What does it mean that the lamp light of the BenQ projector is on?

If the lamp light is on, the bulb may be broken, or there may be a problem with the lighter.

The temp light is on due to the alarm of the temperature control part, maybe the fan stops, or the temperature is too high to exceed the warning line.

If the projector cannot be used normally, it is recommended to try to unplug the power and signal cables on the back of the projector, wait for 5-10 minutes, and then reconnect the cables to see if it can be turned on normally.

If it still does not work properly, we recommend that you call BenQ after-sales technical support.

**400-888-0333 for repair.

Hello nexus500.

If your projector cannot be used normally, it is recommended that you try to unplug the power cable and signal cable on the back of the projector, wait for 5-10 minutes and then reconnect the cable to see if it can be turned on normally. Such as temp light on.

It is caused by the alarm of the temperature control part, maybe the fan stops, or the temperature is too high to exceed the warning line. For this problem, it is recommended that you call BenQ after-sales technical support**400-888-0333 for repair.

Benq Superman.

lamp means light bulb.

This light is on to indicate that the life of the bulb is almost up, and the light should be replaced immediately.

temp means temperature.

This light is on to indicate that the internal temperature of the machine is too high, and you should immediately remove the dust or check whether the fan is still working and whether there is any problem. If it is not solved in time, the motherboard will be burned and the bulb will be blown up due to the high internal temperature.

If the lamp light flashes red, it basically means that the bulb is broken.

temp means that the temperature is too high.

BenQ projector turns on lamp and temp at the same time, and it can't be turned on.

Hello, glad to answer for you, solutions:1First check that the power socket used by the projector is powered on and that the power cord of the projector is plugged in tightly.

2.Secondly, if the projector is powered on normally, then check the projector's indicator lights "lamp" and "temp", if the lamp light turns red, it means that the projector lamp is at the end of its life, and the lamp needs to be replaced. If it is a new bulb, it may be that the projector bulb was not cleared when it was used, and it can be cleared.

If the temp light is on, it means that the projector may have just been used, and the temperature has not dropped yet, turn off the projector, let it rest for a few minutes, and then turn it on. 3.Finally, if the indicator lights do not turn red, and the envy button on the center control panel of the projector cannot be turned on, use the remote control to try whether it can be turned on.

The projector lamp lights up red may be the following situations: 1. The projector lamp is faulty or the lamp cannot be used normally until the life of the lamp; 2. The projector fan is faulty, the speed is abnormal or stopped, resulting in the machine shutting down; 3. The excessive dust accumulation inside the projector leads to the blockage of the filter, the machine is poor in efficiency, and the machine temperature is too high to cause the machine to self-protect and automatically cut off the power. 4. The power supply of the projector, the lighting version, the motherboard or the color wheel are faulty.

You can try to repair the projector lamp, repair the projector fan, clean the dust and filter, repair the power supply, light plate, motherboard and color wheel, etc.

Dear Hello <>

The projector temp and lamp light are on, if it is lamp flashing, it should be the lamp when the time is up, remind you to replace, if it is temp flashing, it should be overheated. Solution: Disassemble the bulb cover, remove the bulb and carefully check whether there is any poor assembly.

Further, look at the bulb for signs of bad things such as burnout or many bubbles; Check whether the lamp is defective, and re-test it after replacing the lamp; Check whether the color wheel is OK, and retest it after replacement; Check whether the feedback cable (5pin cable) connected from the light igniter to the fan board is well connected, and test it after reconnection; Measure whether the feedback line body is defective, and re-test it after replacement; According to the current situation, 1Pay attention to personal protection: During the epidemic, you should pay attention to personal protection, wear a mask when you go out, don't go to crowded places, and avoid gatherings.

Always open windows for ventilation at home, and try not to go to medium and high-risk places. ​2.Regular nucleic acid testing:

Regular nucleic acid testing should be done to understand your physical health. If the nucleic acid is positive, isolate it in time**, which will help cut off the transmission route in time. ​3.

Vaccination: If individuals do not have contraindications to vaccination, it is recommended to get vaccinated as soon as possible to strengthen their resistance to the disease. If you have a fever, cough, etc., you should seek medical attention as soon as possible.

Hope the above is helpful <> you

The projector lamp lights up red generally in the following situations:

1.There is too much dust inside the projector, and the filter is blocked, resulting in poor heat of the machine ventilation fan, and the machine will self-protect and automatically power off.

2.If the projector lamp fails or the lamp reaches the end of its life, it needs to be replaced.

3.The projector fan is faulty and the speed is not normal, resulting in shutdown.

4.The projector has a power failure.

5.The projector illuminated version is faulty.

6.The projector motherboard is faulty.

7.Projector color wheel failure, etc.

In this case, it is best to find a professional projector maintenance personnel to test, and it is better to analyze and judge specific problems. In this case, it is best to find a professional projector maintenance personnel to test, and it is better to analyze and judge specific problems.

Hello: It is recommended that you can turn off the power cord on the back of the projector after the projector is turned off, wait for 5-10 minutes and then turn it on to view, if there is no improvement, it is recommended that you contact the service network to detect and confirm. For more information, please refer to:

BenQ China--Service Support--Information Query--Service Outlets--Select the specific product type, province, city, and click Query.

Benq Superman.

Is it that the light bulb is not working? Didn't know you were a friend there. You can take the projector to the nearest BenQ Authorized Repair Center for testing.