How to install a hotel fume purifier, how to install a small fume purifier in a hotel

The correct installation is: smoke hood - pipe more than 2 meters - oil fume purifier - pipe more than 2 meters - fan - direct air discharge. It is forbidden to replace the fan and fume purifier, which will cause the purification effect of the fume purifier to be halved, please install the fume purifier in accordance with the national standard installation method to achieve a better purification effect.

<>1. Install the purifier at least 2 meters away from the smoke hood outlet to ensure fire safety and purification effect; The distance between the purifier and the fan is more than 2 meters.

2. It is best to power on the machine for a period of time before installation to check whether the electrodes of the machine will be offset in transportation or handling.

3. The installation of the purifier should be at a guaranteed level, otherwise, the oil collected by the purifier will not be discharged, or the oil in the purifier cannot be drained when the oil is discharged;

4. If the radius of the center line of the elbow does not meet this condition, the wind resistance of the reducer pipe will increase exponentially).

5. The angle between the hypotenuse of the reducer pipe (small to large) and the axis is 7 degrees (if this condition is not met, the reasonable installation of the deflector should be considered.) Otherwise, the purification efficiency of the purifier will be greatly reduced and will not be able to meet the national emission standards). The beveled edge of the reducer (large to small) is angled at 15 degrees from the axis (if this condition is not met, a reasonable installation of the deflector should be considered.)

Otherwise, the purifier will not be able to fully exert its effectiveness).

6. There should be a section before the air inlet of the purifier If this condition is not met, the reasonable installation of the airflow uniform distribution plate and the deflector plate should be considered, otherwise the purifier will not be able to exert its efficiency).

7. The fan should be equipped with shock absorbers;

8. The air inlet and outlet of the fan should be installed with soft connection;

9. The purifier must be reliably grounded (the purifier has 3 outgoing wires, the red line and the green wire are connected to 220V AC, and the yellow wire is grounded).

10. Wind direction problem: the equipment is set to the left air inlet (facing the purifier electric box door, the wind direction flow from left to right is the left air inlet, and vice versa) If the right air inlet is needed on site, the electric field rotates 180 degrees, and the spring joint is moved from the lower right to the top, and then the high-voltage line is exchanged to complete the process of adjusting the left air inlet to the right air intake. There must be a filter in the direction of the air inlet.

11. In order to ensure the purification efficiency of the equipment, the equipment should work in a negative pressure state, that is, the fan must be behind the purifier.

12. When the equipment is installed outdoors, a rainproof and sun-shading awning should be installed to avoid affecting the normal service life of the equipment and increasing unnecessary maintenance costs.

13. The installation location of the purifier must be raised by the foundation in the low-lying place, and fixed with expansion bolts, and there must be enough maintenance space for the attached.

14. The purifier shall not bear heavy objects, otherwise the purifier will be deformed and cause failure, and the pipeline can be supported by a support frame.

1.When setting the exhaust air volume of the exhaust system, the exhaust air volume should be solved by matching the rated value of the fume purifier, and too small or too large exhaust air volume will endanger the clean and high efficiency of the fume purifier.

2.The oil fume purifier should be placed at a high level, otherwise, the dirty oil in the oil collection pan will be poured into the ventilation duct, or it will not be able to drain neatly when adding some oil.

3.The ventilation duct should be set to 8 10m s, too fast or too slow wind will also harm the purification rate of the fume purifier.

General installation sequence: smoke hood - fume pipeline - fume purifier - fume pipeline - fan.

Jin Jie, the equipment can be configured according to the site, and the effect of dealing with oil smoke is good, which can meet your requirements! Visually smoke-free.

1. Long-term work, low failure rate;

2. Long cleaning cycle and easy cleaning;

3. Visual inspection is smokeless;

4. No pollution in long-term operation;

5. The wind resistance of the oil fume purifier is low;

Mainly look at the area and ask the merchant which one is more suitable for you.

Many kitchens will install purifiers, which are of great help to purify oil fumes, so how to install oil fume purifiers? Let's take a look!

1. Determine the installation location.

First of all, it is necessary to determine the location and try not to choose a place with air circulation, because if the air circulation is fast, the oil smoke will be affected by the wind when it rises, and it will spread to every corner of the kitchen in advance, which will affect the purification effect of the purifier. Moreover, the smoke exhaust pipe of the purifier should be shortened as much as possible to avoid the accumulation of oil smoke in the smoke pipe, and the design design will not be bent, otherwise the smoke exhaust effect will be poor.

2. Determine the installation height.

When installing a purifier, it is also important to pay attention to the height. Because the height of the purifier will be related to its smoking effect, if it is installed too high, the smoking effect will be worse. Therefore, before installation, it is necessary to carefully confirm the height of the purifier, and also take into account the height of the user, so as not to touch the person's head when using it.

3. Determine the installation hole position.

When installing the purifier, it is necessary to punch holes in the wall to install it, and it should be noted that the purifier cannot be installed on wooden walls and cabinets, otherwise a fire will occur. Moreover, the installed wall should be stable and strong in order to meet daily use and not fall off. Then make holes in the installation position and fix them with matching screws.

After the hole is installed, the location of the socket should be planned in advance, which is usually installed about 80cm above the stove, and the socket with reliable grounding must be used.

4. Install straight pipe joints.

Next, install the straight pipe fitting of the top air outlet and install an exhaust elbow to pass through the top cabinet, so that it does not affect the appearance. Next, install the louver damper and install the wind shield facing downward.

5. Test the effect.

After the fume purifier is installed, turn on the power to check whether the product can be used normally to see how effective it is. Also pay attention to see if there will be noise in the purifier, if the noise is relatively loud, it will affect people's lives.

The fume purifier is mainly used in commercial kitchens, which can purify the fume exhaust gas into clean air, and the installation sequence of the fume purifier is as follows: stove - fume hood - ventilation duct - fume purifier - ventilation duct - fan. The ventilation ducts at both ends of the fume purifier need to be kept at a length of more than 2 meters in order to have a good purification effect.

Installation and maintenance: The reducer air duct adjacent to the air inlet and outlet of the equipment should be as smooth as possible to ensure the infectious effect of the equipment. Straight pipes that are more than 4 times longer than the diameter of the pipe must be assembled and connected with smooth pipes.

In order to ensure the infection result, the air volume of the individual fan should be greater than the intended air volume of the equipment. The equipment must work under the intended air volume, and the user can use the inverter to control the fan or install a regulating valve device at the air outlet of the fan.