What should I do if my Chopard watch accidentally falls into the pool?

If you accidentally fall into the water, you can also salvage it in time, then dry it overnight, and finally take it to the place where the watch is repaired for repair.

Generally, a good water meter has the ability to bear pressure, and it will not enter the water if it falls into the water at a depth of 40 meters, so you don't have to be afraid.

Look at the first time should be taken out, and then the water should be dried, so that there is relatively no big problem, if it really doesn't work, it may be that there is water inside, so you can only open the inside.

This kind of watch generally needs to be dry and waterless in order to be used more normally, accidentally dropped into the pool, it is best to salvage it as soon as possible, find a professional master for maintenance, so that it is more conducive to prolong its service life.

If the Chopard watch accidentally falls into the pool, you should quickly release it and put it in a dry place to wait for the water in it to evaporate, if it does not affect the normal operation of the watch, it does not matter.

That's to salvage it yourself and inside, what if you can't do it, or buy a metal detector and borrow one, so you can find it.

If we accidentally fell into the pool, we should immediately take it out and clean it up in time.

There is no other way but to fish it by hand. You can also use magnets to Iriomote.

If you accidentally drop your watch in the pool, you should take it out immediately, blow dry the surface, and then open the cover to dry the inside.

When Xiaobang watch fell into the pool, of course, it was immediately fished out and wiped clean, and then sent to the acquisition watch repair center for maintenance.

You see if there's water mist in the glass, and if there's none, there's nothing.

If the watch falls into the water, you have to use that hair dryer to dry it, open the back case, and then dry it to see if the logo can be turned to see if it can be used.

If you can catch it, you can catch it, and if you can't catch it, you can't do it.

After taking it out, hurry up, well, dry it in the depths, and see if it's okay in general.

If it's just a drop, it doesn't matter, it's waterproof, but you must pay attention to drying it when you pull it up.

Method 1: If an ordinary mechanical watch is damp, you can wrap the watch tightly with several layers of toilet paper or flannel cloth that is easy to absorb moisture, put it at a distance of about 15 cm near a 40-watt light bulb, and bake it for about 30 minutes, and the moisture in the watch can be dissipated. Do not bake the watch close to the fire, so as not to deform the watch by heat.

Method 2: Put the surface face inward and the bottom shell outward, and wear it on the wrist, and the moisture can be eliminated after two hours. If the water ingress is serious, it needs to be sent to a professional maintenance master to wipe the oil to remove the moisture of the movement and avoid rust on the parts.

Method 3: Put the granular silicone into a closed container with the watch that has accumulated water, and after a few hours, take out the watch and the water will disappear. This method is simple and economical, and there is no damage to the accuracy and longevity of the watch.

(1) There is fogging in the watch glass, and there may be some times and sometimes not, especially when the temperature difference is large;

2) There are water droplets condensed in the watch glass;

3) A large number of water droplets can be seen on the glass and dial of the watch;

If you find that the watch is flooded, it is imperative to send the watch to the watch repair shop for drying as soon as possible, and if the water is serious, it is necessary to do oil washing. If you don't do it in time, then the water will make the steel parts in the watch movement embroidery, and the tiny clock parts usually need to be replaced once they rust, and the repair cost in the future will be very large, you must know that the damage to the watch by water is "catastrophic". In addition to the movement parts, long-term contact with water vapor will also cause discoloration, blistering and rust of the watch dial and watch hands.

Here, I would like to remind you that if it is a watch with repeated water ingress, you need to pay extra attention when wearing it.

Water in the watch is a more serious thing, especially some high-end mechanical watches, if not repaired in time, then the water will make the steel parts in the watch movement appear embroidery, tiny clock parts usually need to be replaced once rusty, the future repair cost will be very large, to know that the damage to the watch is "catastrophic". In addition to movement parts, long-term exposure to moisture can also cause discoloration, blistering and rust on the dial and hands of the watch.

Hello, glad to answer for you.

Method 1: Silica gel drying granules. If water enters the case, you can use a granular substance called silicone to put the watch in an airtight container with the waterlogged watch, and after a few hours, remove the watch and the water will disappear.

This method is simple and economical, and there is no damage to the accuracy and longevity of the watch. The silica gel that has been absorbed many times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used again and again.

Method 2: Bake with an electric light bulb. If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, and bake it at a distance of 15 cm from a 40-watt light bulb for about 30 minutes to eliminate the moisture.

Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating. (It is not recommended to use the above methods to deal with it, it is recommended to go to the after-sales center for maintenance).

Hello, the watch water generally has water mist or water droplets on the watch glass, and it will corrode the movement for a long time, resulting in inaccurate or non-time, so the earlier the watch water treatment time, the less damage to the movement, the recommended treatment methods are as follows:

Law. 1. Place the vent - dry the watch with a dry paper towel and then place it in a cool and dry vent for a few hours, and do not place the watch directly in the sun or dry, which is to prevent water mist from flowing into the movement.

Law. 2. Silicone drying - for the water inlet of the mechanical watch, you can use the granular substance of silica gel to absorb water, put the two in a closed container, and take it out after a few hours, and the water mist inside will be cleaned up; If it is a quartz point clock, you can take a few small pieces of calcium chloride, wrap them in gauze, and then open the electronic watch cover and seal it.

Law. 3. Wipe oil and remove rust - method 1 and method 2 can only clear a slight water mist, and for some more serious water ingress, these two work earlier, which is not enough for the rescue time of the movement, at this time it is best to find a professional watch repair center for ** maintenance, oil wiping treatment.

If the water ingress is not serious, you can wear the watch with the watch face inward and the bottom case facing outward, and wear it on the wrist backwards, and the water vapor can be eliminated after two hours. If the water ingress is severe, it is best to send it to the watch shop immediately to wipe the oil and sweep away the nutrients of the movement to prevent the parts from rusting.

Way. 3. Use granular silicone to put the watch on the wrist that has accumulated water into a tightly sealed utensil, and after a few hours, take the watch on the wrist, and the water will disappear. This method is simple and economical, and there is no damage to the accuracy and longevity of the watch. The silica gel that has absorbed water many times can be dried at 120 for several hours, and the water absorption experience is renewable, and it can be used again and again.

What to do if the watch gets water.

1.If the water ingress is not serious, but there is a layer of mist on the surface, you can use toilet paper or flannel cloth that is easy to absorb moisture to wrap the table tightly.

2.Then bake at a distance of 15 cm from a 40-watt light bulb for about 30 minutes.

3.If the water ingress is severe, it is best to send it to a watch store immediately to wipe the oil.

Take it to repair, water will cause rust on the parts, water will enter depending on your waterproof level, or whether the rubber ring is aging, is it steam or what?

There are generally three ways to enter the water in the watch, the watch is worn backwards, the desiccant is removed and the lamp is baked to remove the water, it may seem that the effect is not bad, but the fact is not satisfactory, those methods can only remove the water stains on the surface, and the water stains that penetrate into the movement can not be removed with certainty, and it is not too much to treat those small watches, but for those famous watches, if this method is adopted, I am afraid that it will be regretted in the future. If this method can be handled completely, then the repairer will not have to eat. It is recommended to send it to a professional repair point if it enters the water.

So what do you do with a Chopard watch?

1.The most important of the three defenses of a Chopard mechanical watch is its water-resistance. In a relatively humid environment, even without a mechanical watch, the watch can rust due to prolonged exposure to the movement and moisture.

The water-resistant protection of a mechanical watch mainly depends on the construction of the case and the robustness of the water-resistant gasket.

2. The maintenance of Chopard mechanical watches is very important, a person must understand waterproof watches, first of all, to understand the waterproof knowledge of mechanical watches.

The water ingress of the watch should be dealt with in time, otherwise the water ingress for too long will damage the internal parts of the watch, resulting in rust of the movement parts, and these parts are very sophisticated watch configurations. If the watch gets water, it is recommended that you take the watch to a service center immediately to avoid further damage to the watch.

Chopard watches into the water repair location in Shanghai Huangpu District Nanjing East Road Pedestrian Street Landmark 9th Floor Room 918, *** strap to gold is the most common, gold color has white and yellow (white gold, yellow gold and rose gold), in addition, the most high-end is made of platinum, such watches are the most luxurious and expensive watches men's watches.

1. Wear the watch backwards. You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours. If the water ingress is severe.

It is best to send it to the watch shop immediately to remove the water in the watch, because if there is too much water in the mechanical watch, there is no way to dry it in time by adsorbing it from the outside, or drying it.

2. The watch is a precision machine, whether the water into the watch has an impact on the watch accessories, this is not sure, it depends on whether the water into the watch is very serious, and how the waterproof of the watch is. If it is only the watch of the watch that is fogged, it is estimated that the water ingress of the watch is not serious. If it causes the watch to slow down, not to go or other problems, it is estimated that it will have an impact on the watch accessories.

Therefore, it is recommended to go to a professional watch repair center for testing, and the general inspection is free.

Chengdu after-sales service center is in Room 05, 24th Floor, Sichuan Aviation PlazaTELL: 028-62225432

The solution to the water in the watch and the fog on the mirror:

Wrap the watch tightly with several layers of toilet paper or flannel cloth that is easy to absorb moisture, and bake it under the light bulb for about 30 minutes to eliminate the water mist inside, but do not put it close to the light bulb or bake it directly, so as not to cause the surface to be deformed by heating.

Wear the surface inwards and the bottom case outwards on your wrist to remove the mist from the surface after a few hours.

If you have silicone, you can put the silicone and the watch in water into a closed container, and after a few hours, take the watch out again, and the water mist in the watch will disappear.

If the water ingress of the watch is serious, it is best to send it to a watch shop to wipe the oil and eliminate the water in the watch to avoid rust on the parts of the watch.

Note: In order to prolong the service life of the watch, you should try to avoid fog and water droplets in the waterproof watch, do not wear the watch when washing your face, bathing, swimming and other "hydrophilic" activities, do not be affected by water vapor and hot vapor, and pay more attention not to be exposed to rain on rainy days.

If you find that the watch is flooded, you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, put it about 15 cm near a 40-watt light bulb, and bake for about 40 minutes, and the water vapor in the watch can be eliminated. Do not bake the watch directly near the heat, so as not to deform the glass by heating. Because although there is no moisture on the dial, there may still be water in the movement, and the movement will rust and cause damage to the movement after a long time.

After the watch is flooded, it is recommended to find a professional repair outlet as soon as possible for the master to check and deal with it, which can reduce your unnecessary losses.

If the water is not serious, but there is a layer of fog in the watch glass, you can directly wear the watch on the wrist for two hours, it is recommended that the watch replace the waterproof ring once a year, so as not to lose the watch waterproof, when the watch is damp, the best way is to go to the watch repair shop to do testing and oil wiping, so that you can prevent serious rust and corrosion of the watch with less cost. If the movement is corroded, the watch will be scrapped and the loss will be great

There are generally three ways to enter the water in the watch, the watch is worn backwards, the desiccant is removed and the lamp is baked to remove the water, it may seem that the effect is not bad, but the fact is not satisfactory, those methods can only remove the water stains on the surface, and the water stains that penetrate into the movement can not be removed with certainty, and it is not too much to treat those small watches, but for those famous watches, if this method is adopted, I am afraid that it will be regretted in the future. If this method can be handled completely, then the repairer will not have to eat. It is recommended to send the water to a professional maintenance point.

Chopard watch water after-sales maintenance location in Shanghai Xuhui District Hongqiao Road No. 1 Grand Gateway Center 1 7th Floor Room 707, the professional way is to remove the strap for cleaning, the use of ultrasonic cleaning machine, the cleaning liquid is added to the cleaning spirit, depending on the degree of dirt, serious dirt to do a few more cleaning, and then rinse with clean water, electric heating fan drying.