Konka TV42M3820AF needs to be equipped with a few M of broadband

Dear users:

Hello! Thank you for your support of Konka products! Konka network TV connection network use,In order to ensure the use effect and stability,It is recommended that you use the local mainstream broadband,4M or more network。 Thank you for your consultation and have a great day!

Dear users: Hello, thank you for your support to Konka! Konka LED42M3820AF TV networking, wired settings need to use routers and wired, and the relevant setting steps of routing segment are as follows:

1. The computer IP is automatically obtained, please check the computer manual or the after-sales telephone verification of the World University and Soran Vertical Computer. 2. Restore the router to factory settings and reset the router parameters. TV Setup Steps:

1、The TV is cut off and the power is restarted,2、Menu-Settings-Network-Wired-IP type automatic acquisition-Setting-Network detection。

For wireless networking, you need to use a wireless router, and it is recommended to use WPA encryption mode, which is set as follows: TKIP for password type, PSK ESK for PSK, and 8 digits for password. (It is recommended to use pure numbers for passwords, easy to identify) Please follow the above steps and give it a try; Thank you for your consultation and have a great day!

Konka TV LED42M3820AF is a network TV, which can be directly connected to the cable network to access the Internet, ** network TV programs. Here's how:

1. Prepare a network cable, insert one end of the network cable into the network interface of the TV, and the other end into the LAN port of the router.

2. Start the TV and enter the main interface of network TV.

3. Use the TV remote control to operate, find the system settings, and press the confirm button to enter.

4. After entering, find the network settings and press the confirm button to enter.

5. After entering, select the wired network connection, and set the TV to automatically obtain the IP address during the same virtual duration.

6. After setting, the TV will automatically recognize the input network signal and obtain the IP address assigned by the router.

Dear Konka with Liang Lihu:

Hello, thank you for using Konka products! LED42M3820AF is Konka Android smart network TV, according to the TV manual query this machine built-in wifi function. For networking, you can use a wired connection, or a wireless connection.

Please refer to the following steps:

1. For wired connection, please operate as follows:

1. Wired connections need to match: routers, network cables, computers, and network TVs;

2. First of all, the router and the computer can be connected to the network normally (please set the IP of the computer to automatically obtain first; After that, connect the computer and the router), and then connect one end of the network cable to the router and the other end to the network interface of the TV;

3. TV System Settings-Network-Wired Settings, IP Type Select Auto Acquisition, and finally click Set Rubber Cha Set.

2. For wireless connection, please operate as follows:

1. Wireless connection needs to be matched: wireless network card (this machine has built-in wifi), wireless router, computer, network TV rubber search machine.

2. The wireless router and the computer can be connected to the Internet normally;

3. TV system settings - network - wireless settings - built-in wifi selection to turn on - find the name of the wireless router at home, and then connect.

3. Note when the wireless connection cannot be connected:

1. The signal strength of the wireless network is too low (when the strength of the wireless network you use is less than 35%, although our machine can detect the network, it cannot be successfully connected.) In order to ensure the normal use of the wireless network, the signal strength is required to be stable at more than 70% or more than two bars. ）

2. When there is a wireless connection, you can search for a signal, but the connection fails, you need to check whether the encryption type, WEP length, and WEP mode settings are correct. Please confirm the parameters set by the encryption method,Our TV can be recognized normally:

a) Use WEP encryption mode, set as follows: open for authentication mode, 64bit for wep encryption, ASCII for key mode, any one key can be set, and the password needs to be set to 5 digits. (b) WPA encryption is adopted, and the settings are as follows:

Set the password type to TKIP, select psk for PSK EAP, and set 8 digits for the password. (Note: The password is recommended to use the number 0-9 for easy identification of the TV).

Please follow the above steps, re-operate, try it, if the operation is not successful, please feedback to the customer service of Konka official**: **, and the customer service staff will serve you wholeheartedly.

Dear users, Hello! Thank you for your support of Konka products! Konka LED42M3820AF TV can be connected to a notebook through an HDMI cable to display the TV as a computer. There are a few things to be aware of in the connection:

1. The resolution of the computer should be within the range of the TV (such as 1024*768, etc.);

2. The refresh rate of the computer should be 60Hz;

Both of the above points require the user to right-click on the advanced settings in the "Properties" on the desktop of the laptop or desktop computer).

3. Turn on the TV first, select the TV signal in HDMI (select the dialog box that pops up according to the remote control menu of the TV, the computer signal source displayed by different TVs is different, if there is an option in the TV menu "computer", select the computer) state, and then start the computer host to let the TV automatically identify the signal of the computer. (Note: Do not turn on the computer first and then turn on the TV, that may not have a picture).

Please follow the above steps, re-operate, try it, if the operation is not successful, please feedback to the customer service through Konka official**: **, the customer service staff will be dedicated to your service guidance. Thank you for your consultation and I wish you a happy life!

The notebook can be connected to the Konka TV in the following steps:

1.First, use HDMI to connect the computer and TV to Tuchang, and connect to the HDMI port of each device.

2.If there are multiple HDMI ports on the TV, the display source of the TV switch should be adjusted to the corresponding HDMI port.

3.Right-click on the desktop on the computer to select the screen resolution, and you will see that there is a detection function, and you will find multiple monitors when you check it. Then tap Connect to projector and you're good to go.

Dear Konka users:

Hello, sorry for the inconvenience caused by Konka products! For the use of LED42M3820AF network TV in your home network disconnection, 1) to ensure the normal and stable network environment of the home network environment, it is recommended to use the mainstream network of local travel (such as telecom broadband, etc.);

2) Under normal network conditions, you can adjust the "DHCP system renewal time" in the routing spike to the maximum, and try to connect to the TV again.

What kind of network cable is yours?