Can 4M Telecom Broadband Plus Cat Plus Routing Plus Switch Take Nine Computers? 30

Well, refer to the upstairs. Speed limiting software is a good idea.

4M bandwidth, 10+ people at the same time to read the web page, while playing games is estimated to be not a big problem...

Three cats + three routes are of course better than one cat + routes + switches.

Of course, the cost is also higher.

It's very simple, 3 cat exits have a bandwidth of 4m * 3 = 12m.

1 cat, how do you toss, it's still 4m bandwidth.

You should buy a high-end router that can allocate a certain amount of bandwidth to each person.

However, this is only a palliative solution, and the fundamental thing is that the external bandwidth is always small.

So, if you're going to open a small internet café, you need to see if there are any other networks you can apply for. I don't know.

If you're just using it for a home company, it's going to be coordinated. Accommodating each other.

It's too much trouble. Ask your nearest Internet café. Or look for someone who sells computers. At least you can get detailed information

If it's all wired computers (desktops), a cat plus a wireless router will do. There are 4 sockets in the back of the wireless router, and you can connect 4 network cables to get on 4 units. Once the wireless router is set up, there is no need to dial up.

You can connect to the Internet as soon as you turn it on. Set up the wireless router for instructions.

You can use cat+router or cat+switch It is recommended to use cat+router After the router is set up, you can directly connect the network cable to the Internet without dialing.

It can be conditionally achieved. One computer is used as the gateway server, the other computer is used as a client, and the computer acting as the server needs to add multiple NICs. The computer that is the server must be turned on to the other computer in order to access the Internet. Here's how.

The network card of the computer as a server is named "External Network", which is connected to broadband to ensure that it can access the Internet normally. The other piece is named the intranet and is connected to the switch. Set the IP address of the private NIC to a certain LAN, for example:

Then set the NIC to "Allow other network users to connect through this computer's Internet connection".

Once set up, the second computer will be able to access the Internet through the first computer.

If the first computer is installed with the software of the first server such as sygatge, you can flexibly control the Internet access of the second computer. You can choose according to your needs.

Dear telecom users, according to your description, the switch can not achieve two computers at the same time Internet access, the switch is an exclusive device, only the router can meet the requirements of sharing.

If you need to buy a machine, you can go to Anhui Telecom Tianyi store (hundreds of mobile phones are low on the whole network.

2 machines are a b

ip:,subnet mask:,default gateway:

DNS preferred: Point OK. Use a machine to establish an ADSL connection, and establish a good right health ADSL connection to select attributes Advanced:

Tick the box before allowing other network users to connect through this computer's Internet connection.

A machine dials up to access the Internet, and other machines can access the Internet (it's a switch, no way.) ）

It can't be realized, there is no function of automatic IP assignment, it is still an IP to buy a router now, and it is not expensive now, generally 70-80, just buy a good home-grade router.

One of them is a server, and a software is installed in the software, which is to be set in the browser.

It doesn't seem like it's possible, so you can buy a router.

Below the router, there is another switch setup method:

1. Line type: straight line 568B line sequence.

2. Network topology diagram: Extranet ---optical modem ---WAN) wireless router (LAN) - switch --- PC.

4. The switch does not need to be configured.

5. Automatically obtain the address for PC.

The specific process:

1. Connect the cat to the power supply and the other end of the ** line, connect a network cable 2, connect the network cable on the cat to the WAN port of the router (usually blue), then you can connect three computers and a switch from the other four ports of the router (you can also connect only one switch and connect all the computers to the switch).

3. After connecting the computer and connecting to the Internet cable, enter the router IP, usually or, and set up the ADSL dial-up OK.

The ADSL modem is connected to the external network, the WAN port on the router is connected to the ADSL modem, the UP-Link port on the switch is connected to any port on the router except the WAN port, and each computer is connected to the rest of the ports on the switch!

The cat comes out to connect the router - out of the four wires to connect 3 computers and a switch, the switch is connected to two, so that you can use it directly without setting.

OK. But be sure to set it up correctly.

I don't recommend you do this. Because it requires specialized knowledge to set up, if you are not careful, you will not be able to do anything.

If you want to access the Internet on multiple computers at the same time, you just need to connect the router to the network cable that can access the Internet and simply set it up.

Thank you for your question.

Yes, the cat router that comes with telecom supports watching TV and computer together.

If the telecom is a PON modem, it can be realized, because the PON modem has three LAN interfaces, and the ITV needs to be directly connected from the cat to the set-top box to realize the smooth connection between the set-top box and the network ITV service. Broadband Internet access directly from the LAN port of the cat to the router to the PC computer Internet access. In this way, ITV and broadband can be used at the same time, if the ADSL modem has only one LAN interface, only a switch can be added to realize the simultaneous use of the two networks.

Yes, the cat itself is a combination of a switch and a router.

First of all, I'll tell you what your problem is,After the cat comes out, only one is allowed to dial up the Internet,If the router is not set,Then it only plays the role of a signal branch,Then the two computers who dial first can get on,The other one will only stare at the part (the so-called first strike is strong,The second hand suffers)。

Another one of your connections is too troublesome, the cat comes out and connects directly to the router, because you are using a wireless router, after setting the router to automatic dialing, because it is a wireless signal, you have no problem even connecting a few machines to the Internet (in principle), unless you have many machines, no wireless network card, long distance and other reasons, then connect a switch under the router, and the problem can be solved.

I want to know if your second computer can access the Internet normally without dialing If it can, it means that your router has been dialed or your first computer has been dialed up, in fact, the correct connection is to follow the upstairs said optical modem-router-switch like this.

The normal words are: the route is connected to the optical modem, then the switch is connected to the router, and then each computer is connected to the switch; Depending on whether you are a static IP or dial-up Internet access first set up the router, if there are more machines, you can also divide a little more switches, but you must let several switches are connected to the route, and the light modem is connected through the route! That's it.

The correct connection method is optical modem.

Routers are connected to switches.

Behind the switch, you want to connect the route, and the switch can be.

First use the cat to connect the router, then use the router to connect to the switch, and then you can use the three ports of the router to connect to three computers, and then use the three ports of the switch to connect to three computers.

Not bad, I hope you do.

Why do you have to dial the number, let the router dial just can't do it, and the computer can't be used when it's turned on.

You have several account numbers.

Separate accounts should be able to connect to broadband at the same time.

Hello, you can use a switch to form a LAN for use, and the number of computers supported depends on how many ports your switch has.

Let me tell you, the speed of the four-megabit broadband** cannot reach 800. At most, it's a speed of 512k. And then your second question, this is my most professional