Liquefied gas can t catch fire, please come in and take a look at the specific description! Thank yo

Very simple. The first is to determine the fault to see if it is a water pressure problem or a fire problem. Method:

Remove the water heater cover, press the lighter, and if it doesn't catch fire, light a lighter with your other hand to see if you can light the water heater. If the lighter can be lit, it means that the problem is still with the igniter; If the lighter also doesn't light up, the problem is with the liquefied gas. When in the ignition state, it has no relationship with water pressure.

If the water heater cannot be ignited during the discharge process, it is a problem of water pressure. If it's a matter of the igniter. One is that the voltage of the new battery itself is insufficient due to the storage of the new battery for too long; One is that the ignition electron gun was accidentally touched, resulting in a change in the position of the electronic ignition gun, which could not be ignited normally.

My personal opinion is more inclined to replace the battery with insufficient voltage. Although it was fired, it was not enough to ignite the liquefied gas.

Hello landlord, I have also encountered this situation of you, it is the ignition that the device is broken, and the spark cannot be beaten, so it can't be repaired, you can't repair it, it is to be replaced, but just change a small part, find someone to repair it, a few dollars. I definitely don't have that thing in my house. Hope it helps!!

I also ran into the problem you mentioned last summer.

It went out in a few minutes because the water pressure of the tap water was too low. (The air pressure in the coal pipe leading to the water heater is greater than the water pressure, so you can't catch fire all the time.) ）

You first turn off the valve of the gas tank, release the snorkel and your gas, and then connect it to light the fire. (Of course, it is very troublesome to do this every time) In addition, the fire power is adjusted up in the water heater.

Solution: 1. How many liters of water heater is yours, and at least 7 liters of water heater should be bought where the water pressure is at the bottom.

You'll need to change to a 7-litre water heater or install a small booster pump.

2. Electricity is not very cheap now, why not buy an electric water heater?

Causes and treatment methods for gas stoves not catching fire:

1. There is no gas, usually everyone has a bottom about this, but some people may be more careless, or the homework is busy, and often forget, so when the stove is not on fire, the first thing to check is whether there is still gas. Solution: If the bottled gas is out of gas, it is necessary to add gas, if it is pipeline gas, ensure that the gas valve switch is turned over.

2. The battery is out of power, which is a question that is usually briefly encountered, and it is also a question that everyone attaches more importance to, and if you find that the light is not on fire and there is no clattering sound, you must check whether the battery is charged.

3. Poor circuit touch, this is a very simple and negligent question, but it is often encountered in many old users, mainly to check whether the positive and negative poles of the battery box are rusty, and whether the line is badly touched.

4. The gas stove is a kind of stove, which is mainly used to supplement the lack of air during combustion by providing natural air in the gap between the stove and the upper cover, so as to promote combustion and reduce the generation of carbon monoxide and nitrogen oxides. The air intake mode of gas stove is divided into upper air inlet, lower air inlet, full air intake, etc., which can be divided into multiple types according to different classification standards.

Let's take a look at your liquefied gas stove first, is the ignition mechanism out of battery? If the electronic ignition mechanism can ignite normally, but the fire cannot be ignited, it may be that the gas supply of the pipeline is insufficient, or your gas outlet is blocked.

What to do if the gas stove can't catch fire The gas stove is one of the essential kitchenware for kitchen cooking, in the process of cooking, people often encounter the phenomenon that the gas stove can't catch fire, the gas stove automatically turns off, etc., and mastering the working principle of the gas stove can make us better check and eliminate the fault.

How a gas stove works.

When the knob is pressed and a small fire is ignited, the thermocouple is heated by its flame, creating a thermoelectric potential. The thermoelectric potential is introduced into the electromagnetic coil through the wire, and the magnetic field is generated to make the solenoid valve suck, the gas valve is opened, the combustion path is opened, and its normal combustion is maintained, once it encounters the overflow of strong wind or soup, etc., extinguishes the flame, the thermoelectric potential of the thermocouple quickly drops to zero, the coil loses power, the solenoid valve fails, and the valve is quickly reset under the action of the spring, and the valve closes the gas path, terminates the gas supply, and ensures safety.

The reason why the gas stove does not ignite the fire.

Clause. First, if there is no gas, if the gas stove does not catch fire, the first thing to check is whether there is still gas, if not, you must add gas.

Clause. Second, whether the battery has electricity, when it is found that it is not on fire, it is necessary to check whether the battery has electricity, if not, you only need to replace the ordinary No. 1 battery.

Clause. 3. Poor circuit contact, mainly to check whether the positive and negative poles of the battery box are rusty, whether the line has poor contact, if so, the rust needs to be removed, and the line is accurately connected.

Clause. Fourth, overpressure protection, many gas stoves have overpressure protection function, once the overpressure will not start, then it is necessary to change a pressure reducing valve to try.

Clause. Fifth, the pipeline is blocked, once the pipeline is blocked, it is necessary to check the gas valve, generally speaking, you can smell the smell of coal and the gas stove is not on fire, it is likely to be a gas blockage, then you need to dredge the pipeline.

Clause. Sixth, the micro switch is damaged, the micro switch is a very small place in the gas stove, but it is more difficult to repair than the usual faults, generally speaking, it is not recommended that the owner repair it himself, this is a fine, professional work, it is best to ask a specialist to solve.

Clause. 7. The ignition needle is dirty, the kitchen is easy to be dirty, especially easy to be contaminated with oil, etc., the gas stove is placed for too long, and the ignition needle is easy to be stained by the oil, so you need to clean the ignition needle and then try to ignite.

Clause. 8. The ignition needle is not properly positioned, if you want to ignite the fire, the gas stove has certain requirements for the distance between the ignition needle and the fire cover, once the distance deviates too much, it will cause the gas stove to not ignite, generally speaking, the distance between the ignition needle and the fire cover is 4-6mm, and it is necessary to aim at the fire hole.

Clause. 9. The gas stove has a high-voltage line and its joint, once the high-voltage line is aging, it is easy to make the gas stove can not catch fire, at this time, only need to add a set of high-voltage protection, which should be observed more in ordinary life.

The reasons why the liquefied gas stove cannot catch fire are generally as follows:

Cookers are generally divided into liquefied gas, coal gas, natural gas (or air mixture), because natural gas is relatively clean, there is little carbon, and the composition of liquefied gas and coal gas is relatively impure and easy to carbonize.

Note: Protective cotton gloves or plastic gloves must be worn before hands-on inspection of the liquefied gas stove.

One of the reasons: the battery is insufficient, the phenomenon of two burning eyes at the same time suddenly can not ignite, follow the line of the lighter, on the opposite side of the lighter switch (near the wall) is easy to find a No. 1 battery, replace the battery.

Reason 2: carbon clogging the eye, the phenomenon is that the eyeburner that is often used on the outside can not catch fire, as long as the detachable eyeburner part is cleaned with toothpicks and other items, rinse with water. (Cooking spills are treated in the same way and dealt with in a timely manner).

Reason 3: Rust clogs the burning eye, the phenomenon is that the burning eye that is not often used on the inside can not catch fire, the detachable part must be cleaned with a toothpick, the stove buckle is knocked over, and the rust can be poured out.

Reason 4: improper adjustment of the damper, the phenomenon is that the fire is big or small, sometimes it cannot be hit, and it is necessary to go to the maintenance point for consultation and on-site learning on different types of cookers and different brands of cookers. There is a kind of stove with a small screw at the air supply of two dampers, if one of them is loose, the other is not easy to ignite.

Reason 5: For unknown reasons, please repair the brand professional maintenance point.

The above situations refer to the stove under the age of five years, if the stove more than five years old has the above situation, after treatment, it still does not catch fire, it is recommended to replace it.

Summary. Hello Oh Liquefied gas is just filled and can not ignite is possible from the gas valve to the stove There may be air Oh It should be a few more times when ignition, the air in the trachea can be discharged to ignite, and then it is necessary to test whether the trachea and valve are in good condition, and also to see if the ignition device has sparks, whether the battery power can be used, in short, it is fire and other gas, don't wait for fire.

Why can't the liquefied gas catch fire when it's just filled?

Hello Oh Liquefied gas is just filled and can not ignite is possible from the gas valve to the stove There may be air Oh It should be a few more times when ignition, the air in the trachea can be discharged to ignite, and then it is necessary to test whether the trachea and valve are in good condition, and also to see if the ignition device has sparks, whether the battery power can be used, in short, it is fire and other gas, don't wait for fire.

You can let go out a little bit and reduce the pressure.

Liquefied gas can not catch fire, need to clean the stove, dredge the pipe, replace the battery, high-voltage line, pressure reducing valve, so that the liquefied gas can be used normally, if the ignition needle of liquefied gas has a spark, liquefied gas ** normal, you should adjust the distance between the ignition needle and the fire cover, so that it is kept at about five centimeters.

1. Clean the cooktop

If the liquefied gas does not ignite, it may be that the ignition needle is dirty and clogged by the kitchen oil, and you need to turn off the liquefied gas, clean the cooktop, clean the ignition needle and the dirt on the cooktop, and then turn on the liquefied gas again to resume use.

2. Dredge the pipeline

The gas supply pipeline of liquefied gas is blocked, and there will be a situation that it cannot catch fire, so it is necessary to close the valve of liquefied gas, remove the pipeline for cleaning, and dredge it, or only replace the pipeline of the new group cavity for installation.

3. Replace the battery

If the battery runs out of power, the liquefied gas will not catch fire, and the liquefied gas can be replaced with a new battery and then turned on again.

4. Correct the position

The distance between the ignition needle of the liquefied gas and the fire cover is greater than six centimeters, which will cause the cremation of the ignition needle to be unable to contact the liquefied gas, and naturally it will not ignite, so that the ignition needle should be moved to the direction of the fire cover, so that the distance between the two is between four centimeters and six centimeters.

5. Replace the high-voltage line

The ignition switch of liquefied gas is connected with a high-voltage line, if the high-voltage line is aged, it will make the liquefied gas not ignite, at this time, the high-voltage line should be replaced, and a high-voltage protection device should be installed outside the high-voltage line to prolong the use time of the high-voltage line.

6. Replace the pressure reducing valve

In the process of using liquefied gas, for the sake of safety, the overpressure protection function will be set, if the pressure of the liquefied gas is too large, the protection device will be activated, resulting in the liquefied gas can not ignite the fire, at this time, the protection device should be restored to its original state, and a pressure reducing valve should be changed to control the pressure of the liquefied gas.

Summary. 1. The liquefied gas stove cannot catch fire, probably because the liquefied gas is used up, and only the liquefied gas tank needs to be replaced. 2. Under the condition of ensuring that the liquefied gas is sufficient, observe the sparks when the gas stove is ignited, whether the sound is soft and weak, if so, the battery needs to be replaced in time.

3. If the spark is crisp and powerful, but it does not ignite, it may be that the nozzle in the stove is blocked during use. Remove the fire splitter cover and use a thin iron wire to pass through the nozzle hole, and then put it back into the fire cap to re-ignite. 4. If the air volume is too large, resulting in too much airflow from the fire hole, and the impact of the electric spark, there will also be no ignition, so you can try to adjust the damper.

Liquefied gas can't be hit.

1. The liquefied gas stove cannot catch fire, probably because the liquefied gas is used up, and only the liquefied gas tank needs to be replaced. 2. Under the condition of ensuring that the liquefied gas is sufficient, observe the sparks when the gas stove is ignited, whether the sound is soft and weak, if so, the battery needs to be replaced in time. 3. If the spark is crisp and powerful, but it does not ignite, it may be that the nozzle in the stove is blocked during use.

Remove the fire divider cover and use a thin withered iron wire to pass through the nozzle hole, and then release the excavation suspect back to the fire cover and re-ignite. 4. If the air volume is too large, resulting in too much airflow from the fire hole, and the impact of the electric spark, it will also judge that the loser will not catch fire, so you can try to adjust the damper.

Solution: If there is no coal stove, the bridge ant should be added. The reason why the liquefaction stove cannot be used is 2, the needle is dirty The kitchen is very dirty, especially easy to be contaminated with oil, etc., and the coal stove is placed for too long, and the needle is easily stained by oil.

The reason why the liquefied gas stove does not catch fire.

1.The micro switch is damaged.

At this time, there is a small area in the gas stove, but it is more difficult to repair than the usual breakdown, and in general, it is not recommended for the owner to repair it himself.

Solution: The micro switch of the gas stove is damaged, this is a delicate and professional job, and it is best to ask a professional person to solve it.

The reason why the liquefied gas stove does not catch fire.

2. Whether the battery has electricity or not.

This is the most common problem, and it is also a problem that people are generally concerned about, and when they find that the ignition is not ignited, they should check whether the battery is charged.

Solution: If the gas stove battery is not used or used up, you only need to replace it with an ordinary No. 1 battery.

The reason why the liquefied gas stove does not catch fire.

3.Improper placement of the ignition needle.

If you want to ignite the fire, the gas stove has certain requirements for the distance between the ignition needle and the fire cover, and once the distance deviates too much, the gas stove will not ignite.

Solution: Generally speaking, the distance between the ignition needle and the fire cover is 4-6mm, and the fire hole should be aligned.