How fast is a cat router switch? Masters and patient people please come in

In fact, the two gigabit ports of your switch, according to your configuration, are basically whatever you use the effect is almost the same, this switch is mainly used for network data exchange, and your external network is not optical fiber input, only 4m, and your routing is also a 100 Gigabit port, so no matter how your two Gigabit ports are connected, which one to connect, the effect is almost the same, Gigabit port and 100 Gigabit port in your environment, only there is your own LAN data exchange speed problem.

You said that your server is a game sharing host + charging system, and said that the rural information service station, I don't know what you are doing, your server is better to connect directly to the route, I don't know if the cat sent by telecom has a routing function, because the cat sent by telecom at home has a routing function, you can set up a hardware firewall, but I don't know much about this, I only know that the hardware firewall is better than the software firewall. Especially if you are engaged in Internet cafes to play games, because some games can not be played if the firewall is opened, and each machine is equipped with a killing software and firewall, which will affect the performance of the machine, thereby affecting the speed of the game, so, if you are engaged in an Internet café, it is best to engage in a hardware firewall, in addition to the server of the machine to install a restoration system or a restoration card, people have three urgency, go to the toilet, not to say.

I don't know how the performance of your router is, what the machine is used for, if you ** thing or do a server, maybe the performance of the router can't bring so many machines. The bandwidth also depends on what you are mainly using to surf the Internet, the functions and performance of the router, such as whether there is a rate limiting function, anti-virus and anti-attack, etc.

If your router is only a router of about 100 yuan, then you can take 11 computers to look at web pages, QQ and the like, you can't watch TV, you can't use P2P to watch movies, you can't ** things, and playing games may be very unstable. The server can be hooked to the router.

The server is connected to the Gigabit port.

In this way, the speed at which the computer can access the server will increase, but it has nothing to do with the speed of the Internet.

4M bandwidth can tow 11 units.

It should be noted that no one in the network maliciously occupies the bandwidth, and you can use network management software or limit the bandwidth of each IP in the router.

After resetting the route, you need to set it up again according to the broadband Internet access mode you access to the Internet.

There is a problem with your tracing, you are not moving the main route, you can only reset the route of one of the rooms, there should be only this room can not access the Internet, the network cable connecting the main route can be connected to the Internet, the network cable can be plugged into the WAN port, you can also plug in the LAN port, but the settings of the two ways of routing are different, and the key setting of the router after the route is to modify the LAN port settings.

If the upper-level router is then the second-level router will be changed to.

Here's how to get all your devices connected to the internet quickly:

The primary router connects the modem and the switch, and the primary router is configured to access the Internet to ensure that the network is networked. Enable DHCP on the primary route(All are enabled by default).

The sub-router in each room is connected to the switch, and the sub-router network cable is plugged into the WAN port, and the dynamic address Internet access mode is set (that is, the address assigned by the main route is automatically obtained to go online), and then the sub-router is configured to connect to the WIFI-related settingsCloseSplit-route DHCP

This way of surfing the Internet is the easiest, and the connection is also the fastest, without going through too many route translations and complicated settings.

There is no obvious difference between the fixed and automatic acquisition of the IP address of the sub-route, and it must be recorded after setting for subsequent maintenance to avoid confusion. Therefore, it is the simplest and easier to maintain that each room router uses a dynamic address to access the Internet (automatically obtaining the address assigned by the main route).

You don't need to set it, you can use the default settings.

When the network cable in each room is connected to the wireless router, is it better to connect the WAN slogan or the LAN port? It is good to set up to automatically obtain the IP address, and the secondary router of all rooms is connected to the WAN, and the IP is automatically obtained, which is normal.

There is a conflict in the reset (it must be the LAN port access, change to WAN).

Otherwise, there will be conflict.

The router has no network since it was restored.

That's because the default LAN port segment of a home router is the same, which forms a route conflict.

In your case, it is recommended to configure the following without changing the hardware investment and deployment location

The main router enables DHCP to assign IP addresses to all terminals in the home. All wireless routers change the LAN port network segment (it is required not to be in the same network segment as the main router, and the LAN port network segment of each wireless router is also different), and disable the DHCP function of the wireless router, and the incoming LAN port is not connected to the WAN port (so that the wireless router is basically set to a wireless access point mode); That's pretty much it.

If it is a broadband modem that needs to dial up, only the broadband modem can be connected to the wireless router, and the wireless router can be connected to the switch.

If it is a broadband cat connection wireless router that requires dial-up, set it up as follows:

1. Plug in the wireless router, don't connect the cat first, and connect the computer to any LAN port of the wireless router;

2. Enter the IP address of the router in the address bar of the browser (on the label behind the router), and enter the login username and password to enter the settings page;

3. Set up according to PPPoE (ADSL virtual dialing) mode, enter the Internet account and password;

4. Set the SSID, encryption method and password;

5. Save and restart;

6. After setting, connect the network cable from the cat LAN port to the WAN port of the wireless router.

The switch is not set up with filial piety, and the router needs to be set.

1. The bus of the broadband network is connected to the WAN port of the router, and the LAN port of the router is connected to the computer.

2. After starting the device, open the browser and enter it in the address bar to enter the wireless router late setting interface. (If you can't get in, please look at the nameplate at the bottom of the router or the router instruction manual, the default settings of different models of routers are different.) ）

3. An account and password to log in to the router appear in the settings interface, enter the default account and password admin, or refer to the manual;

4. After successful login, select the interface of the setup wizard, which will automatically pop up by default;

5. After selecting the setup wizard, a window will pop up to explain that you can set the basic parameters of the router through the wizard, and click Next directly;

6. Set up step by step according to the setup wizard, select the Internet mode, usually ADSL users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

7. Enter the password applied for from the network service provider, and go directly to the next step after the input is completed;

8. Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

9. After entering correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

Khan,It's only connected like this.,Routing even cats.,Cats connect switches.,Switches connect computers.,Otherwise, how can you go online?,Unless you use it alone, you can use it without a switch.,hoho

The route separates the network speed, and the network is relatively stuck