Can I use a tp LINK cat with router to access the Internet on two computers together?

Yes! It's better to specify the IP! If the gateway is not set up, it will definitely not be able to connect to the network!

Other reasons for the impact: 1. Some network operators do not allow multi-machine sharing of Internet access! 2. The routing settings are incorrect!

Cut. The first thing to do is to look at those who can only copy and paste. In fact, the landlord, your settings should be not wrong. It's just a little less. I don't think DHCP in your routing cat is enabled. As long as it's enabled, there's no problem.

A network (a cat) has only one "identity", and can only correspond to one router (main router), but after this router can go out, it can be connected to multiple routers (equivalent to a local area network).

Specific methods: 1. Connect a (main) router after the cat, and set the router to surf the Internet normally.

Second, there are several WLAN ports on the main router, each port can correspond to a sub-router, and each router is equivalent to a local area network.

The broadband modem has a single port output and a four-port output shown in Figure 2.

Figure 1 Single-port output broadband cat.

Figure 2 Four-port output broadband cat.

1. Output broadband cats to a single port.

1. Single-port output: The optical modem output has one interface and only one network port;

2. A computer or a broadband router can be connected to the output network port;

3. Conclusion: A broadband modem with a single output interface cannot be plugged into a computer and a router at a time.

Second, for the output of four ports, one is plugged into the computer and one is plugged into the router cat.

1. The output of four ports is plugged into a computer and a router is plugged in, and there are four interfaces, including three network ports and one IPTV interface;

2. In these three network ports (network port 1, network port 3 and network port 4), three computers or broadband routers can be connected respectively;

3. Conclusion: The four-port output is plugged into the computer and the router is plugged in, and one can be plugged into the computer and one router at the same time.

1. If the cat comes with multiple RJ45 network ports, it is theoretically possible, and most of this is ADSL cats.

2、Most of the current fiber optic cats only have 2 interfaces,The first one is connected to a computer or router,The other is connected to a network TV,This can't be mixed。

Generally, it can't be at the same time, just connect the computer under the router.

The easiest way is to buy you a wireless router and ask them to install it for you. I just told them to come back and get it for me

Mine is the same as the landlord.。。

Yes, I also have two routers in my house. Here's how I set it up :

First of all, a main router, (Note: When choosing a main router, choose a functional one, mine is one that can limit the speed and has wireless functions.) Connect to that router on ADSL.

Then drag a network cable from any output port of the main router and insert it into the output port of the other secondary router. (Note that it's the output.) Both are outputs.

The input port of the secondary router is not used. ）

It is best to restore the secondary router to factory settings, and then be sure to note that the IP addresses of the two routers cannot be the same. I used to have both of them and then the computer jumped to the secondary router by default, which caused me to not be able to access the Internet. This can be changed in the network parameters section of the router settings page.

Then you'll be able to surf the internet. The computer is connected to four, it is recommended that your main router has a speed limiting function, otherwise you will be miserable.

Yes, 1, set the IP of the WAN port of the second route to the same network segment as the LAN port of the first route, 2, set the IP of the LAN port of the second route to a new network segment, 3, set the IP of the PC connected to the second route to be in the same network segment as the LNA port of the second route---.

Most of the home routers are set and switched ports.

It's relatively simple, you only need to buy one more switch, it's a switch, not a router, so it's very convenient, and you don't have to set anything up! The premise is that there is a wire pulling through the switch from the route, and the role of the switch is to share the signal! Then the other two computers are plugged into the switch!

Don't have to worry about two routes! Buy a switch with five mouths and eight ports to meet your needs!

Ordinary routers at home can't routers are assigned addresses to other computers If two routers are on it, there will be conflicts Occasionally you can surf the Internet, but the field is disconnected, and a router is connected to a switch.

It is recommended that you switch to a different switch! You can also change to a router with many interfaces!

How much network signal loss will be within 100 meters from the main router to the sub-router?