Urgent!! How to get rid of glass mold

Wipe the glass with a towel dipped in beer or warm vinegar to quickly remove dirt from the glass.

Apply some chalk ash or gypsum powder to the glass first, and wipe it with a cloth after drying.

Fill the basin with some water, pour a little shampoo and mix it, and use it to wipe the glass, it will look extra clean and bright.

In winter, the surface of the glass is easy to frost, and it can be wiped with a cloth dipped in concentrated salt water or liquor, and the effect is very good.

The dirt on the glass can be wiped clean and bright with a cloth or silk dipped in toothpaste.

Take two pieces of cloth, one dry and one wet, and wipe both sides of the glass with a damp cloth first; Then use a dry cloth dipped in a small amount of liquor and wipe the glass vigorously to make it clean and bright.

Slight mildew can be removed with edible white vinegar, and serious mildew or even rainbow discoloration needs to be washed off by buying a professional cleaning agent, such as glass buster, which is a special cleaning solution. It's good for you to let the manufacturer express it to you.

Wipe the glass with hydrofluoric acid in a ratio of 1 to 7 and then rinse it with clean water, and then dry the glass in the shade, but be careful, hydrofluoric acid is a strong acid, and you must be especially careful when using it to prevent burns!

The easiest thing about glass is that you can wipe it with a damp cloth, it's not very difficult!

Just wipe the surface with a 5% hydrofluoric acid solution.

Rub it with hot alkaline water, preferably with boiling water beforehand.

Glass Mold Spot Cleaning Method:

Ingredients: white vinegar, salt, scouring pads, glass bowls, chopsticks.

Step 1: Pour the white vinegar into a glass bowl (white vinegar has a bactericidal effect).

Step 2: Then pour salt into the glass bowl (salt also has a bactericidal effect).

Step 3: Use chopsticks to stir the white vinegar and salt well.

Step 4: Use a scouring pad dipped in the homemade solution and carefully wipe the mold from the glass.

Step 5: The mold has been removed.

Rinse with clean water and then wipe the glass with a little laundry detergent to remove stains, mildew, etc. on the glass. Finally, wipe it off with water.

1.Glass mold remover is a newly developed glass treatment solution.

Glass mold remover.

Scope of application] is suitable for all slightly moldy glass products (such as color red, mildew spots, water marks on the glass after edging).

How to use] Use a cleaning cloth or sponge dipped in a little bit of this product to wipe a few times on the moldy place of the glass, and then rinse it with water, you can make the moldy product look new and get your satisfactory effect.

This product has no impact on people and the environment, is the most ideal and environmentally friendly product on the market, and the simple operation is the most ideal and affordable choice for individuals and enterprises.

2.Stripping liquid.

Scope of application] is suitable for glass products with long mold time, paper pattern and paper print.

How to use] put the glass into the original solution to soak for 5-8 minutes, and then rinse with water, the effect is as clean as new, this product has no impact on people and environmental protection, is currently on the market environmental protection series products.

3.How to use it in common (glass cleaner):

Scope of application] Efficient and rapid cleaning of glass, no need to pass through water, no traces, can make the glass surface crystal clear, can also be used for toilet equipment, tiles, mirrors, stainless steel, etc.

How to use] a, after mixing this product with water at 1:20, spray it on the glass counter with a watering can, and use a soft cloth or glass scraper on the surface of the glass exterior wall.

b. If there is granular dirt on the surface that needs to be cleaned, it needs to be washed away or shoveled off first, and then scraped with a soft cloth or glass to avoid scratching the surface.

c. This product is suitable for computers and phosphor screens, and needs to be diluted with water (1:10) before use.

The question is too serious.

Ask what medicine to wash.

Question** Some buy.

Send a question and take a look.

Then you use a glass cleaner.

Classification of glass mold conditions.

1.White mist, white spots: the slightest mildew on the glass surface due to storage time, air humidity or glass quality issues.

2.Rainbow: When the white fog and white spots appear for a long time and are not treated in time, a rainbow will be formed, and the mildew at this time only stays on the surface of the glass and does not corrode into the glass.

3.Sulfurization: The appearance characteristics of glass mildew are the same as those of slight mildew, but the alkaline mildew components on the surface of the glass have corroded into the glass, which is a severe mold.

4.Paper printing: Like sulfurization, mold is on the outside and inside of the glass, which is a serious mold.

Glass mold removal method.

1. Glass mold remover.

It is suitable for all mildly moldy glass products (e.g. colored red, mildew spots, water marks on the glass after edging) and the initial stage of severe mildew (e.g. sulfurization, paper printing).

How to use: Scrub the glass once or twice with a cleaning cloth or sponge dipped in some of this product, and rinse it off with water immediately, you can make the moldy product look new and get your satisfactory effect.

2. Buy a small bottle of acetic acid, take a small basin, add 2 kg of water to the basin, then pour the acetic acid into the basin, and then stir well. Put the glass bottle to be cleaned into the basin, fill the bottle with an appropriate amount of water and acetic acid mixed liquid, gently shake the bottle for about 1 minute, pour out the water in the bottle, and wash it again with water.

Glass mold is mainly caused by the formation of silicates on the surface of the glass when it becomes wet. It is usually made of silicate decomposition inhibitors as anti-mildew agents, i.e., hydroxides with high organic elements with strong electric fields or salts that are easily hydrolyzed. Such as the use of azncl2 ammonia solution or 2-methacrylic acid.

Mould has already appeared, and it can be cleaned with a weak acid or a weak saline solution. And keep the glass dry afterward.

Wash with alkaline detergent, then wash with clean water and wipe with a dry cloth. Finally, spray the glass with an antifungal agent.

Use washing essence, if it doesn't work, you can use toilet cleaner. Then wash with water.

After years of research, the glass factory has developed a glass savior through foreign branch experts, and the phenomenon of glass, marble panalkali, color red, whitish, crystallization, paper print, mildew, whitening, etc., is the only one that can be fully effective in the above problems of glass, and the cost of dealing with it is very low. Need to call Fuxin Photovoltaic Glass Factory 13194188188 Chen.

Very simple, pour a little 84 disinfectant into the glass bottle with mildew, gently shake, after 5 minutes, the mildew will be removed, and then rinse with water. Washing with 84 disinfectant has two advantages, one is that it can wash the glass bottle, and the other is that it can be disinfected, because there must be bacteria in the glass bottle with mold.

toothpaste, soot, salt. These three are the most practical and effective, add less water when you use it, rinse it with water after brushing, and then disinfect it with boiling water.

Buy a test tube brush and pour some boiling water into it to brush.

Decorate with water and mix with vinegar, vinegar can break down mildew.

Are you using the bottle?

Use an oak soft towel dipped in a little vinegar, wipe it lightly like slag, or spray it with alcohol, and then wipe it in the morning, or pour it on the glass with dry laundry detergent, and then wipe it with a soft cloth.

The following points can be used to solve glass mold:

1. Hydrofluoric acid solution is 1:50 ratio to clean the glass surface and rinse with water.

2. Wash the glass surface with citric acid in a ratio of 1:50 and rinse it with water.

3. Oxalic acid 1:50 ratio to clean the glass surface and rinse with water.

The above methods can clean up mildew or impurities on the glass surface, and in severe cases, the concentration can be increased or glass mold remover can be used.

2. Then pour salt into the glass bowl (salt also has a bactericidal effect).

3. Use chopsticks to stir the white vinegar and salt well.

4. Use a scouring pad dipped in a homemade solution and carefully wipe the mildew on the glass.

5. The mildew has been removed.

Mold can be removed with Xinqige antimicrobial agent, and it will not become moldy again after trial.