How to set up the Nokia 7360 to surf the Internet and accept MMS?

MMS Settings:

Tools - Settings - Connection Settings - Access Points - Options - New Access Points - Use Default Settings:

Connection Name: Mobile MMS.

Data bearer mode: group data.

Access point name: CMWAP

Username: None.

Prompted for password: No.

Password: None Identification: Normal.

Homepage: http

2. Info - Options - Settings - MMS:

Access point used: Mobile MMS.

Internet Settings:

Menu Tools Settings Connection Settings - Access Points - Options Add Access Points Use the default setting connection name: CMWAP (you can take it at will).

Data bearer mode: group data.

Access point name: CMWAP

Username: None.

Prompted for password: No.

Password: None Authentication: Secure.

Home: Then press Options and select Advanced Settings.

Network type: IPv4

Nameservers: Automatic.

**Port Number: 80

It is easy to get all the problems with the mobile business hall, saving trouble and worry.

C7Please refer to the following settings.

Step 1: Please enter the GPRS parameter setting menu of your mobile phone; Step 2: Enter the following parameters in the GPRS settings menu

1. Homepage:;

3. APN settings (i.e., access points): CMWAP;

4. Gateway port number: Kaihe 9201 or 80;

5. Timeout limit: 600 is recommended;

6. Username setting: empty;

7. User password setting: empty and bright.

The non-staring wide pie is different from the mobile phone setting menu, and the specific setting menu can be understood through the mobile phone manual. You can also visit the Communication 100 service hall in person, which is set up by mobile customer service staff. After the setup is successful, you can call the customer service of the mobile phone brand** to learn how to use your mobile phone to log in to the network.

Mobile. I know that the team of Steel Seven Company will answer for you, thank you.

Landlord, you're too picky, you said you're going crazy, and the reward is only 0 You said it's a hole pin.

My homepage is.

My C6 also had this kind of staring situation before, and I didn't care that it was getting better, and I was depressed.

How to set up the Internet and MMS connection for 7610s.

1.Network Settings:

The steps are as follows: Settings - Configuration Settings - Personal Configuration Settings - Operations - New - Network Next, configure the network:

Account name: default (My Network), you can change it to your favorite name homepage:

Username: (empty) Password: (empty).

Use Preferred Access Point: Cancel.

Access Point Settings:

**Port: 80

Transmission mode: group data.

Transfer Mode Settings:

Packet Data Access Point: CMWAP

Network type: IPv4

Authentication Type: Common

Username: (empty).

Password: (empty) This way, GPRS is set to 2MMS Settings:

First of all, it is necessary to add a new

The steps are as follows: Settings - Configure Settings - Personal Configuration Settings - Actions - Add - MMS MessagesNext, configure MMS messages:

Note: You can't fill in the homepage of the network casually, otherwise the settings will be in vain) Use the preferred access point: cancel.

Access Point Settings:

**:Initiate.

Transmission mode: group data.

Transfer Mode Settings:

Packet Data Access Point: CMWAP

Network type: IPv4

Authentication Type: Common

Username: (empty).

Password: (empty).

OK, MMS is set up as well.

1. First set up Monternet

1 Menu Settings Connection Settings Access Points, press the option Add Access Point to use the default settings

2 Connection Name (Customizable) Data Bearer Mode (GPRS) Access Point Name (CMWAP) Username (None) Prompt for Password (No) Authentication (Normal) Home Page (http:

3 Options Advanced Settings Mobile IP (Automatic) Primary Nameserver (Not Selected) Secondary Nameserver (Not Selected) Proxy Server Address (**Port (80)

4 Return to Connection Settings GPRS GPRS Access Point (CMWAP) when required

5 Go back to the main Network option and set the default access point (set as the connection name mentioned in step 2).

6 When you're done, return to the standby interface, press and hold the 0 button for about 2 seconds, and see if you can go up to move Montnets!!

But what should I do if I can't send MMS messages yet? Proceed with the setup.

2. MMS settings

1 Menu Settings Connection Settings Access Points, press the option Add Access Point to use the default settings

2 Connection Name (Customizable) Data Bearer Mode (GPRS) Access Point Name (CMWAP) Username (None) Prompt for Password (No) Authentication (Normal) Home Page (http:

3 Options Advanced Settings Mobile IP (Automatic) Primary Nameserver (Unselected) Secondary Nameserver (Unselected) Server Address (Port (80).

4. Go to the Info option to set the MMS access point used (set to the connection name mentioned in step 2)!

Open the menu Tools Settings Connection Settings Access Point At this time, you create an access point named China Mobile MMS, and you can see the connection name - China Mobile - MMS data - bearer mode - GPRS, access point name: cmwap; Username: None. Prompted for password:

Not; Password: no need to change; Identification: Safety; Home:

Next, press Options - select Advanced Settings - and then change the **server address inside,**Port number 80, that's it, and then open the menu Info Option Settings MMS and set the access point used to China Mobile MMS and it's OK.