Is it reasonable for a house with a construction area of 120 square meters and only three sets of ge

To judge the number of circuits of the floor heating pipeline, it is necessary to consider the form of heating, which should be calculated:

1. The construction area is 120 square meters, assuming that the public share is 20%, and the usable area is 120* square meters. Some locations are not in place, so the actual area of floor heating is calculated by 90%, and the actual floor heating area is 96 * square meters.

2. The density of floor heating laying is usually 20 cm apart, so the amount of pipes per square meter is 5 meters, but there are bends and repeated parts, under normal circumstances, the actual amount of pipes per square meter of floor heating is about meters. So the total amount of tubes used is meters.

3. According to the relevant specifications of floor heating stipulated by the state, the temperature of floor heating water supply shall not exceed 60, and the temperature difference between supply and return water shall be 10. Therefore, after calculating the thermal load, the single circuit of floor heating for central heating should not exceed 120 meters, and the single circuit of floor heating using household heating (such as using gas wall-hung boiler as a heat source) is not easy to exceed 80 meters.

4. Therefore, the number of loops is calculated as follows:

Central heating:. 3 circuits are not very qualified, it is better to divide into 4 circuits.

Household heating (gas wall-hung boiler): To set up 5 circuits.

Theoretically, the length of the pipe of each water separator belt is about 50-85 meters.

Depending on the region, the length of the pipeline may vary.

If it is the Northeast region, the pipeline is slightly longer, and the water separator is a little less.

Suggestion to lodge a complaint.

It's slower, it's a little colder, but that's okay. If you can afford it, you can consider adding a few more sets of geothermal pipes.

Summary. Electric underfloor heating heats the ground temperature when the power is turned on by means of a resistive heating element laid underground. When the heating element is energized, the operating temperature of the conductor is controlled below sixty-five degrees Celsius, and the operating temperature is transmitted above the ground through radiation as a heat dissipation surface, so that the surface temperature of the conductor can be raised and the room temperature can be maintained.

The electric floor heating structure includes a heating element, a thermostat, and ground accessories. Advantages: comfortable, no maintenance, single room can be controlled or closed, energy saving; No noise, no pollution, low energy consumption, does not occupy high-rise.

Disadvantages: It cannot cover the heat resistance of thick carpets, etc., and has certain requirements for electric capacity.

Hello, I am helping you to inquire about the relevant information and will reply to you immediately.

The 110-square-meter house has a geothermal system that normally requires six to eight geothermal pipes. Geothermal pipes are in rolls, with no seams in between, and a roll of Da Burn Cha is about 300 meters of Pihui Tomato. A circuit in a floor heating system is usually laid at 80 to 90 meters or 14 to 15 square meters, and a 110 square meter house is almost six to eight circuits.

Electric underfloor heating heats the ground temperature when the power is turned on by means of a resistive heating element laid underground. When the heating element is energized, the working temperature of the conductor is controlled below 65 degrees Celsius, and the working temperature is transmitted above the ground through radiation as a heat dissipation surface, so that the surface temperature of the conductor can be increased and the room temperature can be maintained. The electric floor heating structure includes a heating element, a thermostat, and ground accessories.

Advantages: comfortable, no maintenance, single room can be controlled or closed, energy saving; No noise, no pollution, low energy consumption, do not occupy high-rise. Cons:

It cannot cover the heat resistance of thick carpets, etc., and has certain requirements for electric capacity.

Hello dear, very happy for your question, under normal circumstances, 100 square meters of houses are required to install 5 groups of geothermal pipes, the installation of heat pipes are corresponding, normally a circuit only needs to be designed in 60 to 70 meters or so. When installing floor heating pipes, it is also necessary to determine according to the actual situation in the home, before installing floor heating, it is necessary to find a professional company to design pure bending guess, and the material of the floor heating pipe is also very important, it is necessary to choose the best geothermal pipe, so as to achieve the corresponding use effect, and the service life of the first geothermal pipe is also relatively long.