How to set up a wireless router to specify Internet access

2. Enter the correct username and password to enter the router management background.

3. We need to check the existing IP and the corresponding MAC address bar first. Click "DHCP Server" on the left, select "Client List", and write down the corresponding IP and MAC addresses displayed on the right.

<>5. Enter the correct corresponding MAC and IP address on the right, then select "Status" as "Effective", and then click the "Save" button to save.

1. Password setting: (take tp-link as an example).

Enter the browser to enter the router login page.

Enter your username and password to open the router settings screen.

In the "Wireless Parameters" section on the left, click "Basic Settings".

Fill in the SSID number (preferably more than 8 characters), set the "Frequency Band" 11, and select the "Mode" 54Mbps (

Turn on the wireless function (tick).

Allow SSID broadcast (ticked).

Enable the bridge function (unchecked).

Turn on the security settings (ticked).

Select Security Type: wpa-psk WPA2-PSK Select Security Options: WPA2-PSK

Select "Encryption Method:" TKIP

Fill in the PSK password, the shortest is 8 characters, complex characters and numbers.

Group key update cycle: 30

Then click "Save".

On the left "System Tools", click "Restart Router".

2. Address binding.

Just clone your mac address to your router、、、 and run -cmd-ipconfig all to see the mac address in terms of mac address viewing. After you go in, click on the security settings,,Write down the physical address you want to surf the InternetMAC address is the physical address,,The physical address can be。。 List of DHCP servers --- clients.

According to the computer name of the computer,,, copy with CTRL+C,,After adding it,,Turn on the firewall (firewall master switch) --- to the security settings ---firewall settings)--check this box.。。 Mac, that also ticks the mac, and you choose according to your own actual situation. That is, if your MAC address is written in the physical address of the Internet to be accessed, then you can choose --- only allow the MAC address that has been enabled in the MAC address list to access the Internet, otherwise choose another one, so that it is good to save.

Enter the router wireless settings interface, set up the wireless settings, enter the MAC binding, and add the MAC address of the computer you need to access the Internet.

Tools Raw Materials: routers, network cables, broadband cats, computers.

The steps to install and set up the router are as follows:

2. Then open the browser and enter the management address and login password of the router. <>

3. After logging in to the background, click the setup wizard, and then fill in the corresponding parameters according to the wizard instructions.

<>6. After the wireless setting is completed, click Save, and then restart the router to use it normally.

Setup Steps

1.Open a web browser and type in the address bar.

Open the management page of the router and enter the management account of the router (username: admin and password: admin) in the pop-up login box.

2.Select"Setup Wizard", click"Next"。

3.Choose the right way to access the Internet (there are three common ways to access the Internet: PPPOE, dynamic IP address, and static IP address, please choose your Internet access method according to the description below);

PPPoE: Dial-up Internet access, stand-alone (when the router was not used before) uses the broadband connection that comes with the Windows system to dial up, and the operator gives a username and password. This is currently the most common way to access the Internet, and ADSL lines are generally the same way to access the Internet.

Dynamic IP: Before the router, the computer can access the Internet as long as it is connected to the line, without dialing up, without setting an IP address, etc., and it will be used in community broadband, campus network and other environments.

4.Set a wireless name and password (skip this step if you're a wired broadband router).

5.Dynamic IP: Before the router, the computer can access the Internet as long as it is connected to the line, without dialing up, without setting an IP address, etc., and it will be used in community broadband, campus network and other environments. The setup is complete.

6.After the reboot is completed, enter the management interface (, open the running state, wait for 1-2 minutes, under normal circumstances, at this time, there are specific parameters after seeing the IP address of the WAN port status, which means that the router has been connected to the Internet at this time.

You need to log in to the browser to set up the stove.

Specific steps: 1. Click the setup wizard on the interface.

2. Then you will enter the next setting window, check the PPPoe Internet access mode in this setting window, and click Next.

3. After entering the next step, that is, the page of setting the password, you need to remember the username and password when setting, this is the wireless network and password, and continue to click the next step after the setting is completed.

4. Then find the SSID option on this page, and enter the password in this option, also enter a password in the PSK column, after entering, and then click Next.

5. Then click Done on the last page, so that you can set up the wireless network.

There are two ways to do this:

The first type: 1. You can look at the bottom of the router you bought. The IP address and password will be displayed on it. <>2. Then enter the IP address you see into the address bar of the browser, and then enter the password, and you can enter the settings. <>

Method 21: Right-click the network icon in the lower right corner of the notebook and select "Open Network and Sharing Center". <2. Go to the Network and Sharing Center and select Change Adapter Settings. <3. Find the wireless network, and then double-click the wireless network icon. <>

4. Open "Wi-Fi Status" and select "Details".

5. In the "Details", you can see "IPv4"and IPv4 Default Gateway. Generally, the "IPv4 Default Gateway" is the IP address of the router settings page.

6. Then enter the "IPv4 Default Gateway" address of Xingyuqiao directly into the browser, and it will pop up a router setting interface, enter and set the router administrator password.

7. Enter the password, and then you can enter the settings page of the router. <>