call the manufacturer**, good luck!

Dear users, hello:

First router:

1.First, log in to the router that is connected to the Broadband Modem.

2.Set the SSID number and Channel in Wireless Settings - Basic Settings, and set the fixed channel number.

3.Set the wireless signal encryption information in the Wireless Settings - Wireless Security Settings to record the SSID, channel, and encryption settings of the wireless router after setting.

Second router:

1.Log in to the second wireless router that needs to be bridged.

2.In the network parameters - LAN port setting, change the IP address to be different from the first router (to prevent IP address conflicts), for example, save, the router will automatically restart.

4.Select the SSID number of the first router in the list of scanned signals and click "Connect".

5.Set the channel to be the same as the first router channel. At the same time, set the encryption information to be the same as the first router, and click "Save".

6.Shut down the DHCP server. In the DHCP server, select Disable, save, and restart the router.

7.At this point, the first wireless router and the second wireless router have successfully established WDS.