How can my Tissot watch go faster and faster

Five common reasons for watch time error and watch time inaccuracy:

1) Insufficient power reserve: You need to check whether the power is sufficient, if the amount of movement of the self-winding mechanical watch is very small, it may also cause insufficient power reserve, you can replenish the power by manual winding, and then observe whether it continues to have the phenomenon of fast and slow.

2) Insufficient power: If the quartz watch suddenly finds that it is slow, it is likely to be caused by insufficient battery energy, and you can send the watch to a special maintenance point to check the power.

3) Hit or hit: The watch is very tight, if it is hit or hit, it may cause loose damage to the internal parts, and it may also cause the problem of running time. This is to be dealt with in a timely manner.

4) Need to maintain: The lack of oil in the movement or the wear and aging of internal parts may cause time problems, which need to be maintained, and need to be sent to the designated maintenance point for maintenance services.

5) In addition to the above common situations, the watch is affected by some ambient temperatures: if the hairspring of the watch is magnetized, the watch will not be accurate.

After-sales ** Tissot watch after-sales repair center.

Tissot watches are not on time.

It could be a battery issue, batteries of different voltages can cause the quartz resonator frequency to change. Therefore, we should choose a model or a battery with the same voltage as the primary battery. If the two pins of the quartz resonator itself are loose or the quartz resonator seal tube is not well sealed, it will be the quartz resonator frequency generation.

Problems with the control accuracy system in the IC circuit can also lead to changes in the frequency of the quartz resonator and the need to replace the circuit board. So we're going to make sure if the battery is running out or not.

Usually quartz watch batteries have a battery life of 1-2 years. When we exercise vigorously, it is easy to make the watch inaccurate, for example, the balance wheel swing of the watch is too high, and the violent movement of external force is used in the balance wheel, which aggravates its rotation amplitude, and the watch has to "hit the pendulum"; An additional common end cause is that the watch movement parts are magnetized.

After-sales **4006590877

There are many reasons for the watch to go fast, it may be that it needs to be cleaned and maintained for a long time, it may be magnetized, it needs to be demagnetized, it may also be that the gossamer is messy, you had better go to a professional watch maintenance point for maintenance, so you can rest assured, I hope mine is helpful to you!

Adhesion by magnetic field swimming. Fall, knock, violent collision, adjust the speed of the hairspring is very soft, very thin, very fine, very elastic, easy to hang on the small parts of the balance, so that the balance wheel goes fast, the watch goes fast. If the above situation occurs on the watch, it is recommended to take it to the center immediately to solve it, so as to avoid further damage to the watch after a long time.

The reason why the watch goes fast:

1. If the wearer has a vigorous movement acting on the balance wheel, which aggravates the rotation amplitude of the balance wheel, it will cause the watch to swing and speed up the time.

2. The magnetization of movement parts is also one of the main reasons for the acceleration of the watch.

3. The watch has suffered a collision, and there will also be a problem, that is, the secondary outer ring of the hairspring may touch the outer pile of the hairspring, which will appear on the façade and in the dynamic form, which is also one of the fault problems that affect the walking at hand.

It may be magnetized, and degaussing is fine.

Watch maintenance and repair can refer to the service center of Xidan Joy City Office Building, Xicheng District, Beijing, to provide Tissot watch strap customization, cleaning and maintenance, identification, refurbishment, fault repair, watch appearance and replacement of damaged parts, and strap replacement services. Our technicians have undergone strict professional skills training and provide two years of after-sales guarantee services. The service center is guided by the watch manufacturer on the spot**, **transparent, no hidden consumption, no additional charges.

1. The speed of the mechanical watch is mainly determined by the pendulum frequency, usually the larger the pendulum amplitude, the smaller the pendulum frequency, and the smaller the pendulum amplitude, the greater the pendulum frequency. Generally, watches rely on the retraction and release of the hairspring to control the swing, which is the basic principle of adjusting the speed and slowness. If the hairspring is longer, the swing will increase, the frequency will be smaller, and the watch will be slower; Conversely, the more the pendulum frequency increases, the faster the watch will be.

2. The structural problem itself, due to the gravitational force of the earth, the offset of the horizontal position and the vertical position will produce a displacement, the mainspring is tightened from the top to the relaxation, the torque is unbalanced, and the external temperature, magnetic field, vibration, etc., even if the mechanical watch increases some frequency, it is impossible to achieve the accuracy of the quartz electronic watch.

3. The effect of the magnetic field, after the hairspring is magnetized, the circle between the rings is only shown when wearing, there is a sticky or short-term lap, especially in the façade, the hairspring will hang down due to its own gravity, and the shaking of the arm will intensify its radial movement, and the magnetic energy utility is shown because of this.

4. The balance of the balance wheel and the balance spring, especially the balance wheel, the balance wheel is very poor, which will cause the balance wheel to highlight the precision change of the surface under a certain swing.

There are four reasons why mechanical watches are moving faster:

1. The lubricating oil of the mechanical watch penetrates into the hairspring, or leaks, or overflows, so that the extremely precise hairspring is "sticked" together, shortening the length of the hairspring, which leads to the speed of the balance wheel of the watch to accelerate, resulting in time "running fast", this situation needs to be sent to the repair shop to the professional master to deal with, so that the hairspring can return to normal.

2. It is still a hairspring, and the hairspring is hung on the outer pile of the hairspring. Due to vibration and other reasons, the hairspring was instantly "deformed", "rubbed" on the outer pile of the hairspring and hung on it. This is the same reason as the "sticky" oil of the hairspring, which leads to the "running fast" of time.

This kind of harm is greater, and it needs to be repaired in time, and the hairspring can be "picked" away from the outer pile of the hairspring.

3. The hairspring is magnetized, and the time "runs fast" due to the contact magnetic field, and the watch can be put into the demagnetizer to demagnetize.

4. The fork pad of the escape wheel is faulty, and the kinetic energy release speed of the escape wheel cannot be effectively controlled. As a result, time "runs fast". I had to swap it out. It also needs to be sent to a professional watch store for repair.

For the handling of mechanical watches, demagnetization is the first priority, and it must be neat and thorough demagnetization; Then check the position error of the watch, continue to check the hairspring, clean the hairspring with alcohol, it will be more fuel and tidy, volatile is good, and the low-quality fuel and magnetic field will make the hairspring show up to circle or attract each other. It is best to do a timekeeping quiz on the repaired watch, and it is best to do a long-term dynamic check to see which all-round rotating experimental rack is to be put on, or to wear it directly to check carefully. If it is a deeply hidden problem, we can only detect it with the help of relevant instruments.

The mechanical watch goes fast first because the position error of the watch is relatively large, for example, the precision of the hand surface and the face is different, the error of the façade luck is relatively large, when worn, its comprehensive uniform daily error is relatively increased, the position error is a key indicator of the performance of the watch, and the general change index should be as small as possible.

There is also a common problem with the fast movement of mechanical watches, that is, the secondary outer ring of the hairspring rubs against the outer pile of the hairspring, and the inner is also displayed on the façade and dynamics, especially if the watch has been touched before, and the hairspring is the most likely to have problems after deformation; This sub-position, depending on what the movement is, if it is now a general ETA class men's watch movement, it is easier to display the position on the left or the upper handle of the watch handle on the wrist, this situation requires the adjustment of the space between the secondary outer ring of the hairspring and the outer pile of the hairspring, and there should be a reasonable and safe distance between them.

If you have any questions, please click on the avatar to consult**, welcome to call.

Our mechanical watches often have the situation that the time is not accurate, and most people wonder if the mechanical watch is broken. There are many reasons why a mechanical watch can be parked, but there are several main reasons.

1. Insufficient kinetic energy: The watch is not winded enough, and the kinetic energy is insufficient. In particular, automatic watches require more arm movement, and the winding efficiency is very low. If you usually exercise a little bit, you can wind it manually, which can ensure enough kinetic energy.

2. Gear failure: Gear train failure such as deviation wheel and center wheel failure will lead to the condition of stealing stop of the watch. These situations are often not easy to detect and require disassembly, careful inspection and testing to find out the problem and solve the problem.

3. Lack of maintenance: mechanical watches should be maintained every 2-3 years or so. If it is not maintained for a long time, a large amount of oil sludge will be generated inside. Friction between gears increases, causing slippage.

The Tissot watch is slowing down, first of all, see how much error there is, if it appears after a long time, it is normal.

If it slows down in a short time, it means that there is a problem with the machinery, and you need to find after-sales maintenance or debugging.

The Tissot watch is slow, probably because of a lack of power. If you are using a Tissot mechanical watch, you need to check that the power is sufficient.

It may be that the battery is not working well, or there is a problem with the internal parts of the watch.

It is relatively normal for mechanical watches to go fast and slowly, and basically all mechanical watches will have a time difference.

Go to the counter and ask, or go to the watch repair ** to ask.

What should I do if my Tissot watch is slow, of course, it is to go to the watch shop to proofread and adjust it.

This is normal and does not need to be treated.

According to the latest data of the National Watch Testing Center in 2013, under the premise that the mechanical watch is full of spin and normal use, the error of the excellent product is 25 seconds, the error of the first-class product is 45 seconds, and the error of the qualified product is 1 minute. As long as the error is within these ranges, it is within the margin of error permitted by the state.

Many factors such as the inadequacy of the materials used in the manufacture of the watch, the processing and assembly of the watch, or the magnetic field near the person will affect the size of the error. Chairman Wang said that the user's wearing habits are also a factor that cannot be ignored.

Reasons why Tissot watches are slow:

There are two main types of watches: mechanical watches and quartz watches. It is very common for a mechanical watch to be slow, and a large part of it is caused by your lack of exercise. It may be that the movement needs to be lubricated with oil to reduce friction.

It may be that there is a foreign object obstructing the movement. These are very easy to handle, but it is recommended to deal with professional after-sales service. The quartz watch is slow, it may be that the battery is low and the battery needs to be replaced.

It is also possible that the circuit board is aging and needs to be maintained.

1. The handle in the middle is screwed like a screw, according to the waterproof design of the counter, and when adjusting the time, it is screwed downwards counterclockwise, and it is loosened like a teacup lid.

2. After unscrewing, it is screwed directly upwards at 0 gear, and it is manually wound. (If you buy a new watch or have not worn it for a long time, please manually wind it for 30 turns when you wear it again, so as to ensure the energy of the watch, which is usually not needed).

3. Pull it lightly, it is 1 gear to twist up to adjust the week, and down to adjust the calendar.

4. When pulling, it is 2 gears that can adjust the time.

Care for Tissot watches:

1) When wearing a watch, the sweat on the hands is corrosive to the case, the all-steel case is better corrosion resistance because it is nickel-chromium alloy, and the semi-steel case is copper, which is in contact with sweat for a long time, and is easy to corrode, so you should often wipe off the sweat with a soft cloth or put on a plastic watch holder to prevent it from being eroded by sweat.

2) Do not open the back cover of the watch at will, so as not to enter the movement and affect the normal operation of the watch.

3) Do not put the watch in a closet with mothballs to avoid the deterioration of the watch oil.

4) Do not put the watch on the radio or TV to avoid magnetization.

5) Watches that are not worn for a long time should be wound regularly once a month so that the parts will not be in a stationary state for a long time, so as to ensure the operation performance of the watch machine.

The slow movement of a mechanical watch is first and foremost due to the relatively large position error of the watch. For example, the accuracy of the surface of the dial and the bottom of the dial is different, and the good luck error on the façade is larger. When worn, the overall average daily error increases relatively.

Position error is a key indicator of the watch's lucky performance, and the general variation indicator should be as small as possible.

Also, the slow movement of a mechanical watch is most likely due to the influence of a magnetic field. After the hairspring is magnetized, the loops between the rings are only visible when worn and have sticky or short loops, especially on facades. The hairspring will sag due to its own gravity, and the shaking of the arm will exacerbate its radial motion, thus showing the action of magnetic energy.

Finally, the factors that affect the position error also include the balance between the balance wheel and the hairspring, especially the balance wheel. The balance wheel is very poorly balanced, which will cause the balance wheel to highlight changes in surface accuracy at a certain amplitude.

The watch is not allowed to run inaccurately:

1.Watch magnetization: The watch is in too much contact with items with magnetic fields, which leads to the phenomenon of magnetization of the watch, causing the watch to be inaccurate.

After being magnetized, the watch may stop, slow, or fast. After the watch is magnetized, its magnetism will not recede on its own, and it needs to be demagnetized to restore it to normal.

2.Lack of maintenance: If the watch lacks maintenance, it will lead to wear and tear of parts, dry up the sludge, affect the normal running time of the watch, and make the watch appear fast and slow.

3.Mechanical failures: Mechanical failures such as watch balance spring failures, escapement failures, and component slips can cause the watch to be fast and slow.

Mechanical watches are sometimes fast and sometimes slow, and it may be caused by severe impacts, water ingress, etc. Quartz watches are generally very accurate and less prone to time failures. In the case of adequate maintenance, it is more likely to be fast and slow, which is more related to the failure of the circuit board, or the poor contact of a certain part.