Do you have to do dynamic balancing after replacing the wheels?

Hello, there is no need to replace the wheel hub, and there is no way to do it in the general repair shop, if it is to replace the tire, then it is needed, and it can be done on the tire dynamic balancing machine, the wheel hub is generally done during production, thank you.

Balancing must be done after changing the tires. The reasons why dynamic balance must be done after replacing tires: (1) The wheels of the car are composed of tires and hubs as a whole.

However, due to manufacturing reasons, it is impossible for the mass distribution of the parts of this whole to be very uniform. (2) When the wheels of the car rotate at high speed, a dynamic unbalance state will be formed, resulting in the phenomenon that the wheels of the vehicle shake and the steering wheel vibrates during driving. In order to avoid this phenomenon or to eliminate the phenomenon that has already occurred, it is necessary to make the wheel correct the balance of each edge part by increasing the counterweight in the dynamic situation.

This process of correction is often referred to as dynamic equilibrium. (3) Tire balance is divided into two types: dynamic balance and static balance. Dynamic imbalance causes the wheels to sway, causing the tires to wear in waves. Static imbalance can cause bumps and runouts, often causing flat spots in the tires.

Therefore, regular balance testing can not only prolong the life of tires, but also improve the stability of the car when driving, and avoid traffic accidents caused by tire swinging, jumping, and loss of control at high speeds.

This must be dynamically balanced, and not running will cause fighting.

It is recommended to do it for safety.

When it comes to automatic balancing machines, Xiaogan City Jingheng Balance occupies an indispensable place. The whole country and even the world, there are R & D, design, manufacturing automatic dynamic balancing machine enterprises, the strength is bound to be not bad, Xiaogan precision balancing machine in the quality control at the same time, but also close to the people.

Hello, this one needs to be done.

In most cases, the need to replace the hub is dynamic balancing, not wheel alignment. Dynamic balance preparation refers to the increase of counterweight in a lighter place through instrument inspection, so that the center of gravity of the tire is always kept in the center, so as to avoid the uneven stress state of the tire in the process of high-speed rotation. The purpose of the wheel alignment is to keep the wheels straight while the vehicle is moving, while ensuring that it is steering.

In most cases, the need to replace the hub is dynamic balancing, not wheel alignment. Dynamic balancing refers to increasing the counterweight in a lighter place through instrument inspection, so that the center of gravity of the tire is always kept in the center, so as to avoid the uneven stress state of the tire in the process of high-speed rotation. The purpose of the four-wheel alignment is to keep the wheels in a straight line while the vehicle is moving, while ensuring that the steering wheel can automatically return to the center after steering.

Four-wheel alignment is a repair project, and most of the accidents on the car have damage to the chassis and suspension. When chassis parts fail and need to be replaced and repaired; Tires are eccentric, and the wear on both sides is uneven; Four-wheel alignment is required in four situations, i.e., when the vehicle feels off while driving.

Most of them need to adjust the dynamic balance after the tire and wheel hub are reassembled, such as replacing the wheel, tire, repairing the tire, installing the tire pressure monitoring module, replacing the valve of different materials, etc. If the wheels are unbalanced when rolling, the wheels can be clearly felt beating while driving, and even when the vehicle reaches a certain speed, it will cause resonance, and the realistic reaction is that the steering wheel shakes and vibrates.

Cars are mainly divided into four-wheel alignment and dynamic balancing. Wheel alignment is not a usual maintenance item, but a maintenance item. You need to know when to perform a wheel alignment or balancing check to reduce the risk factor when driving.

New tires for the front or rear wheels.

It is better to replace the front drive with the front wheels and the rear drive with the rear wheels. The reason for this operation is that the common denominator of these two types of tire placement is that they are basically placed on the drive wheels. With new tires, they can have better grip and drainage, and better safety when driving.

Accessories: Tire Replacement Specifications:

1.Look at the wear marks of the tires:

Most tires basically have signs of wear, which can be used as a reference value for tire wear. When the surface pattern of the tire is worn below the millimeter, it should be replaced. If it is not replaced immediately, when driving, because the tire wear is quite serious, it is easy to slip, which increases the safety hazard, which is a taboo when driving, so it is necessary to replace the new tire immediately.

2.Look at the damage to the tires:

In the usual driving process, it is inevitable that there will be a phenomenon of puncture, if the number of tire repairs is quite a lot, advocate immediate replacement of new tires, the tires that have been repaired will be greatly reduced in the service cycle, at the same time, when testing tires at ordinary times, if there are visible cracks and cuts on the sidewall of tires, this type of tires must also be noted, these tires are often the root cause of punctures when driving, and a little bulging tires are also to be replaced immediately to prevent potential safety hazards when driving. Do you want to do dynamic balancing of new wheels New tires put front wheels or rear wheels @2019

Summary. Dear, glad to answer for you. The front and rear hubs and tires of the trolley are interchangeably used for dynamic balancing.

Here's why:1This is because the weight distribution of each hub and tire is different, and dynamic balancing is required at the time of installation to ensure that the entire wheel set does not have excessive vibration at high speeds.

2.Unbalanced wheels and tires can lead to increased wear and tear on the vehicle's suspension and steering components. <>

<> the front and rear hubs and tires of the trolley are interchangeable, and there is no need to do dynamic balancing.

Dear, glad to answer for you. The front and rear hubs and tires of the trolley are interchangeably used for dynamic balancing. The reasons for divination are as follows:

1.This is because the weight distribution of each hub and tire is different, and dynamic balancing is required at the time of installation to ensure that the entire wheel set does not have excessive vibration at high speeds. 2.

Unbalanced wheels and tires can lead to increased wear and tear on the vehicle's suspension and steering components. [Smile ruler cheat lead] <>

Xianling good flowers] <>

Dear, the expansion for you is the front and rear wheels and tires of the car nuclear grinding precautions: 1Unbalanced wheels and tires will cause the vehicle to lose stability while driving, affecting driving safety.

2.In order to ensure a comfortable and safe ride, it is necessary to adjust the dynamic balance after replacing the wheels and tires. <>

Because the vehicle is moving at high speed, it is difficult to achieve the speed requirements without a balancing machine.

To put it simply, if you don't do dynamic balancing, you are prone to steering wheel shaking when you run at high speed, and even tire swinging and jumping, which may even lead to loss of control and then cause a traffic accident.

Moreover, not doing dynamic balancing will also cause the tire to wear eccentricly, which will not only affect the life of the tire, but also affect the driving safety.

Counterweight imbalance over time can also wear out your suspension and bearings excessively, causing damage to the vehicle itself.

Finally, I would like to tell you that most auto repair shops, tire shops, and all 4S shops can provide dynamic balance services. Although dynamic balancing can be done in many places, but the difference is huge, cheap 2 30 yuan per wheel, rough and expensive can reach 70 80 yuan per wheel, but this is not the more expensive the better, it is recommended that you go to a regular or familiar 4S shop or auto repair shop to do.