Ask what to pay attention to when you unplug the keycaps to clean up the keyboard, and the high boun

··· Pure hand-hitting·· I hope to be patient and read it through...

What kind of keyboard do you have? Generally, most of the keyboards above 100 yuan are 3-star waterproof, and the 5-star waterproof of Shuangfeiyan is more nb can be played directly in the water It's a bit far-fetched =. =

All you need to do is to buckle all the buttons, it is recommended that you use a professional button to buckle the keyboard, if not, you first buckle the CTRL in the lower left corner, and then use a small screwdriver or a knife or something like that to knock down the other buttons, and soak them in the water. As for what you said it will be difficult to install it again, this is impossible, unless you unscrew the screws of the keyboard and clean up the inside, it is recommended that you do not do this, because the inside will basically not enter the dust, and the inside is a circuit board, which is easy to misplace. Just clean the keys and you're fine, 1:

The keycaps won't damage the keyboard unless you mess around.

4: This is what needs to be noted, no need to open the inside, I said above, the inside is a circuit board, a misalignment may be the keyboard will be scrapped (a bit exaggerated).

One last tip: the shift key and the enter key of the keyboard generally have something like an iron hook, don't throw the iron hook when you reload the key! Be sure to put it back! Otherwise enter and shift are hard to press.

If there's a problem, then hi me, it's okay to clean it up like this, my keyboard is razer's black-bellied tarantula, and if you do it like this, it won't break.

··· Pure hand-hitting·· I hope to be patient and read it through...

What model of mobile phone are you, it's hard to say whether it's a different phone.

If you have to disassemble the phone yourself, it is recommended that you search for the official disassembly of this mobile phone**,There are all on the Internet, I will use 5700 to learn the official disassembly** After dismantling the shell and changing the keyboard myself。

There shouldn't be any problems, just a simple cleanup.

However, it is still recommended that you go to the mobile phone repair department for 5 yuan!

Hope it helps.

Preparation tools: wire key puller, plastic key puller, metal key puller.

Taking the plugged keyboard operation as an example, the specific operation steps are as follows:

1. First of all, use the wire key puller to press it into the gap of the key cap, at this time, just twist it and pull it out upwards as shown in the figure below.

2. Next, the operation method of the plastic key puller and the wire key puller is the same, insert and screw out, as shown in the figure below.

3. Finally, at this time, you can insert the metal key extractor and pull it out directly, as shown in the figure below.

Here's how to do it:

Preparation tools: wire key puller, plastic key puller, metal key puller.

1. Use the wire key puller to press it into the gap of the keycap, just twist and pull up, as shown in the figure below.

2. The plastic key puller has the same operation as the wire key puller, insert and screw out, as shown in the figure below.

3. Insert the metal key puller, and then pull it out directly, as shown in the figure below.

There is a special screwdriver for this, so if you don't have one, use a small screwdriver or knife to pry it off.

Dig out the ears with a change! That's what I did!

Find a pen, scissors or something like that will come down with a warp.

I usually rinse with clean water and then blow with a hot blow dryer repeatedly. Just be careful not to get water inside the keyboard. It's okay to get some water. It is best to open the screws and dry them with a hot blow-dryer.

Tips for life to quickly clean up the junk on your keyboard.

It's okay to brush it, don't use too much force, it's fine, and it's clean.

1. The first is the wire type, press the wire into the gap of the keycap, twist it and pull it up, I highly recommend this kind of key puller, the advantage is that it will not cause any damage to the keycap.

2. The second is the plastic type, the method is the same as that of the wire, but the problem is that the buckle is too small and short, and the operation is inconvenient.

3. The third type, metal key puller, this is basically a gift of brand keyboards, but the shortcomings are too obvious, it is very easy to scratch the keycaps, there are other specifications, but the principle is the same.