The hard drive that I used for 2 months ticked and ticked

Your disk belongs to the basic phenomenon of bad sectors.

Description of the phenomenon 1Too slow when writing, too slow causes sound.

2.The sound caused by the hard drive being hot causes the space to rub.

First, copy the important files from your hard drive to your external hard drive or USB flash drive. Anyway, you have to keep the important documents yourself. Erasing the bad sectors will wipe out all the files on your hard drive.

Equal to advanced formatting. (The following is all about the operation when you remove important files, otherwise don't complain to me if any files are lost.) ）

Fix the operation flow:

1.Use the optical drive to read the disc with the DOS toolset.

2.Go to the DOS toolset, select and go to the MHDD software.

3.Select the hard drive. and press Enter.

4.Press F4 (Ready to Scan) and then F4 (Confirm Scan).

5.After scanning. Check for bad sectors.

The bad sector belongs to (unc or x) and the block point on the right. < 150ms is normal. > 150ms are abnormal, abnormal and unc (bad sectors) are erased with the following command.

6。Input: ERASE enters the erasing option, and the starting LBA value appears (if you don't understand, you can ignore him, press enter directly to skip).

And then to the end of the LBA value. (If you don't understand, don't worry about him, press enter to skip.) At the end there will be a choice, y n y for confirmation and n for denial.

Press y to select to start.

It's that simple. If you sweep the logical bad sector 2 times, it should be able to be solved, and if you wipe the physical bad sector a few more times.

Once you're done, let's partition it. After that, you can install the system, it's very simple. Ha ha.

If the problem hasn't been solved, leave me a message offline. I'll keep following up. If the problem is solved, give points. Add 100 points to me. Ha ha. Okay, after talking to you for so long, I'm going to work too.

I've broken a lot of hard drives with this software.

It is recommended not to use this software.

Go to a professional place and check it out!!

Disable HDTUNE!!

I think it doesn't matter what software reads the hard drive, as long as the hard drive sounds.

It's all because it's supposed to be a hard disk Bunsheng is a bit of a topic.,There should be something in the chuck, but it's not serious now.,Isn't there a replacement period for hard disks?

It's best to go early to change.

Seagate's hard drive is relatively loud, since you can't hear it if you don't listen carefully, it means that there is no problem. Don't be so nitpicky. Mine is also 500gsata used for a year, the noise can be heard without listening carefully, and there is no bad road.

Of course, if there is a physical bad sector, you can go to a dealer to exchange it.

Hard drive clattering and don't recognize the disk? Hello dear, it should be your hard disk has a bad sector or the disk is stuck caused by the hard disk clicking, generally we take a hard object to tap the hard disk a few times, so that it can be good. You can also do this, which can be fixed as follows:

1. After booting up, press F8 to enter safe mode, and then exit, select Restart or Shutdown to turn on the computer, and you can enter normal mode (repair registry). 2. If the fault persists, please use the system's built-in system restore to restore to the time when there is no fault (if the normal mode recovery fails, please boot the computer and press F8 to enter the safe mode and use the system restore). 3. If the fault persists, use the system disk to repair it, open the command prompt and enter sfc scannow Enter (there is a space between sfc and ), insert the original system disk to repair the system, and the system will automatically compare the repaired.

4. If the fault persists, set the optical drive in the BIOS as the first boot device, insert it into the system installation disk, press the R button, and select "Repair Installation". 5. If the fault persists, then the hard disk is broken and needs to be replaced. Hope it helps.

If my answer is helpful to you, please give a thumbs up (in the lower left corner), I look forward to your like, your efforts are very important to me, and your support is also the motivation for my progress. Finally, I wish you good health and a good mood!

Dear, hello, I'm glad to answer for you, the hard disk sound is generally caused by the abnormal sound caused by the abnormal sound caused by the collision with the shell caused by the abnormal action of the hard disk arm when moving, abnormal positioning, and the abnormal sound caused by the collision with the shell, or the magnetic arm or head of the hard disk is faintly damaged, such as the abnormal sound of screaming after the magnetic arm is broken, the magnetic head falls off or is deformed and misplaced, and the disk surface of the hard disk is in contact with the abnormal sound of screaming. In this case, most of them prove that the hard disk can only be scrapped in the circle, it is recommended to change the hard disk data cable first, and use MHDD to detect the bad sectors of the hard disk.

There are three main reasons why a hard drive is ticking:

1. When the computer hard disk makes a sound, it means that the computer has an abnormal situation, and the first thing to do is to back up all the important data in the hard disk to avoid greater losses.

2. Listen carefully to determine whether the sound of the drip hood is from the hard disk, sometimes it may be from the fan, or open the case to take a look, if the machine is a fan, it may be that the fan is aging or has too much dust, and it needs to be replaced or cleaned up.

3. Another most important problem is that the data cable interface of the hard disk is not in good contact, which causes the intermittent transmission of data and affects the normal use of the hard disk.

Classification of hard disks:

Generally speaking, Laosheng hard drives can be divided into mechanical hard drives and solid state drives. HDDs come in the form of drives that use traditional disk technology for data storage. SSDs, on the other hand, do not use traditional magnetic rails to read and write, but use solid-state storage technology, which can read and write data faster, and provide better performance and higher capacity.

Hello dear hard disk state destruction sound causes and solutions to the rest of the method is as follows: 1. First of all, at this time, when you hear the card ring, it means that your computer is abnormal. 2. There is also the sound of this squeak is not from the hard disk, it may also be from the fan, prick up your ears and listen carefully, or open the case box to take a look, if it is a fan, it means that the fan is aging or entering too much dust, and it needs to be replaced or cleaned up.

3. Excluding the fan factor, there are many reasons for the hard disk factor, the first is that the hard disk has bad sectors, mainly due to long-term use of aging, we can use the disk repair tool to repair the bad sectors. 4. Another of the most important problems is that the data cable interface of the hard disk is not in good contact, which causes the intermittent transmission of data and affects the positive use of the hard disk. 5. Another is that the power supply of our hard disk is insufficient or unstable, so we need to replace the power supply of the chassis at this time.

It is generally caused by the aging of the power supply. 6. If the computer is in a dusty, humid or high-temperature environment for a long time, and the hard disk itself is overaged, it is recommended to replace it with a new one and maintain a good and healthy environment.

The hard drive sometimes "clicks" inexplicably, and today I will help you solve this problem.

First of all, I checked the chip of the circuit board, when the fault appeared, I tried to touch the chip on the circuit board of the hard disk with my hand (first release the static electricity), the chip is not hot, and sometimes the hard disk can be read and written normally when booted, the chip should be normal, so it can be considered that the hard disk failure is not caused by a problem with the chip.

As we all know, when the hard disk works, it needs a stable voltage and sufficient current, if the voltage is unstable or the current is insufficient, the operation of the spindle motor will be affected, which makes it difficult to seek the magnetic arm, that is, if the power supply voltage or current of the hard disk changes too much, it will cause the change of the speed of the hard disk, and then there will be inaccurate positioning or error in the positioning of the magnetic arm, resulting in no normal reading of data or an increase in the bad sectors of the hard disk. The hard disk often makes a "click" sound, which may be caused by the abnormal operation of the hard disk and the continuous positioning of the magnetic arm due to the instability of the current.

Since the hard disk failed because of a problem with the chip, it may be due to the instability of the voltage, so I checked the voltage of the input and output of the hard disk. The power supply of the hard disk is 5V and 12V, you can use a multimeter to test, the voltage is too high and too low, and it is normal to have a fluctuation of 10. When the hard disk fault occurs, I carefully used a multimeter to detect the voltage at the interface of the hard disk, and found that the voltage is within the normal range, then it is not the problem of the power supply, then the problem is in the interface circuit of the hard disk.

Through the above analysis, it can be known that the problem of the sudden "click" of the hard disk is not caused by insufficient power supply or damage to the hard disk control chip, but by the poor contact between the hard disk circuit board and the magnetic arm power supply interface of the hard disk body. The part connected between the circuit board of the hard disk and the power supply of the disk body is not a pin or flexible cable, but a crimping method, because the hard disk is used for a long time, coupled with the poor working environment, the tin plating layer of the interface of the circuit board and the oxidation of the spring blade of the disk body, resulting in poor contact between the two, resulting in unstable power supply of the magnetic arm seek motor, and abnormal seek and the hard disk can not work normally.

Knowing that the problem of the hard disk may be in the **, then you can prescribe the right medicine, the solution is very easy, disassemble the four screws that fix the hard disk circuit board, carefully remove the circuit board (there is a line on the circuit board connected to the spindle motor, do not tear it off), pick up the circuit board, there will be two rows of spring pieces on the side of the circuit board close to the four-pin power interface, and carefully polish the contacts of each spring sheet with water sandpaper or a frustration knife. At the same time, the corresponding contacts on the circuit board should also be polished and bright, and then the circuit board can be put back as it is. Be careful to remove the grinding metal debris, otherwise it may cause a short circuit.

Finally, I tested it on the computer, and it was finally done, reinstalled the system on the hard disk, scanned and detected with Norton and other disk utilities, and found no errors, and then ran continuously for 12 hours without failure, and the hard disk will no longer have a big "click" sound (

The hard disk clicks, the computer is stuck, the bird cannot enter the system, the reading is slow, the hard disk is not in a hurry to scrap, just a screwdriver can be repaired.