Which router has good security performance and can be connected to two optical fibers at the same ti

Hero, can the router be connected to optical fiber?

1. Fiber-to-the-home cannot be directly connected to the router for use, you need to connect the optical modem, and then connect the network cable to the router. According to the different optical modems used, there are two situations:

1. The cat comes out of the network cable and connects directly to the computer, and the computer needs to be dialed up to connect

Set the router WAN port parameters to PPPoE dial-up mode, and enter the broadband account and password, and set other settings according to the router manual or according to the router setup wizard. After the settings are complete, use a network cable to connect the modem to the WAN port of the router.

2. The optical fiber connection device is a GPON device that integrates the cat and the router, and the computer directly connects the cat without dial-up connection of the computer, and the computer can be connected to the Internet by automatically obtaining the IP

Set the WAN port parameter of the router to dynamic IP, and pay attention to modify the IP address of the LAN port, so as not to be in the same IP segment as the IP address of the modem to avoid IP conflicts. For example, if the IP address of the cat is changed to the first three digits of the LAN port of the router, at least one of them cannot be the same as the first three digits).

Other settings can be set according to the router manual or according to the router setup wizard. After the settings are complete, use a network cable to connect the modem to the WAN port of the router.

Set and turn off the DHCP function of the LAN port of B, the WAN port parameters do not need to be set, and the wireless settings of the router are set according to the manual. After the settings are complete, connect the modem to the LAN port of the router with a network cable.

2. Connect the router behind the router and refer to the above "2" case connection settings.

I think switches and routers are all about the same!

A router can also be used as a switch, i.e. without a WAN port!

That's equivalent to expanding your office's router port!

Office LAN cable == LAN port of switch or router!

good luck

In fact, you can use a router or a switch, and you need to set up the same router.

The fiber router is assumed to be No. 1.

Your family's assumption is number 2.

No. 1 can access the Internet after the IP address and gateway provided by the optical fiber are set.

Set the IP address of router 2 to a different IP address from the same network segment as router 1.

Then select the static IP address for the dialing mode.

Gateway 2 is the IP address of Router 1.

If DNS can be set by default, you don't need to set it.

In fact, you can just change the switch.

Take a cable from the office to your home switch, and then 2 cables from the switch to your computer.

Fiber-to-the-floor, and then the switch splits to the user's home, as long as the port rate set on the switch is consistent with the transmission rate of the router's WAN port.

Yes, as long as there are no restrictions on telecommunications, anything is possible.

Yes, buy an optical modem, and then access the ordinary route, this person who asks the computer city to sell these knows best.

You can't use a switch essentially.

Go to the electronics market and buy a router, there are installation instructions in it, just follow the instructions, it's quite simple. The crystal plug of the fiber broadband cable is plugged directly into the WAN interface of the router. The Mercury brand router is more than 40 yuan.

It's no different from ADSL. Just use it the same.

Just set a fixed IP address in the route to access the Internet.

Fiber broadband is generally given to a static IP, and you can set the router to be static.

Isn't that a principle?,What's wrong with optical fiber?,Isn't it a truth?,It's just that you need to configure a router?,Just buy a high-end router.。

3: Network parameters--- LAN port settings -- change the default to restart the router to access the Internet normally.

The address on your route must be static, mainly to open the DHCP service in the router, which is a service that automatically assigns an IP.

1. Connect the network cable from the fiber optic transceiver to the router WLAN

2 Web login to the router, set the network parameters WLAN, connection type dynamic IP, set DNS, and enable DHCP

Optical fibers seem to be static IP, let the optical fiber set it for you, directly connect your route to the fiber modem, hit ** and ask them what the IP is, on the line, if it is dynamic, it should be the same as the cable, just set the dial.

I really don't know about the light and dynamic IP.

Aitai 4210g This thing, I remember, is all graphic stuff, you look at his manual.

Or give Aino**.

Reinstall the NIC driver (or change the network cable).

Turn on Dynamic Allocation (DHTP) once connected to the router

Set up a username and password.

It should be fine.

Use the network cable to connect, then buy a 4-port router, and connect it after the cable is done. But if you don't know how to make wire, you have to ask a person, and you have to borrow wire strippers and crimping pliers.

The landlord can use a wireless router. It is convenient and beautiful, and it is more messy to connect a lot of wires. As for TVs, many smart TVs now have built-in wifi, and you can also use wireless networks.

The network cable, the router will give it.

Lower the sleeve for easy replacement later.

It must be a network cable, brother, you think too much.

Bind the MAC address of the computer to the IP address, and then set the bandwidth of each port.

10m is definitely enough!

1. Internet problems and routing connection problems.

2 Intranet virus issues.

What is the egress bandwidth of the router? Is it clogged?

Just plug in a switch and you're good to go. If you have already bought a router: The following total router is referred to as Route 1, and your own router is referred to as Route 2

1. Turn off the DHCP function of route 2, plug the network cable from route 1 into the LAN port of route 2, your computer is connected to the other LAN port of route 2, and the WAN port does not need to be connected to any network cable, this method uses the router as a switch. If it doesn't work, use method 2: 2, connect the network cable connected by route 1 to the WAN port of route 2, and leave the others still.

Enter Route 2 settings, open IE, enter the IP by default, enter the router and turn on the DHCP service that was closed in the previous step, modify the "Network Parameters" > LAN port settings, modify the original IP to 192, save, and restart the route. If you can't access the router after restarting, modify your local connection, disable it, and then enable it. After entering Route 2, set the "Network Parameters" of the router 》WAN port settings, select "Static IP" for Internet access mode, enter the IP assigned by Route 1, if you don't know the IP, plug the network cable connected by Route 1 to another computer, you can see it, and then connect back to the WAN port of Route 2, and you can go to the Internet after setting the IP.

Thank you for the trouble to adopt!