What to do if the back cover of the watch is loose, the back cover of the watch is open. How do you

Adjust the position of the lid, such as which direction the notch is facing, so as not to buckle the wrong position.

Turn the lid down with the front of the watch facing up.

Balance the ZD gaps on each side of the lid and keep them basically the same in all directions.

Place the table back cover on a rigid tabletop.

Put a soft cloth on the inner glass of the watch, and press down with the palm of your hand to press it evenly, and be careful to hurt your hands in the process.

If you don't know how to do it, it is recommended to go to a professional watch repair technician to deal with it, so that it will not hurt your hands, and the watch can be as perfect as ever.

If it is a square bottom, you can press it with a little force.

If it is the bottom of the gong wire, find a small gong wire batch and tighten the gong wire.

If it's a round bottom, a sucker or a tooth bottom, take it to a watch repair shop.

Close the back cover, please pay attention to whether the rubber ring inside has fallen off, otherwise it will affect the waterproof performance.

Point some 502 glue around the periphery, and open it with a knife when repairing.

This problem is easy to solve·· You find a hammer... Just smash it in the back of the photo·· Be sure to put something on before smashing, or it won't be strong.

Tighten the point, you can also consider buying a new one.

1 First, prepare the mechanical watch and back cover to be operated.

2 Second, pick up the back cover of the mechanical watch with one hand.

3 Then, place the back cover of the mechanical watch on the spot where the back cover of the watch is placed.

4 Next, slowly adjust the position of the back cover by hand.

5 Then, pinch the back cover and screen of the mechanical watch with both hands and squeeze them firmly.

6 Finally, after completing the above steps, you can see that the back cover of the watch is covered.

The reason why the back cover of the watch cannot be attached is because the back cover of the watch is a product with a more accurate shell processing. It's not easy to pry it open by hand and then press it back.

The specific solution can be to close the back cover of the watch with a rolling pin, see if there is a rolling pin at home, and then find an old book, or put a piece of paper about 1cm under the book to prevent the watch mirror from being scratched. Then press the back cover left and right with a rolling pin, repeatedly exert force, pay attention to the use of skilled strength, try a few more times, and you're good to go.

Extended Information: Precautions for Watch Maintenance:

1.Do not use the watch (including waterproof watches) in hot baths, saunas, or environments with large temperature changes.

2.Do not operate the pushers and adjust the crown in water.

3.Please clean the strap and case regularly; If it is a leather strap, avoid contact with moisture, moisture, makeup, and sun exposure.

4.Pay attention to the anti-magnetic nature of your watch and avoid prolonged contact with electrical appliances, mobile phones, and magnets.

5.Do not disassemble the watch under any circumstances.

This kind of back cover is pressed up by a special machine, and the average person has so much strength in wood.

If you are not afraid of breaking it, you can find a cap with a diameter slightly larger than the dial glass, fasten it to the dial glass, wrap it in a fixed position with tape, and then stuff the watch into a drawer, then stuff it into a wooden rod, and press the back cover into it with a lever principle.

It's best to go to the watch repair shop to get it, just press the back cover, it won't cost much.

Here's how:

1. The screw lock back cover is a relatively easy to handle, there are small screws on the back cover of the watch, we only need to align the screw mouth, and then lock it tightly. Whether it is disassembly or installation, it is relatively simple, but it also requires enough patience and care.

2. Screw back cover, you need to align the cover with each screw mouth behind the watch, and then try to press down, which can help us close the cover of the back cover of the watch.

3. The pull-type back cover requires more pressure when installing, so it is recommended to put a soft cloth under the watch and break the glass when pressing hard. Of course, even if it is a tie-type back cover, you can't use brute force, only by aiming at the direction of the latch, you can close the back cover of the watch more quickly.

Precautions

When closing the back cover of the watch, pay attention to the rubber seal. There is a rubber sealing ring inside the back cover of the watch, which is to prevent the watch from entering the water, when the back cover is opened, we need to pay attention not to damage the rubber sealing ring, check the rubber ring while closing the back cover, and replace it in time once it is aged, so as to ensure the integrity of the waterproof performance of the watch.

Here it is recommended not to open the back cover of the watch without permission unless necessary, there is no professional tool to open the cover, and there is no skilled technique, so it is best to go to a professional watch repair shop.

Many people like to open the back cover to check it after encountering problems with the watch, but the biggest disadvantage of this is that many people can't install it back after disassembling it, which is very embarrassing, and it is easy to lose small parts.

How to cover the back cover of the watch.

Press it hard, if it doesn't work, go to the repair shop and press it with a capper.

There is a small mouth facing the direction of the watch handle, turn over the watch handle to the left and look at the word is positive, the direction is right, protect the watch glass, and press hard. If you are afraid of damaging the watch glass, you should go to a master who repairs the watch and clip it with a tool, and you generally don't charge money.

Steps to install the back cover of the watch.

It is easy to have problems when installing the watch, and it is often encountered that the back cover of the watch cannot be buckled, and all attempts have ended in failure. Here's how to install it correctly!

Place the table back cover on a rigid tabletop. Place a soft cloth on the front glass of the watch and press down with the palm of your hand to apply even pressure. Adjust the position of the lid, such as which direction the notch is facing, so as not to buckle the wrong position.

Turn the lid down with the front of the watch facing up. Balance the gaps on each side of the lid (keeping all directions basically the same). In this way, the back cover of the watch was successfully replaced.

How to maintain the watch.

1.Please use the watch at room temperature, if the temperature exceeds the tolerance range, the watch will be damaged or even stop working.

2.Do not wear the watch in a hot environment to avoid burns**.

3.Never leave the watch in a place where it is exposed to high temperatures to avoid damage to the watch.

4.Do not place the watch next to a magnet, if you place the watch next to a magnetic health device such as a magnetic necklace, or a magnetic suction lock on the refrigerator door, a handbag buckle or a mobile ** earphone, it will cause the watch to run inaccurately. If this happens, remove the watch and reset the time.

5.Do not place your watch next to household appliances that generate static electricity, as the watch may not be able to keep out of time if it comes into contact with strong static electricity emitted by the TV screen.

6.Do not subject the watch to strong vibrations, such as when the watch falls to the ground.

What to do if the watch doesn't go.

If the watch is gone, it is most likely that the watch movement has not been cleaned and maintained for a long time, resulting in oil stains in the watch and hindering the timekeeping of the watch. Or it is caused by water ingress into the watch.

If the watch does not go away due to water, you can directly wrap a small piece of calcium chloride or silica gel with gauze; Then take out the watch cover and put the calcium chloride wrapped in gauze and the electronic watch seal into a plastic bag and box. After waiting for half a day, you can take out the watch, and you can see the moisture of the electronic watch disappear. If the water ingress of the watch is serious, it can be left for a day.

Wearing the watch on the wrist for about two hours can also eliminate hand gas, with the watch reflecting inward and the bottom case of the watch facing outward.

If there are water droplets attached to the watch cover, it is easy to cause corrosion of parts and affect the accuracy of the time after a long time. In this case, you can wrap the watch tightly with several layers of toilet paper or moisture-absorbing flannel and bake it near a 40-watt light bulb (about 5 cm) for about half an hour, and the moisture in the watch will be discharged as water vapor.