The wireless router cannot access the Internet, and the IP address is abnormal

There is a label on the reverse side of the wireless router that will have the login IP address of the route and the default administrator and password, if you have changed it before, and now you have forgotten it, or it has always been the correct solution, but you can't enter the routing ......Please restore the default factory value of the router, press and hold the reset key for about 10 seconds, look at the indicator light in front of the route, the indicator will bounce and restart, and then enter the route, the default of the general route is or.

According to the problem situation you described, "the server page of the wireless route cannot be opened", either you made a mistake with the login page of the route, or there is a problem with the router, about", this IP address is not assigned to the PC IP address of the route, that is, after the client does not find the DHCP server, it will automatically configure an IP address for itself, indicating that there is a problem with the DHCP server of the route, you first set to automatically obtain the IP address, and then open cmd, Enter ipconfig all to see if the information such as ip, dhcp, dns, gateway and so on is correct, if the ip address is the beginning of the above, it means that the gateway dhcp server is working abnormally.

After the factory value of the route is restored, ping the route to see if it can be pinged, and then ipconfig all to see if the gateway can be found, and the IP address ...... is correctly obtainedIf you can't, please change the router to troubleshoot!

Another point, when you connect the routing configuration of a stand-alone machine, if the WLAN port does not work, try to change the LAN port, if the LAN port does not work, try to change the WLAN port, I hope mine can help you! Good luck with a speedy solution!

First set your computer IP to automatically obtain, and then use the network cable to connect with the wireless router LAN port, enter the routing IP on the IE address strip to set the route, if you don't self-route the IP can: run, cmd enter, and then ipdonfig all to see the gateway and dns This should be your routing IP, and you can surf the Internet after setting.

The router is a bridge between computer networks, but in the process of connecting the network to the network, the configuration of the router plays a key role, so do you know what to do if the IP address of the wireless router is invalid? Here are some relevant information about the invalid IP address of the wireless router I have compiled for your reference.

Workaround for invalid IP address of wireless routerWhen I type it in my browser, it shows that the webpage is inaccessible.

Right-click on the neighborhood and select Properties.

Right-click in the local connection.

Select Properties, and then select Internet Protocol.

Click Properties to see if Automatically get IP address is set to automatically get DNS server address, if not, click Automatically get.

Press OK to save the settings, now go to the browser to try to open the router settings interface, if it doesn't work, press the reset button of the wireless router until the indicator light lights up three times, and then open the router settings interface, then you should be able to enter, enter the username and password, note that the reset of the username and password are not set by you, but are anmin, (the username and password are) so that you can enter the router to start setting.

1.What should I do if the IP address of the wireless router connection conflicts?

2.What should I do if the router prompts that the address is invalid.

3.What should I do if the IP address of the wireless router cannot be opened?

4.What should I do if the wireless network of the router cannot obtain the IP address?

There are several possibilities:

1. Check your access method. If it is a PPPoe access, check whether your username and password are entered correctly; If it is a static access, check whether the IP and DNS settings are correct.

2. Check whether there is a problem with the connected port or network cable.

3. It's best to restart the router after the setup is complete.

It depends on your original network cable, whether it is set to dynamically obtain or static IP, and then choose one according to this in the route, there will be no failure to obtain IP!

Enter the router and look at the items inside, there is one DHCP service. The service inside must be turned on, otherwise, your computer and mobile phone will not automatically get the IP address.

First of all, you have to confirm that the wireless router is already on the network, now the home is generally dialed up through PPPOE to access the Internet, this in the wireless router settings must be understood first, and then take the network cable to connect to the book or desktop, test whether the Internet is successful, in addition, the router needs to turn on the DHCP service, in order to make the mobile phone, this book, etc. use wifi to surf the Internet, what you said is because the router did not open the DHCP server.

It is estimated that the wireless router you bought does not support PPOE dialing, or you have not set it up correctly; Or if the carrier provides a static IP, please reset the wireless router according to your original computer settings.

Restart the route

Then disable the wireless card and then enable it again.

Looking at the routing configuration, the main focus is to check DHCP and automatically obtain the address.

Have you solved it? I'm asking for advice right now.

The system detects that the IP is abnormal, and access has been disabled, which is caused by a setting error, and the solution is as follows:

1. First of all, find and open the "Guess the Run" window (win+r) on your computer. Enter " and click OK.

2. In the "Local Group Policyr" that opens, "User Configuration - Management Template - Network - Network Connection".

3. In the window on the right side of the "Network Connection" option, find "Enable Windows 2000 Network Connection Settings for Administrators".

4. Double-click to open the key to enable for administrators, in the pop-up window, check "Enabled" and then press "OK".

5. Go back to the window on the right side of "Network Connection" and double-click to open "Disable access to the properties of the LAN connection component".

6. Finally, select "Enabled" in the pop-up menu and press "OK". Ordinary users cannot change the IP address at will.