Two hard disks ghost test, how to test two hard disks

Plug the first hard drive into the IED0 (or SATA0) connector on the motherboard. The second piece is arbitrary.

When you enter ghost and select a hard disk copy, 1-1 is the first partition of the first hard disk, and 2-1 is the first partition of the second hard disk.

It's the same with a full copy.

Do you give two hard drive partitions of the same size the same?

Do partitions all have the same names?

You change the name of the partition.

In English, it is not recognized under DOS.

It's simple. Look at the partition name.

Look at the size. Look at the file name.

Now make a ghost backup of all the data on the first hard disk, and then test the completed gho files to the second hard disk, and then delete the files on the first hard disk. Isn't that how you get to know each other? Teach you a stupid way to leave the second hard drive and unplug the power and data cables of the first hard drive.

This leaves only one hard drive. Got it

Do you want to bake it all or in a single dish Is there a brand of the two hard drives?

Set one hard disk as the master disk and the other as a slave disk.

Then use ghost to test the main disk to the slave disk.

No problem.,It's the first block in the host.,Just add it to the second block.,I was afraid of the same as you said before.,But the result isn't like this.,I promise.。 If that's not the case, come to my space and ask my ** to scold me.

In the disk you want to get into, create a folder at random, and you can see it clearly in the ghost.

In the disk you want to enter, just create a folder and pay attention to the hard disk partition and capacity.

Pay attention to the hard disk partition and capacity.

First of all, connect the two hard disks to a motherboard, set the hard disk of computer A as the main disk, and the hard disk of computer B as the slave disk, enter the ghost, and use the disk to disk inside to copy the hard disk.

You can copy hard disks under the Windows interface.

If it is a parallel port hard disk, you need to set the primary hard disk and the slave hard disk. Switch its master and slave disks through the pins on the hard inner disk (instructions are on the hard disk).If it is a serial port hard disk, the primary disk is connected to the first serial port, and the secondary disk is connected to the second serial port.

After booting into the system, if you copy the data, you can copy it from the disk as a normal partition. If you want to copy the system and engrave it, you need to run the ghost software on the system. For example, the hard disk version of ghost, ghost8, ghost11, etc.

Then it's the same as running the ghost tool under DOS.

Hello, this copy environment.

There is no problem with the test, you can use a software called "Easy Backup", which is still very safe and reliable for disk cloning. Our unit is also using this software...

Under the Clone bar, select Disk Clone. After that, just follow the prompts, it's very simple and convenient. The official website of disktool has relevant operation tutorials, and the precautions you mentioned are also mentioned above...

Two methods:

1. Enter the operating system to install one-click ghost, and then turn on the computer and select one-click ghost

2. Use a USB flash drive or CD to enter Ghost

It's actually quite simple! It's the first interface to choose one, the second one to choose one, the third one to choose one, see your hard disk don't connect the wrong one, it's that test that disk. That's it!

You can copy the disk, but you must first make sure that the capacity of the destination disk is sufficient and that the partition format of the destination disk is higher than or equal to that of the source disk. The source disk of FAT23 is connected to NTFS, which will make several other partitions unrecognizable.

When operating in ghost, select the first item: local All Partitions, and select Disk for all partitions

Then select to disk, select the source disk and target disk, and follow the prompts.

If you only need to use partition for the system, select to partition

Select the source and destination partitions and follow the prompts.

to image is used to make an image file to recover a form image is to recover a still image file.

Upstairs is right.

It doesn't matter what condition your hard drive is (unless it's broken), you can copy it.

Of course, the premise is that the small market pairs.

If your main plate is 80g, you can't get a small plate (less than 80g).

The capacity is different. Nothing else!

It is necessary to replace the original hard disk with a new hard disk to make the system partition.

Use ghost to make a mirror image of the old hard disk system partition and put it in another partition of this hard disk.

Then overwrite the image to the main partition of the new hard drive.

Yes, select the partition and you can do it.

The same size is fine.

Enter the ghost screen and enter all the way, so that the master and slave settings of the source disk and the target disk.

If the total amount of files is less than 160g, then you can take the test, whether it is 640g to 160g, or 160g to 640g.

It cannot be copied. Hard disk engraving can only be engraved on a small hard disk and a large hard disk, or the same engraving. Large and small are not supported. Because the engraving is the byte of each space on the hard disk, not the content in the space.

You can connect the hard disk that needs to be tested through the 3-port IDE data cable.,Note that the jumper and the ghost scene should be used to distinguish which one has data.。

If you have a lot of computers in the Internet café, you can use the Internet ghost.

Engrave the ghost image file on the disk, and copy it upwards with the disk, or you have to remove the hard disk and install it on a machine to copy it

Just use the backup file to install the system on another machine with ghost. The specific operation is to connect the hard disks of other machines and restore them one by one.

Directly copy the past with LAN through the Internet neighbor

The capacity of the target disk is generally not less than the source disk, both hard disks are connected to the computer, after starting the ghost into PE, select disk to disk, souse is the source disk, destination is the target disk, start after selection, and wait for the cloning to be completed.