What should I pay attention to when installing aluminum plastic panels?

The precautions for the installation of aluminum-plastic panels are:

1. Aluminum-plastic panels should be stored or installed in a dry and ventilated place in an appropriate way to avoid water accumulation, and the ambient temperature should not be higher than 70. Avoid installation in abnormal environments, such as smoke, sand, radiation, harmful gases and chemicals.

2. Aluminum-plastic panels need to be placed flat during transportation or storage. When handling, the 4 sides of the board must be lifted at the same time, and do not drag unilaterally to avoid scratching the board surface.

3. When slotting with a slotting machine or gong machine, a round head or 90 should be used. The V-shaped flat-nose saw blade or milling cutter is grooved, leaving a thick plastic core board to bend the edge along with the panel to increase strength and toughness and prevent hydrogenation of the aluminum sheet. Sharp corners or cuts that hurt the aluminum panels or leave too thick plastic can cause the aluminum plate to break or the paint film to burst when the edge is bent.

4. When bending the edge, it is necessary to use uniform force, form it at one time, and do not bend it repeatedly, otherwise the aluminum panel will break.

5. In order to maintain the flatness of the aluminum-plastic panel and enhance its wind resistance, the aluminum-composite panel needs to be lined with a skeleton and pasted with glue and the plate after bending.

6. When used for the decoration of curved surfaces, bending equipment should be used to bend the aluminum-plastic panel, and slowly exert force to make the board gradually reach the required curved surface, and do not do it in one step. The bending radius should be greater than 30cm.

7. Install the aluminum-plastic panel on the same plane in the same process direction, otherwise it may cause visual difference.

8. The protective film should be torn off within 45 days after the installation of the aluminum-plastic panel, otherwise, the protective film will age due to long-term exposure to the sun and may cause glue residue when the film is torn.

9. The interior wall panel should be used indoors, and should not be installed outdoors to ensure its service life.

10. If there is pollution on the surface of the board during construction or use, it can be gently cleaned with neutral detergent or alcohol, and strong acid and alkaline detergent should not be used to clean it.

Skeleton aluminum square copper or aluminum gusset plate, glue with 995 structural adhesive. Don't use wooden boards to add all-purpose glue, this kind of two-year quasi-drop.

The skeleton is made of aluminum square tube, and the glue should be glued well.

Why ask such questions anonymously?

Aluminum-plastic panel is a new type of indoor and outdoor decoration materials that have just emerged in China, at present, there are many brands on the market, and the quality of the products is uneven; Because of its special structure, it is generally difficult for consumers to identify the intrinsic quality of the product, so we have the responsibility to remind consumers to pay attention to the following identification methods when purchasing and using aluminum-plastic panels:

1) See whether the surface of the aluminum-plastic panel is smooth and smooth, without ripples, bubbling, shelter points and scratches.

2) Measure whether the aluminum-plastic panel meets the international requirements, the interior wall panel is 3mm, and the external wall panel is 4mm

3) Fold the corner of the aluminum-plastic panel, which is easy to break is not PE material or doping.

4) The intermediate material of burned aluminum-plastic panel, the real PE is completely burned, and the doping makes the fake impurities after combustion.

5) When the planing groove is bent, see if the front is broken.

6) Drop butanone to identify the fluorocarbon coating of the exterior wall panel, drop to identify the coating of the interior wall panel, wipe off the reagent after 5 minutes to see if the bottom is exposed.

Installation Notes]:

1) Protective performance of the protective film The protective film is composed of black and white double-layer polyethylene. During installation, do not peel off the protective film to protect the surface of the board from being scratched or sticking to the mud. Under normal climatic conditions, the protective film is removed within six months, glue transfer and other damage to the plate will not occur.

Of course, it is best to tear off the protective film in time after construction.

2) The coating direction will cause a slight color difference When installing the aluminum-plastic panels of metallic color, glitter color and stone grain series, be sure to install them in the direction marked on the protective film, otherwise there will be color difference due to inconsistent installation directions.

3) Plasticizers can cause gloss differences Do not stick PVC tape, polyurethane sealant and improved silicone on the protective film of the aluminum-plastic brigade resistant board, because the plasticizers contained in these materials will penetrate the protective film and cause changes in the gloss of the coating.

Nowadays, there are many wall decoration materials on the market, such as: aluminum composite panel is one of them. So the question is, do you know how to install aluminum-composite panels? What are the properties of aluminum-composite panels? If you are interested in aluminum-plastic panels, you may wish to follow me to find out.

1.Base leveling: Before installing aluminum-plastic panels, the first thing to do is to smooth the original wall foundation.

2.Springline: The second is the springline, the main purpose of which is to accurately control the elevation control line and keel layout line.

3.Determine the keel position line: determine the size of the ceiling skeleton according to the specifications of the aluminum-plastic panel and the ceiling area. When leaving edges around the perimeter, the dimensions must be symmetrical, and the determined keel position line is drawn on the top of the elevation line.

4.Installation of wooden keel: the wall is perforated and the wooden tenon is fixed. Normally, the wooden keel selected is mainly 20*30, with a spacing of 400 or 600.

5.Installation of the base board: The next step is to fix the multi-layer board and blockboard, and the prerequisite must be on the wooden keel foundation or light steel keel.

6.Install the aluminum-composite panel: The back of the aluminum-composite panel is coated with glue and wait for 10-15 minutes to put on the board.

What are the properties of aluminum-plastic panels?

1.The material is easy to process.

The weight of the aluminum-plastic panel is only kilograms, so it can reduce the damage caused by the earthquake, and it is easy to handle and construct, only simple tools can be used to complete cutting, planing, bending and other shapes, and at the same time can make various changes, which has the advantages of easy installation and reduced construction costs.

2.Excellent fire performance.

In addition, the aluminum-plastic panel is mainly made of flame-retardant PE plastic core material, and the two sides are aluminum layers. Therefore, it is a good fireproof material, and at the same time, it meets the fire resistance needs in construction.

3.Impact resistance.

In addition, aluminum-plastic panels also have the advantages of high toughness and strong impact resistance, even if they are used in areas with large wind and sand, there will never be any damage.

Summary: After reading the above introduction, I believe you have a further understanding of how to install aluminum-plastic panels. If you need to know more about it, please continue to ******, and more exciting content will be presented to you in the future.

At present, the installation method of aluminum-plastic panel is mainly glued and glued, and dry hanging. There are many other installation methods, such as open installation, which basically avoid glue contamination. The indoor construction method of aluminum-plastic panel is as follows:

1. Plane paving method of wall and ceiling. This method of construction is the simplest, but it adds the amount of board and glue to the construction cost. 2. The frame binding method is a little more complicated.

3. Aluminum-plastic panels are installed indoors for specific aluminium alloy profiles. This installation method is the most convenient, fast and low-cost installation method for indoor wall installation of aluminum-plastic panels. There are a lot of them, which are generally cut with a cutting machine, and there are also diagonal ones.

1. Grassroots leveling. Flatten the original wall surface.

2. Install a wooden keel. Punch holes on the first face of the wall, and then fix it with wooden tenon, generally with 20*30 wooden keel or light steel keel (wooden keel needs to be brushed with fireproof coating).

3. The ridge is installed with several layers of base rolling ants. Multi-layer boards and blockboards are fixed on the wooden keel or light steel keel (the wood base board needs to be brushed with fireproof coating).

4. Install aluminum-plastic panels. Wait for 10 to 15 minutes after the glue is fully coated on the back of the aluminum-plastic panel (mounting surface), and then the board can be put on.

Aluminum-plastic panel is a material commonly used for decoration and building exterior walls, the following is the general aluminum-composite panel installation method:

1.Preparation:

Determine the installation location: determine the installation position and size of the aluminum-composite panel.

Prepare tools and materials: Prepare the required tools, such as electric drills, screwdrivers, hammers, etc., as well as materials such as screws, glue, etc., required for installation.

2.Measuring & Cutting:

According to the required size, use a ruler and an aluminum-composite panel cutting tool to measure and cut the aluminum-composite panel to ensure that it is suitable for the installation position.

3.Mounting the skeleton:

According to the installation position of the aluminum-plastic panel, the supporting skeleton is installed, and the skeleton is generally made of metal or wood to ensure that it is firm and horizontal.

4.Fixing aluminum-composite panels:

Place the aluminium composite panel in the mounting position and fix it to the sail support frame using a screw bridge or other appropriate fixing material.

When fixing the aluminum-composite panel, it is necessary to ensure that the position and spacing of the screws are uniform to ensure the overall stability and aesthetics.

5.Seam Treatment:

For the joints of the aluminum-plastic panels, special connectors or glues are used to treat them to ensure the tightness and aesthetics of the joints.

6.Follow-up Processing:

After the installation of the aluminum-plastic panel is completed, the work site is cleaned up and the garbage and waste materials generated during the construction process are disposed of.

Please note that during the installation of aluminum-composite panels, it is necessary to strictly follow the safety operation specifications to avoid accidents. If you do not have relevant experience or are unsure how to operate, it is recommended that you consult a professional construction personnel or have a professional team perform the installation.

The installation method of aluminum-plastic panel mainly includes the following steps:

1.Prepare tools and materials.

Prepare the necessary installation tools and materials such as screws or rivets, adhesives, air cushions and other necessary installation tools according to the size of the aluminum-plastic panel.

2.Clean the mounting surface.

Thoroughly clean the surface to be installed on the aluminum-plastic such as Xiaoyan slab to remove dust and oil stains to ensure that the surface is smooth and smooth.

3.Adhesive filling.

Fill the gap adhesive in the edge grooves that need to be bonded, and then immerse the edge of the aluminium composite panel in the adhesive.

4.Drying time.

Depending on the guaranteed drying time of the adhesive, wait for the adhesive to be semi-dry before starting installation.

5.Lay the air mattress .

Lay a rubber air cushion on the mounting surface that needs to be bonded, which is conducive to adjusting the installation position of the aluminum-plastic panel.

6.Press to secure.

Place the aluminium composite panel at the position where the slag needs to be bonded, and then apply pressure to bond it.

7.Set the screws.

Nail in the fixing screws according to the planned position to ensure that the aluminum-composite panel is installed firmly.

8.Finally fixed.

Finally, use the plug to repair all the screw holes and gaps to complete the installation of the aluminum-plastic panel. Shen Kai.

The above is the main process of installing aluminum-plastic panels, and the key lies in the full introduction of edge adhesive, reasonable installation and pressing pressure. After installation, pay attention to the final decorative surface restoration.

Hope to provide the content to help you install the aluminium composite panel.

Aluminum-plastic panel is a kind of composite panel commonly used in decoration and building materials, which has the characteristics of beautiful appearance, light weight, waterproof, fireproof and durable. The installation method is mainly divided into the following steps:

1.Clean the wall: Clean the wall with a rag, detergent or water to make sure the wall is neat and dry.

2.Wire positioning: determine the position and size of the aluminum-plastic panel by wire on the wall. Longer aluminium composite panels need to be positioned by horizontal and longitudinal lines.

3.Aluminum-plastic panel cutting: cut aluminum-plastic panel according to positioning to ensure accurate size and avoid waste of surplus sales costs.

4.Joint treatment: cut or fold the corners around the aluminum-plastic panel so that it does not leave seams during assembly.

5.Aluminum-plastic panel installation: Place the aluminum-plastic panels separately on the positioning line and fix them in a certain way, such as by super glue or screws. It should be noted that waterproof partitions at the edges and junctions should be added during installation.

6.Edge banding treatment: After the installation of the aluminum-plastic panel, the corners are filled and sealed with sealing strips.

The above are the general steps of aluminum-composite panel installation, if there are special circumstances or more detailed installation procedures are required.

Aluminum-plastic panel installation process: keel layout and elastic line installation and leveling keel installation of aluminum-plastic panel trimming and sealing The specific process is as follows

1. Grassroots leveling: the original wall foundation is leveled.

2. Spring line: determine the elevation control line and keel layout line.

3. Determine the keel position line: arrange the structural size of the ceiling skeleton according to the size of the aluminum-plastic panel and the area size of the ceiling.

4. Install wooden keel: wall punching, wooden tenon fixing, generally use 20*30 wooden keel, spacing 400 or 600.

5. Install the base board: multi-layer board, blockboard fixed on the foundation of the wooden keel or on the light steel keel.

6. Install the aluminum-plastic panel: immediately get the glue to fill the back of the aluminum-plastic panel (installation surface) and wait for 10 to 15 minutes, and then the board can be on.

7. End treatment: When the edge of the wall around does not conform to the modulus of the square board, after obtaining the approval of the designer and the supervisor, the method of closing the edge of the square board and the wall board can be not adopted, but the strip board or paper gypsum board is used for ceiling treatment.

Dear, hello, I am glad to serve you The following I will answer for you: Aluminum-plastic panel is a commonly used material for walls, and you need to master the steps when installing. Let's take a look at the installation method of aluminum-plastic panel directly attached to the wall:

Grassroots leveling, elastic line|First, the base layer of the wall is leveled, and the line is bounced on the wall; Determine keel position line |Then arrange the size of the ceiling skeleton according to the size of the plate, and then determine the position line of the keel; Install the wooden keel|Punch holes in the wall, install wooden keels, and keep the spacing at 400-600 mm; Installing the Base Plate|Then install the base plate, and then you can install the aluminum-plastic panel, apply the glue to the back of the plate, and wait for the installation later; Wall Top Treatment|It is best to treat the top of the wall, and you need to use strip board or paper gypsum board to do the ceiling treatment.