What to do if your Rolex watch goes fast? What to do if your Rolex watch goes fast

Five common reasons for watch time error and watch time inaccuracy:

1) Insufficient power reserve: You need to check whether the power is sufficient, if the amount of movement of the self-winding mechanical watch is very small, it may also cause insufficient power reserve, you can replenish the power by manual winding, and then observe whether it continues to have the phenomenon of fast and slow.

2) Insufficient power: If the quartz watch suddenly finds that it is slow, it is likely to be caused by insufficient battery energy, and you can send the watch to a special maintenance point to check the power.

3) Hit or hit: The watch is very tight, if it is hit or hit, it may cause loose damage to the internal parts, and it may also cause the problem of running time. This is to be dealt with in a timely manner.

4) Need to maintain: The lack of oil in the movement or the wear and aging of internal parts may cause time problems, which need to be maintained, and need to be sent to the designated maintenance point for maintenance services.

5) In addition to the above common situations, the watch is affected by some ambient temperatures: if the hairspring of the watch is magnetized, the watch will not be accurate.

Our mechanical watches often have the situation that the time is not accurate, and most people wonder if the mechanical watch is broken. There are many reasons why a mechanical watch can be parked, but there are several main reasons.

1. Insufficient kinetic energy: The watch is not winded enough, and the kinetic energy is insufficient. In particular, automatic watches require more arm movement, and the winding efficiency is very low. If you usually exercise a little bit, you can wind it manually, which can ensure enough kinetic energy.

2. Gear failure: Gear train failure such as deviation wheel and center wheel failure will lead to the condition of stealing stop of the watch. These situations are often not easy to detect and require disassembly, careful inspection and testing to find out the problem and solve the problem.

3. Lack of maintenance: mechanical watches should be maintained every 2-3 years or so. If it is not maintained for a long time, a large amount of oil sludge will be generated inside. Friction between gears increases, causing slippage.

The reasons that cause the watch to go faster: 1. The hairspring is magnetized; 2. The swing of the mechanical watch; 3. You can open the warranty coupon attached to the purchase of the watch when rubbing against the fast and slow clip or the outer pile, and under normal circumstances, there will be a service address on the warranty link, or find a regular watch service center for testing and maintenance of the address of the store, etc., if there is a professional after-sales maintenance center nearby, it is also possible.

Small pieces of calcium chloride can be directly wrapped with gauze; Then take out the watch cover and put the calcium chloride wrapped in gauze and the electronic watch seal into a plastic bag and box. After waiting for half a day, you can take out the watch, and you can see the moisture of the electronic watch disappear. If the water ingress of the watch is serious, it can be left for a day.

Wear the watch backwards. You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours. If the water ingress is severe.

Send it to the watch shop to wipe the oil. None of the above two methods can remove the moisture, so you should immediately send it to the watch shop to wipe the oil and remove the moisture from the movement to avoid rust on the parts.

The watch maintenance center is located in Room 808, Block E1, Office Building, Oriental Plaza (East 1), No. 1 East Chang'an Street, Dongcheng District, Beijing.

Reasons why the watch is not running accurately:

1. Insufficient power reserve. If the amount of exercise is small, it may also cause a lack of power reserve, so you can replenish the power by winding it manually, and then observe whether it continues to be fast or slow.

2. The watch has been hit or impacted, which may cause loose damage to the internal parts and may also cause the problem of running time.

3. The lack of oil in the movement or the wear and aging of the internal parts may cause the problem of running time, which needs to be maintained.

4. The watch is magnetized: If the hairspring of the watch is magnetized, the watch will not be accurate. The influence of the wearer's usage habits may cause an increase in the time error. Sending the watch to a repair center for inspection and adjustment will restore the watch to its normal tolerance.

The watch maintenance center is located in Room 1003, 10th Floor, Hongyi International Plaza, No. 299 Nanjing East Road, Huangpu District, Shanghai

The mechanical watch goes fast first because the position error of the watch is relatively large, for example, the precision of the hand surface and the face is different, the error of the façade luck is relatively large, when worn, its comprehensive uniform daily error is relatively increased, the position error is a key indicator of the performance of the watch, and the general change index should be as small as possible.

There is also a common problem with the fast movement of mechanical watches, that is, the secondary outer ring of the hairspring rubs against the outer pile of the hairspring, which is also displayed on the façade and dynamics, especially if the watch has been touched before, and the hairspring is most likely to be in trouble after deformation; This sub-position, it depends on what the movement is, if it is the general ETA class men's watch movement, it is easier to display the left or upper position of the watch on the wrist, this situation requires the adjustment of the space between the secondary outer ring of the hairspring and the outer pile of the hairspring, and there should be a reasonable and safe distance between them.

Rolex after-sales service center: the reason why the watch is slow:

1.Insufficient power: mechanical watches are divided into manual mechanical watches and automatic mechanical watches, insufficient power is an important reason for the watch to slow down or stop the watch, manual mechanical watches can be wound directly when they are slow, and the reason why automatic mechanical watches are slow is mostly because of insufficient wearing time or the arm does not maintain a normal amount of exercise, and it can be directly manually wound to supplement the power.

2.No maintenance: mechanical watches are generally maintained once every 2 to 3 years, the lubricating oil in the movement will dry up, and the friction of each gear will produce iron filings after a long time, increasing the friction between the gears.

3.Shock: A mechanical watch has a complex structure and is composed of hundreds of precision parts, which is very fragile, and the watch is subjected to a strong impact, and the parts in the movement may loosen and cause the watch to slow down or stop.

There are four reasons why mechanical watches are moving faster:

1. The lubricating oil of the mechanical watch penetrates into the hairspring, or leaks, or overflows, so that the extremely precise hairspring is "sticked" together, shortening the length of the hairspring, which leads to the speed of the balance wheel of the watch to accelerate, resulting in time "running fast", this situation needs to be sent to the repair shop to the professional master to deal with, so that the hairspring can return to normal.

2. It is still a hairspring, and the hairspring is hung on the outer pile of the hairspring. Due to vibration and other reasons, the hairspring was instantly "deformed", "rubbed" on the outer pile of the hairspring and hung on it. This is the same reason as the "sticky" oil of the hairspring, which leads to the "running fast" of time.

This kind of harm is greater, and it needs to be repaired in time, and the hairspring can be "picked" away from the outer pile of the hairspring.

3. The hairspring is magnetized, and the time "runs fast" due to the contact magnetic field, and the watch can be put into the demagnetizer to demagnetize.

4. The fork pad of the escape wheel is faulty, and the kinetic energy release speed of the escape wheel cannot be effectively controlled. As a result, time "runs fast". I had to swap it out. It also needs to be sent to a professional watch store for repair.

If the watch you just bought is fast, then it is likely to be magnetized. Because after the hairspring is magnetized, the circle between the rings is only shown when wearing, there is a sticky or short loop, especially in the façade, the hairspring will hang down due to its own gravity, and the shaking of the arm will aggravate its radial movement, resulting in fast walking.

Here should be sent to a professional repair shop with a professional demagnetizer to demagnetize it, do not be greedy to go to the roadside stall for maintenance, so as not to repair the more bad, in addition to the watch demagnetization does not need to disassemble the watch, the cost is generally not high.

If the test result is still fast after demagnetization, it may be that the pendulum frequency of the mechanical watch has become larger, and the general watch relies on the hairspring to retract and control the swing, which is the basic principle of adjusting the speed and slowness. Make the hairspring available for retraction shorter, the swing will be smaller, the frequency of the swing will be larger, and the watch will be faster. If you need to open the lid for comparison, it is recommended to send it to the store for processing, and some complex watches also need to be sent back to the production factory by the store for processing.

If a Rolex watch is magnetized, the hands will run very quickly, so it should be taken to a regular store for demagnetization and kept away from household appliances during normal wear. If it is caused by strong vibration, the watch should be taken to the store for inspection and treatment to avoid wear and tear of the internal parts.

1. Degaussing treatment.

Rolex watch is a more expensive brand-name watch, when the hands appear faster and faster, it may be caused by the magnetism of the watch, and the time will be inaccurate, you can take the watch in a regular store for demagnetization, and stay away from daily electrical appliances at ordinary times, so as not to affect the service life of the watch.

2. Avoid vibration.

If in the process of wearing, the Rolex watch is often subjected to strong vibration, which will cause the hairspring inside to stick, resulting in the phenomenon of fast walking, at this time, the watch should be sent to a professional store for inspection and processing, and attention should be paid to avoid vigorous ** or bumps in ordinary times.

3. Regular maintenance.

If the gears in the Rolex watch are faulty, or if there is a foreign object stuck inside, it will also lead to incorrect timekeeping, so it is necessary to send the watch to a regular store for careful inspection, and then prescribe the right medicine according to different situations, and at the same time maintain it regularly to prolong the service life of the watch.

Summary. 1. Insufficient power reserve. You need to check whether the power is sufficient, if the amount of movement of the self-winding mechanical watch is very small, it may also cause insufficient power reserve, you can supplement the power by manual winding, and then observe whether there is a phenomenon of speed and slowness, if it is still recommended to go to the special repair shop for testing.

1. Insufficient power reserve. You need to check whether the power is sufficient, if the amount of movement of the self-winding mechanical watch is very small, it may also cause insufficient power reserve, you can supplement the power by manual winding, and then observe whether there is a phenomenon of speed and slowness, if it is still recommended to go to the special repair shop for testing.

Having been hit or impacted. The watch is very tight, if it is hit or hit, it may cause loose damage to the internal parts, and it may also cause time problems, so it is recommended to go to a special repair shop for testing.