How often do Toyota Camry brake pads need to be replaced?

Hello, depending on the usage of individuals, generally about 40,000.

It takes about 1 hour to change the brake pads. According to the normal driving situation of the car, the general front brake pads need to be replaced once after 3-50,000 kilometers of driving, and the rear brake pads need to be replaced after 6-100,000 kilometers, and the brake pads can also be replaced by themselves, and the tires need to be disassembled, which is more troublesome, and it takes about 1 hour to replace a set of brake pads, which is time-consuming and labor-intensive.

Specific operation of changing brake pads:1. To replace the brake pads, you need to lift the car and remove the tires;

2. Remove the screws of the brake caliper, remove the brake caliper, and remove the old brake pads;

3. Push the brake piston back and install the new brake pads;

4. Install the brake caliper back, screw the caliper screws to the required torque, and then install the tires back;

5. After the brake pads on both sides are replaced, you will find that the brake oil in the brake oil pot is overflowing, in this case, you need to step on the brake several times to keep the liquid level between max and min.

The front brake pads are about 30,000 kilometers to replace, and the rear brake pads are about 80,000 kilometers to replace, of course, this is only an approximate direction, according to each person's different car habits, and the braking system of each car is also different, so the replacement time should be determined according to the degree of wear, but it is best not to exceed this number.

Toyota Camry brake pads do not have a specific replacement cycle, and the thickness is worn to the original 1 3 and need to be replaced. Automobile brake pads, also known as automobile brake pads, refer to the friction materials fixed on the brake drum or brake disc that rotates with the wheels, and the friction lining and friction lining bear external pressure to produce friction to achieve the purpose of vehicle deceleration. Here's how to replace the brake pads:

1. Before replacing the brake pads, you should open the lid of the brake fluid reservoir in the engine compartment to see the height of the brake fluid page, if the brake fluid page is above the highest limit, you should suck out some brake fluid to prevent the brake fluid from spilling out during the replacement process;

2. Prepare the brake pads to be replaced and remove the wheels where the brakes are located. In the process of dismantling, it is necessary to avoid scratches on the rim;

3. Remove the bolts of the brake caliper with a wrench combined with the sleeve, and then remove the brake pad (if there is a brake induction line, the brake induction line should be removed first). Observe whether the brake pads are overworn, or cracked, and replace them in the next step;

4. Since there will be a lot of sand or mud in the brake caliper, it should be cleaned with a rag, and then applied silencer paste to prevent abnormal noise when braking;

5. Press the piston to the position where the piston pressure pump cannot be pressed, then install the brake pads on the brake caliper, install the new brake pads in place (those with brake induction lines should also be installed), tighten the guide bolts, and the installation is completed;

6. After installation, cover the lid of the liquid storage tank, enter the car and press the brake plate a few times, and reset the brake. Then observe the height of the brake fluid, which should be within the appropriate height range;

7. Test drive after changing to check whether the braking effect is reflected.

Toyota Camry brake pads are in normal use for more than 30,000 kilometers, and there is no need for a fixed replacement cycle. Toyota Camry uses original brake pads.

Toyota Camry Camry Twin Engine Brake Pad Replacement Tutorial.

Note: The rear wheel of the Toyota Camry adopts an electronic parking brake motor, the brake cylinder can only be retracted by the trip computer, and the brake pad can only be replaced after the brake cylinder is retracted. The front brake cylinder can be removed directly with a tool and does not need to be controlled by a trip computer. Take the wheel below, for example.

Connect to the vehicle via a computer and select "Open Rear Brake Cylinder" on the brake pad replacement setting screen. After about 5 seconds, you can hear the rear wheel cylinders splitting. When this god friend beams, the parking brake motor is retracted.

Note: Be sure to open the lid of the brake oil can, as brake fluid may flow back due to pressure shocks caused by the retraction of the driven cylinder. )

Remove the two screws on the brake caliper spine first. If the cylinder is not completely detached, pry it open slightly with a flathead screwdriver.

Then open the caliper cover and place the new brake pads. The side with the text logo faces outward, and the smooth side without text faces inward.

After installing the new brake pads, select "Turn off the rear brake cylinder" on the setting interface of the trip computer, and the brake motor will be pushed out and reset after about 5 seconds.

Millions of car purchase subsidies.

Camry brake pads are recommended to be replaced every 4-60,000 km. Brake pads are also called brake pads. In the braking system of the car, the brake pad is the most critical safety component, and the brake pad plays a decisive role in all the braking effects, so a good brake pad is the protector of people and the car.

How can I tell if a brake pad needs to be replaced?

1.Look at the thickness.

The easiest way to do this is to look at the dashboard prompts. When the brake pad indicator light is always on, the brake pad needs to be replaced in time. Usually we can observe the thickness of the brake pads, so that we can have an idea of it.

Under normal circumstances, the thickness of brand new brake pads is about centimeters, and if your brake pads are less than centimeters, you should consider replacing them. Due to the angle of your own **, there will still be errors, and the inner brake pads are sometimes difficult to see, so it is best to ask the master to take a look at the maintenance every time you go to the 4S shop.

2.Listen to the sound.

Measurement is the safest square hole Zheng Qing method, but there are some phenomena that can indicate the degree of wear of the brake pads. When you hear the squeak of metal friction when braking gently, it may be that the brake pads have exceeded the limit of use, so be sure to check them as soon as possible.

3.Feel the intensity.

When you press the brake pedal, you need to press deeper to achieve the original braking effect, and the braking effect is significantly weakened in the first half. This phenomenon may be caused by problems with brake pads, brake lines, etc. There are many reasons for this.