The CPU is seriously high at 98 degrees, and the core temperature is only 35 and 36

You can touch the heat sink with your hand after a period of time after turning on the machine, if it is hot, it means that the temperature is indeed high

98 degrees usually the machine will automatically restart

If the temperature is high, remove the fan and reapply the heat dissipation glue for a long time to see if the heat sink is completely bonded to the CPU

If the temperature is not high, it is a BIOS problem

You can ignore it

Wait for the new BIOS to appear

Of course, you can also downgrade and flash the BIOS

It may be that the CPU is not supported

But it can be forced

When the CPU reaches 98 degrees, your motherboard should have an alarm or automatic shutdown, and the software should not be able to measure it.

Are you mistakenly not C but F, we use C to represent temperature, and the gringos look at F, and F is generally 3 times that of C.

BIOS suggests flashing a new one, may not support E6500 information, after all, E6500 was released in August 2009, and your BIOS is the 08 version.

Use Master Xia Lu to look at the temperature.

You're talking about the display parameters are not normal! But is it the same as not upgrading?

If the usage is normal, it's a matter of displaying numbers!

What brand of promotion!

The temperature of the AMD processor is too high, if you rule out the reason of the heat sink and silicone grease, most of the reason is that the silicone grease inside the CPU top cover is dry!

The solution is: use a razor blade to cut open the top cover of the CPU and operate carefully! You can also use a thin screwdriver to pry, so it's okay to be careful.

Clean up the dried silicone, reapply the high-quality silicone grease, close the top cover, and finally fix it again with glue!

Good luck! Anyway, there are only a few dozen pieces of stuff on it. Think about it, it's generally okay to be careful.

At least a suggestion! Think about yourself before you can accept the risk!

The CPU core temperature is more than 30 degrees higher than the surface temperature, which does not indicate that the CPU is abnormal.

First of all, this temperature measurement software is not accurate, even if the probe is used to measure the temperature of the CPU directly, it is not very accurate, because the probe is far from the CPU and the environment is different, and the measured value is different.

In addition, the so-called core temperature refers to the temperature of the surface of the core part inside your CPU, the CPU temperature.

Refers to the temperature of the ceramic on the surface of the CPU. Since the CPU core is covered with a layer of ceramic, there will be a certain difference from the core temperature.

As for the core temperature, you don't have to worry about it, the CPU temperature generally refers to the temperature of its ceramic surface, as long as it does not exceed 50-55, it is no problem, you may be confused.

The reason why Inter didn't release a 4GHz CPU and switched to Core.

series, that is, for this reason, as they found, use silicon materials.

The CPU core has reached its limit, and 4GHz is difficult to be broken through, and its internal temperature is compared with magma.

The surface temperature is comparable.

Your problem is the CPU problem of this batch, there are two points, the first is that the silicon grease between the top cover of the CPU and the CPU chip is dry, this problem is to open the top cover of the CPU to change the silicone grease, and the second is due to the long-term high-temperature CPU and the aging and deformation of the pins of the motherboard, this can only be repaired or replaced.

Alas, AMD's core temperature sensor error problem, my 5000+ and 4800+ are the same, installed on the 780 chipset to boot up is 100 degrees, installed on different motherboards can display a temperature of 40 degrees lower. As long as the surface temperature is not too high and the machine is not thermally protected, it will be fine.

If the temperature is too high, don't keep it off and on, which will cause direct costs to the CPU processor, or take it for maintenance.

Swap out a heat pipe heatsink with an overclocked three. Hehe,,The effect is very good,

If you have had this problem before.

Maybe the thermal conductivity layer between the fan and the CPU is dry. Buy a few bucks and paint it yourself.

If you're looking for a new machine, let's change the fan.

Is there any plaster under the fan?

Change the silicon, pay attention to the tightening screws of the fan evenly to ensure that the contact surface is firm.

There are several reasons why CPU heat dissipation problems:

1. Overclocking; 2. The fan does not rotate;

3. Dust blocks the heat dissipation port;

4. Heat dissipation grease;

5. Heat dissipation copper pipe.

Solution: 1. Determine whether to overclock, if you don't know how to overclock and overclock according to the textbook, it is recommended to recover.

2. Make sure that the CPU fan is running normally, listen to the sound to judge, if not, replace the CPU fan;

3. Clean up the dust;

4. Wipe the original silicone grease clean and replace the heat dissipation silicone grease;

5. If none of the above problems are true, it is a heat dissipation copper pipe problem, which needs to be replaced to solve.

Hurry up and shut down, open the case, and turn on the machine again to see if the fan is rotating, whether it is spinning fast or not, there is a problem with the fan.