How can a Rolex watch stop beating when it is stationary

Our mechanical watches often have the situation that the time is not accurate, and most people wonder if the mechanical watch is broken. There are many reasons why a mechanical watch can be parked, but there are several main reasons.

1. Insufficient kinetic energy: The watch is not winded enough, and the kinetic energy is insufficient. In particular, automatic watches require more arm movement, and the winding efficiency is very low. If you usually exercise a little bit, you can wind it manually, which can ensure enough kinetic energy.

2. Gear failure: Gear train failure such as deviation wheel and center wheel failure will lead to the condition of stealing stop of the watch. These situations are often not easy to detect and require disassembly, careful inspection and testing to find out the problem and solve the problem.

3. Lack of maintenance: mechanical watches should be maintained every 2-3 years or so. If it is not maintained for a long time, a large amount of oil sludge will be generated inside. Friction between gears increases, causing slippage.

There will be after-sales ** on your warranty link, call after-sales ** to inquire about the after-sales address.

In the case of a movement watch, it is possible that there is not enough time to carry it, or that the crown has not been turned enough times.

Sino-Swiss International Watch Customer Center.

Reason for stopping:

The more common reason may be the lack of kinetic energy, automatic mechanical watches do not need to be manually wound, but to keep the mechanical watch on the hand to wear at least 8 hours of time, because the automatic mechanical watch uses the arbitrary swing of the rotor to wind up, and the rotor swings with the movement of the arm, so if the mechanical watch needs to be worn on the hand often.

But if you often wear it on your hand and don't walk, it may also be a lack of kinetic energy, and then we need to manually wind it.

After the above methods, the machine is not gone, here we can rule out the reason for the lack of kinetic energy of the mechanical watch, it should be the failure of the mechanical watch, if you are not a watch professional, it is best not to disassemble it rashly, please send it to a professional watch repairer for repair.

The following is an introduction to the five common reasons for the inaccuracy of the watch time

1: Insufficient power reserve: You need to check whether the power is sufficient, if the amount of exercise is small, the power reserve may be insufficient, you can supplement the power by manual winding, and then observe whether it continues to have the phenomenon of fast and slow.

2: Insufficient power: If the quartz watch suddenly finds that it is slowing, it is likely to be caused by insufficient battery energy, and you can send the watch to a special maintenance point to check the power.

3: The watch has been hit or impacted: the watch is very tight, if it is hit or hit, it may cause loose damage to the internal parts, and it may also cause the problem of running time. This is to be dealt with in a timely manner.

4: Need maintenance: The lack of oil in the movement or the wear and aging of the internal parts may cause the problem of running time, which needs to be maintained, and needs to be sent to the designated maintenance point for maintenance services.

5: In addition to the above common situations, some ambient temperatures affect the watch by magnetism: if the balance spring of the watch is magnetized, the watch will not be accurate.

1. Visual error. 2. The balance wheel in the movement stops when it is shaken. Third, there are problems elsewhere...

Visual error, or there is a problem with the watch, go to the labor clothes to see, if the shaking stops, take it down for a day, I don't know how much slower it will be.

A fully automatic mechanical watch that operates by the action of an automatic winding mechanism that winds the mainspring when the rotor is turned in any direction (visible on the transparent bottom cover). It is conceivable that only by wearing the watch on the hand, the rotor will also rotate to generate energy as the arm moves. Generally, a fully automatic watch should be worn on the hand for more than 8 hours a day to replenish the energy of the clockwork, but it is not absolute.

Only when you wear it on your hand and constantly replenish the energy of the clockwork, will the watch not stop. Nowadays, there are people who work in the office, and the watch often stops and goes, in addition to the movement, because the wearer itself has insufficient exercise to replenish enough energy to the mainspring.

In fact, there are many reasons why mechanical watches do not go, such as: bumps, movement gear misalignment, magnetization of the watch, shelving for a long time, sludge drying, etc., generally divided into two kinds, the first is because of insufficient kinetic energy. The second is due to a malfunction of the mechanical watch.

Therefore, don't panic too much when you find that the mechanical watch is not leaving, and first distinguish which kind of big one it belongs to.

1. Insufficient power reserve. You need to check whether the power is sufficient, if the amount of movement of the self-winding mechanical watch is small, it may also cause insufficient power reserve, you can supplement the power by manual winding, and then observe whether there is a phenomenon of speed and slowness, if it is still recommended to go to the store for testing.

2. The power is insufficient. If the quartz watch suddenly finds that it is slowing, it is likely to be caused by insufficient battery energy.

3. Having been beaten or impacted. The watch is very tight, if it is hit or dropped, it may cause loose damage to the internal parts, and it may also cause time problems, so it is recommended to go to the store for testing.

4. Maintenance is required. A lack of oil or wear and tear of the internal parts of the movement can cause time-keeping problems and require maintenance.

5. Under the influence of ambient temperature, the watch is magnetized: if the hairspring of the watch is magnetized, the watch will not be accurate. The influence of the wearer's usage habits may cause an increase in the error of the time, which will be sent to the store.

Note: 1. Mechanical watches vary according to the model and manufacturing quality of the movement, and the error of the general watch within 30 seconds per day is within the normal range. Some of the higher precision movements can reach around 10 seconds.

Hello, it is our pleasure to assist you in answering the following question: when a Rolex watch stops, it may be due to a dead battery or a malfunction in the movement. First of all, you should check if the battery is depleted, and if so, you need to replace it with a new one.

If not, the movement may be faulty and the watch needs to be taken to a professional repair shop for overhaul. The repair shop will check the movement, replace the parts, clean the movement, change the oil film, etc., according to the condition of the watch, to ensure that the watch can operate normally.

Summary. In general, there are many reasons why a Rolex watch stops, and the main reasons are:1

It may be that the watch is not powered enough, the second hand of the watch is loose, or even it may be caused by damage to the internal movement of the watch and the parts will fall off2It is also possible that the watch has been left for a long time and the oil sludge has dried up, so don't panic too much when you find that the mechanical watch does not go or even the whole does not go, you must first figure out what is the reason why the second hand of the watch does not go, and then analyze the specific reasons.

In general, there are many reasons why a Rolex watch stops, and the main reasons are:1It may be that the watch is not powered enough, the second hand of the watch is loose, or even it may be caused by damage to the internal movement of the watch and the parts will fall off2

It is also possible that the watch has been left for a long time and the oil sludge has dried up, so don't panic too much when you find that the mechanical watch does not go or even the whole does not go, you must first figure out what is the reason why the second hand of the watch does not go, and then analyze the specific reasons.

Solutions for Rolex watches to stoppage (1) If you don't deal with it in time just because of the lack of power in your Rolex mechanical watch, it is easy to cause a delay in time, thus delaying your time. It only needs to be wound regularly to ensure that the watch has sufficient kinetic energy, and there is no need for other maintenance. (2) If it is determined that the second hand of the watch is loose, you only need to tighten the second hand after the sale, and the maintenance method in this case is relatively simple.

You can ask the professional master who repairs the watch to detect the fault of the watch with the instrument of the watch, and then make targeted repairs. I wish you a happy life and all the best

Hello, it is a pleasure to serve you and give you the following answers: Reasons:1

A Rolex watch may stop functioning because it has not been charged in time; 2.A Rolex watch may stop working due to damage; 3.A Rolex watch may stop functioning because it is not properly installed; 4.

A Rolex watch may stop functioning because it has not been properly adjusted; Workaround:1If your Rolex watch doesn't charge in time, you can try charging it to see if it can get back to normal operation; 2.

If your Rolex watch is damaged, you can try to check the battery, movement and other parts of the watch to see if there are any damaged parts, and if so, you can try to replace them; 3.If your Rolex watch doesn't install correctly, you can try reinstalling it to see if it can get back to normal operation; 4.If your Rolex watch doesn't adjust correctly, you can try readjusting it to see if it can get back to normal operation.

Steps:1Charging:

Plug your Rolex watch into a power source and charge it; 2.Inspection: Check the battery, movement and other parts of the watch to see if there are any damaged parts; 3.

Installation: Reinstall the Rolex watch; 4.Adjustments:

Readjust your Rolex watch. Personal experience: A Rolex watch is a high-end watch, its quality and performance are excellent, but it can also stop working, so when we use a Rolex watch, we should charge it in time, check it regularly, install and adjust it correctly to ensure that the Rolex watch can operate normally.