How to wire the 4 wires of fire emergency lighting fixtures

One by one, a switch live wire, a charging live wire.

Precautions: 1. Accurately grasp the characteristics of various wiring methods, so as to avoid blind wiring, which cannot play its due role;

2. If the emergency lighting is used as a part of the usual lighting, the three-wire controllable connection method should be adopted.

3. For multi-storey public buildings, if there is no elimination control center, the emergency lighting fixtures of each part can be controlled by local switch (single lamp single control or multi-lamp control) or three-wire connection method of centralized control in the distribution box.

Connect the cable of the control switch with the control board of the emergency light, pay attention to the line connection above the emergency power supply, and the corresponding live wire should be connected with the binding post of the live wire, the neutral wire also needs to be connected with the binding post of the neutral line, and the line of the controller should be connected to the place.

Through the switch, you need to access the switch wire, one of which needs to be connected to the neutral line, and another one to be connected to the ground wire, which is connected to the emergency switch fluorescent lamp.

The shell is fine.

The normal one is 1 neutral wire, 1 switching live wire, 1 charging wire, and 1 strong ignition wire.

The product should have 4 terminal holes, which should be connected accordingly.

If it is necessary to connect the emergency lighting circuit with strong start, the normal fire wire leads to the switch of phase B (green), and the strong fire wire leads to the AC contactor.

The AC contactor should be equipped with a control line to work normally, and a single input and single output module of the alarm system or an intermediate relay driven by the door button should be added to the box.

According to the physical drawing number, the terminal pile is connected to the external rechargeable battery, 1 is connected to the positive pole of the battery, and 2 is connected to the negative pole of the battery. The No. 3 pile is connected to the live wire that comes out of the wall control switch, (note that it is controlled by the switch and can be turned on and off), and the No. 4 pile is connected to the zero line.

Without an external battery, the light will not turn on automatically when the power goes out.

Turn left|Turn right.

One by one, a switch live wire, a charging live wire.

Remember where you went.

There are a total of 4 wires: one directly connected to the fire wire (fire status and daily charging cable), one connected to the switch wire through the switch (normal lighting), one connected to zero, and one connected to the ground. From the safety point of view, there must be a grounding wire (connected to the fire emergency fluorescent lamp shell) in accordance with the requirements of the specification.

In general, the two white wires of the emergency power supply are connected to the energy-saving lamp, the red line is connected to the Changming line, the black wire is connected to the switch live wire, and the blue wire is connected to the zero line. (There are also some products with different wire colors, depending on the wiring identification on the emergency power supply). The installation is the same as that of a normal downlight, except that an extra emergency power supply is added to the ceiling.

Emergency lights are installed in the same way as ordinary ceiling lights. Wiring: The switch wire is connected to the lamp head, and the Changming wire is connected to the emergency power cord.

Neutral line sharing.

1. Non-persistent:

Features: It usually does not light up, and it will automatically convert to emergency lighting after a power failure.

2. Continuous:

Features: Usually bright, automatically converted to emergency lighting after power failure.

3. Controllable:

Features: The emergency lamps can be controlled to be turned on or off at ordinary times, and the emergency lights are lit immediately after the power failure. K is the control switch, which is the most common connection method for emergency lights. Note: The yellow and green wires are grounded.

How to connect the emergency light strip lighting wire.

Summary. Hello, the 4 wires of the fire emergency light are: fire wire, neutral wire, grounding wire, and strong start line.

The live wire is connected to the charging cable of the emergency light, and the neutral wire and the grounding wire are connected to the neutral wire and the grounding wire of the emergency light respectively. The strong start line of the fire emergency lamp is connected to one end of the normally open point on the relay after the fire wire is separated, and the other end of the normally open point is connected to the strong start line of the emergency light, and then the control module of the fire control room, that is, the input and output module, the module will output 24V voltage after the control room is opened, and the two wires are connected to the coil of the relay, after the relay coil is energized, the normally open point will be closed, and the electricity of the emergency lighting box will enter the strong start line of the emergency light through the normally open point that the relay has been closed. The emergency lights will be forced to turn on. The strong start line is specially used for the fire control room to force the emergency lights to be lit when the fire is linked.

The emergency light must be lit when the fire is linked, regardless of whether there is electricity or not, the emergency light must be on when the fire is linked.

What does the fire emergency light strong start line mean? How to connect the 4 wires of fire emergency lights?

Hello, the 4 wires of the fire emergency light are: fire wire, neutral wire, grounding wire, and strong start line. The live wire is connected to the charging cable of the emergency light, and the neutral wire and the grounding wire are connected to the neutral wire and the grounding wire of the emergency light respectively.

The strong start line of the fire emergency lamp is connected to one end of the normally open point on the relay after the fire wire is separated, and the other end of the normally open point is connected to the strong start line of the emergency light, and then the control module of the fire control room, that is, the input and output module, the module will output 24V voltage after the control room is opened, and the two wires are connected to the coil of the relay, after the relay coil is energized, the normally open point will be closed, and the electricity of the emergency lighting box will enter the strong start line of the emergency light through the normally open point that the relay has been closed. The emergency lights will be forced to turn on. The strong start line is specially used for the fire control room to force the emergency lights to be lit when the fire is linked. The emergency light must be lit when the fire is linked, regardless of whether there is electricity or not, the emergency light must be on when the fire is linked.

Hope mine can help you.

1. First loosen the screws at the bottom of the emergency light.

2. After unscrewing the above screws, you can open the cover of the emergency light.

3. After the attack, you can see the internal emergency power supply of the emergency light. There are two live wires, a control line and a neutral line.

4. Use a screwdriver to loosen the screws on the control circuit board to facilitate the connection of the control cable later.

5. Connect the cable of the control switch to the emergency light control system board.

6. Then connect the emergency power supply with the emergency indicator line.

7. Then connect the emergency controller circuit.

8. The emergency light is now connected.

What line is used for fire emergency lighting? Hello, I am glad to answer for you<> pro in the selection of wires is generally to choose flame retardant wires, this kind of wire flame retardant performance is good, the wire is mostly used in power transmission and distribution, bright control, alarm, talk about widening the fire protection system product line, etc. The installation of fire emergency lights is very strict, we need to test whether the outer packaging of the product is damaged, whether there is a problem with the appearance and structure of the fire emergency lights, and conduct on-site inspection (inspection) and selection compliance inspection of system equipment, materials and accessories, and unqualified equipment, materials, accessories and products that do not meet the requirements of the design drawings shall not be used.

Hope mine can help you <>

Do you have any other questions?