How to turn on the virtual router that comes with WIN7 Microsoft Vitual WIFI Miniport Adapter, pleas

Haha, I was like this at first, and it didn't help after looking on the Internet for a long time, only to find out later that I turned off the wireless network card, so the solution is to turn on the wireless network card. I opened the network card shortcut. Stable with connectify software.

apwifi too lj.

If your computer is a desktop, you must install a wireless network card to achieve it, if your computer is a desktop, you can continue to add problems, if your computer is a notebook, you can set it up like this, first ensure that the notebook wireless network card can be used normally, and then establish a new wireless access point, set the name and link password, the password is 13 letters on it, and then the mobile phone search wireless router can generally be searched, and the direct link can enter the password, or you can set it manually, Manual setting needs to fill in the name and password of the wireless network in the mobile phone network link, and the mobile phone design can refer to the manual.

It should be wireless is not turned on, I have also encountered, the switch is turned on and then entered to bear, if the wireless is turned on, you open the network sharing center to find the change adapter settings--- wireless network connection 2--- right-click to start, and then enter the netsh wlan start hostednetwork command in the run.

If it shows that the bearer network cannot be started, please check whether the new wireless network connection 2 is disabled and needs to be enabled (right-click --- enable).

It's good to turn on the wireless network card, don't listen to the first person to say a big piece, it's useless.

Need to buy a wireless router.

Microsoft Virtual WiFi Miniport Adapter is the Microsoft Virtual Wireless Micro Adapter.

By enabling Microsoft Virtual WiFi Miniport Adapter, you can turn your computer into a wireless router by enabling virtual WiFi and softAP (i.e., virtual wireless AP), enabling shared Internet access and saving network fees and router purchase fees.

When this virtual device appears in your machine, it means that you can use this virtual interface to share Internet access or form a small LAN with other devices with wireless connections.

There are two cases for this thing.

You let the computer share it yourself out of the wireless hotspot, and the phone can connect it to the Internet. You can disable this at any time yourself.

It's used for screen projection,Win10In the computer, after you turn on the miracast function of the computer,This virtual network card will automatically come out,The password is automatically set by the system,Only used for miracast projection。 In this case, the virtual NIC will disappear only after you turn off Miracast.

This is a very good function of win7,Such as the wired Internet access you use in your notebook,You can use this virtual WiFi function,Use this book as a wireless hotspot,To other devices with wifi function,Such as mobile phones、pad, etc。

How do I turn off the Wi-Fi function?

Uninstall the device in Device Manager, you refresh it again, and here's how to do it once and for all

Open the command line window as an administrator only, (Start->Attachments-> command line prompt, right-click to open with administrator privileges), and enter "netsh wlan set hostednetwork mode=disallow" to disable the virtual Wi-Fi function.

This is the driver of the computer wifi Internet access,It is recommended that you install software such as the driver wizard,Then open the software and he will scan out the missing or expired driver of your computer! You try.

However, there are a lot of wireless hotspots searched on the computer, of course, they are set up by others, so which one is opened by yourself, that is, what is the name of which one you created? How can I connect to the wireless network I created? Which god passed by and mentioned it.

Under win7, the win+r button directly brings up the run dialog box, and the two command prompts on the surface are executed separately on the OK.

SSID: the name of the wireless hotspot.

key: wireless hot occupancy password.

1. Set the wireless hotspot name and password.

netsh wlan set hostednetwork mode=allow ssid=ap key=password

2. Turn on the wireless hotspot.

netsh wlan start hostednetwork

Wireless virtual network cards can be used with the Microsoft Virtual WiFi Miniport Adapter in the following ways:

1. Click "Start" in Windows XP - All Programs - Accessories - Communication - Wireless Network Installation Wizard;

2. Log in to the "Wireless Network Installation Wizard" interface and click "Next";

3. Fill in the network name (up to 32 characters), select "Manually assign network password", and then check the option "Use WPA encryption, do not use WEP", and click "Next".

4. Fill in the network password and click "Next" to continue.

5. Select "Manual Network Setting" in the displayed window - Next", select "Finish", after the driver installation is completed, the wireless icon will appear in the notification bar in the lower right corner of the computer, click the wireless icon, and directly connect to the wireless network to access the Internet.

Useful wireless features added after the Windows 7 system update, both on supported wireless cards, virtual Wi-Fi access points! You can use a virtual network card to make the laptop a wireless WiFi hotspot for other devices that support WiFi.

You use the next drive elf, or drive the life test.

From the command line, run the following command to enable the virtual wireless NIC (equivalent to turning on the router):

netsh wlan set hostednetwork mode=allow ssid=”win7 ap wow!” key=wifimima

There are three arguments in this command:

mode: Whether to enable the virtual Wi-Fi network card, change to disallow to disable, and the virtual network card will disappear.

SSID: Specifies the name of the wireless network, preferably in English.

key: specifies the password of the wireless network. This password is used to encrypt the wireless network with secure WPA2, which can prevent the network from being rubbed off.

The above three parameters can actually be used separately, for example, only mode=disallow can directly disable the virtual wifi network card.

3.Enable Internet Connection Sharing (ICS).

In order to share the connected internet with other computers or devices, we need to enable the "Internet Connection Sharing" feature. Open the "Network Connections" window, right-click on the network connection that is connected to the Internet, select "Properties", switch to the "Shared" tab, select the checkbox in it, and select the network connection that allows it to share the Internet here i.e. our virtual wifi network card:

4.Turn on the Wi-Fi.

Continue running the following command in the command prompt:

netsh wlan start hostednetwork

to turn on the wireless network we set up earlier (equivalent to turning on the wireless function of the router. Similarly, change start to stop to turn off the wireless network).

As you can see, the virtual wireless network card has turned on the wireless network we specified, and its IP address and other attributes are assigned by the "Internet Connection Sharing" service, so it is more special.

Dude, I would like to say that there are some computers that are not supported. Unfortunately, you're one of those few. If you didn't make a mistake. It is recommended to have a soft media Rubik's Cube. You can create a WLAN with just one click.

Why? Same question... I don't understand, I don't understand, ask for an answer.