How much is a rear tail light for Hiromoto Lingpai

Honda Lingpai taillights are about a few hundred yuan, depending on personal needs.

Lingpai tail lamp disassembly: we need to prepare the tools used in the whole dismantling process, a word to change the cone, a small wheel, a No. 10 sleeve, or an alternative No. 10 wrench.

Open the trunk with your car key. After opening the trunk, observe the trunk side lining that needs to be disassembled for the rear tail lights, we will find that there is a black clip that is stuck on the trunk lining, take out the word change cone, and gently pry the clip open with a word change cone, pay attention to be sure to pry it gently to avoid priing the clip off. Disassemble the wire speed plug.

Then disassemble the rear tail light nut, and you can take out the tail light.

Precautions for the use of Lingpai lighting:

1. When preparing to overtake at night, remind the overtaken driver alternately by alternating high and low beams.

2. When there are no street lights on the highway at night and there is no car far ahead, the high beams should be turned on to ensure that the line of sight is as far as possible to prevent obstacles from suddenly appearing in front of you and have no time to dodge.

3. When driving at night on other dark road sections and there are no cars and pedestrians in front of or on the opposite side, once there are cars and people, please switch to low beams.

4. When you need to prompt others or use lantern language. Another point to note is that in foggy weather, do not turn on the high beams, at this time the high beam will form a scatter, making other drivers more unable to see the road conditions clearly, increasing the risk factor.

Note that the gas in the halogen bulb has pressure. Always handle with care and dispose of halogen bulbs properly. Protective eyewear must be worn when disassembling and disassembling the bulb.

Protects the bulb from wear and scratches. When the bulb is lit and there is no encapsulation, protect the bulb from contact with liquids. The bulb must be lit after the bulb is loaded into the headlight.

Replace cracked or damaged headlights. When replacing a halogen bulb, never touch the glass part with your fingers that are not wearing gloves. Children are not allowed to touch the light bulbs.

Dispose of old bulbs with care. Otherwise the bulb will**.

The price of the rear tail light pure original 4S is: about 800!The pure ones of the accessories manufacturers are also between 500-720.

It seems to be around 1300, and the 2750 that I changed with the rear bar last time.

The original 1400, not the original 670. I just changed it today.

980!The next day after the new car, my wife installed a telephone pole, and I was speechless. . .

** On 500--900 dead s is definitely more expensive.

Honda Lingpai original headlight factory ** is about 800. Honda Lingpai bulb maintenance: 1. Check whether the lights are working properly every day.

Checking your lights on a daily basis is not as simple as just looking at them, and when you check them, you need to check whether the different types of lights (such as turn signals, tail lights, fog lights, etc.) are working properly. In addition, it is also necessary to check whether the direction of the headlights is offset and whether the brightness of the lights is sufficient. Daily inspection of the working condition of the car lights can keep track of the condition of the lights and avoid accidents.

2. Replace the bulb regularly. The bulb of a car lamp is a consumable and has its inherent lifespan. Many people think that even if the bulb is used for a long time, as long as it is still on, it is fine.

This is actually a fluke mentality. The bulb will dim after a long time, and the irradiation distance will become shorter, which directly affects driving at night, which is a very big safety hazard. Therefore, once you find that the bulb is darkened, or the brightness of the two bulbs of the car lamp is different, it must be replaced in time to ensure driving safety.

In addition, do not use direct contact with your hands when changing the bulb to avoid contaminating the bulb and slowing down the life of the bulb.

3. Scrub the lampshade frequently. When the car is driving on the road, it will inevitably splash and mud spots will be stained on the lamp cover of the car. Generally speaking, the lamp cover is made of special materials and has a good seal.

However, the lamp cover is dotted with dots of sludge, which greatly affects the beauty of the car and the effect of the headlights.

Summary. 4. The structure of the tail light wiring harness of the car is relatively simple, and you only need to unplug the wiring harness plug by hand. If it is not easy to pull out, gently pry it out with a small word change cone, and the wiring harness plug can be removed.

5. After the rear tail lamp cover is disassembled, you can remove the rear tail light, hold both sides of the rear tail light of the car with two hands, and then gently pull it out, and gently shake it while pulling, so that the rear tail light of the car is separated from the car body. The attention channel is not easy to be too large, the disassembly process of the entire car rear tail light is over, and the new car tail light cover can be replaced according to the reverse steps.

Hello, car professional analysis: Honda Lingpai tail lamp lamp cover is about 500 yuan.

The tutorial for replacing the tail lamp cover of the car is as follows: 1. After unlocking the main driver's door, open the main driver's door, and at the bottom left of the door trim panel, there is a button for the trunk to open the side state, press the button, and the trunk lid of the car will be opened. 2. After the backup cover is opened, you need to disassemble the lining cotton on the side of the tail light, pry open the buckle of the fixed lining cotton with a small word change cone, and peel off the lining cotton by hand.

3. There are three nuts to fix the rear tail lights of the car, take out the small wheel, match the No. 8 sleeve, and then disassemble the three nuts fixed on it one by one, and the disassembled nuts should be put away for installation.

4. The structure of the tail light wiring harness of the car is relatively simple, and you only need to pull out the wiring harness plug by hand. If it is not easy to pull out, gently pry it out with a small word change cone, and the wiring harness plug can be removed. 5. After the rear tail lamp cover is disassembled, you can remove the rear tail light, drag both sides of the rear tail light of the car with two hands, and then gently drag it out, and gently shake it while dragging, so that the rear tail light of the car is separated from the car body.

The attention channel is not easy to be too large, the disassembly process of the entire car rear tail light is over, and the new car tail light cover can be replaced according to the reverse steps.

The models of Honda Lingpai tail lights are T20 brake lights, T10 turn signals, T10 wide indicator lights, and H8 fog lights. Tail lights include reversing lights, rear fog lights, rear turn signals, brake lights, and width indicators. Damage to the tail light of the vehicle will affect the driving safety of the vehicle, and it needs to be replaced in time when it is damaged.

The lights mainly play the role of warning oncoming vehicles from behind.

The method of disassembling the tail light source wheel is:

1. Open the luggage compartment lid and disassemble the luggage compartment interior panel on the lamp side; dismantle 4 nuts and lamp assemblies;

2. Unscrew the lamp holder counterclockwise. Press the bulb and rotate it counterclockwise to remove the bulb from the lamp base;

3. Install a suitable spare bulb into the lamp holder. Replace the lampholder with the lamp housing. Rotate the lampholder clockwise to secure it;

4. Install the lamp assembly back on the vehicle and tighten the 4 nuts.

Lingpai lamp model is H11, headlight high beam model is 9005. With a body size of 4756mm in length, a width of 1804mm, a height of 1509mm and a wheelbase of 2730mm, the Guangqi Honda Lingpai is a compact car.

target="_blank">

style="border:1pxsolid#c6c6c6;"title=""

1.If you need to replace the bulb of Lingpai headlight, you need to remove the rear cover of the headlamp first, and then remove the clip that holds the bulb and then you can take off the bulb.

2.Lingpai is a strategic mid-level car under Guangqi Honda, with a body length, width and height of 4664 mm, 1750 mm and 1505 mm respectively.

3.The Lingpai is powered by a turbocharged engine with a maximum power of 90 kilowatts, mated to a CVT continuously variable transmission and a six-speed manual transmission.

Lingpai's headlight low beam model is H11, and the headlight high beam model is 9005. If the Lingpai headlight bulb needs to be replaced, you first need to remove the rear end cover of the headlight, and then remove the clip that holds the bulb and then you can take off the bulb.

As a special model created for the Chinese market, Honda's Lingpai has had a very good market performance since its launch, not only with good sales, but also with very high popularity. A few days ago, we learned from ** that Honda unveiled another new car, and the new 2020 Lingpai will be launched around July this year, and the face value is still very handsome, far exceeding the Toyota Corolla. It will be powered by a hybrid system with a fuel consumption as low as 4 liters.

Pacific Automobile Network] Lingpai luxury version of the rear trunk has lights, Lingpai body size length of 4756mm, width of 1804mm, height of 1509mm, wheelbase of 2730mm, Guangqi Honda Lingpai is a compact car.

Where is the Honda Lingpai trunk switch, the Lingpai trunk is automatically turned onHonda Lingpai can use the key to automatically open the trunk. As cars gradually penetrate into people's lives, people's expectations and dependence on cars are getting stronger and stronger. The trunk of a car plays a very important role in the actual use of the car, but this place is often a very neglected point in car maintenance and safety issues.

For the overall beauty of the trunk of the car, some car owners will choose to place a storage box in the trunk of the car to solve the problem of loose items. However, most of these boxes are made of plastic and do not have anti-slip functions. Because the miscellaneous things in the car are piled up in the storage box, resulting in a large mass, it will violently hit the interior of the cabin during the emergency braking, causing car noise, damaging the car is one thing, the key is that there are potential safety hazards.

And if the owner is accustomed to this way, then the storage box must be pressed against the rear seat of the car to prevent sliding during emergency braking.

If the items placed in the car are not fixed, then when braking or turning in an emergency, the items in the car will hit all positions in the car at a very fast speed under the action of inertia, and more seriously, they will hit the front windshield or directly cause injury to the human body. So you need to keep these items in the trunk of your car and secure them. It can be equipped with a trunk fixed net pocket, which is mostly made of nylon material, which is very elastic, and the mesh structure brings a larger stress area and buffer space, which is very practical for fixing disadvantages, and the shed is cheap and easy to buy.

Photo by Pacific Automobile Network Q&A).

The models of Honda Lingpai tail lights are T20 brake lights, T10 turn signals, T10 wide indicator lights, and H8 fog lights. Tail lights include reversing lights, rear fog lights, rear turn signals, brake lights, and width indicators. Damage to the tail light of the vehicle will affect the driving safety of the vehicle, and it is necessary to replace it when it is damaged and when it is noisy.

The lights mainly play the role of warning oncoming vehicles from behind.

The removal method of the tail light is as follows:

1. Open the luggage compartment lid and disassemble the luggage compartment interior panel on the lamp side; Dismantle 4 nuts and lamp assembly;

2. Unscrew the lamp holder counterclockwise. Press the bulb and rotate it counterclockwise to remove the bulb from the lamp base;

3. Install a suitable spare bulb into the lamp holder. Replace the lampholder with the lamp housing. Rotate the lampholder clockwise to secure it;

4. Install the lamp assembly back on the vehicle and tighten the 4 nuts.