Konka network smart TV how to connect to the network is always dropped

There are two types of ways to connect Konka smart TVs to the network, one is a wired connection, and the other is a wireless connection. In fact, as long as you follow the installation steps and get it done step by step, this situation rarely happens.

Wired connection: 1. The wired connection needs to match: router, network cable, computer, and network TV.

2. First of all, the router and the computer can be connected to the network normally ( When wired connection, please set the IP of the computer to automatically obtain; Connect the computer and the router, log in the router, generally on the back of the router, such as: etc., after entering the **information,), connect a network cable to the router at one end, and connect the network interface of the TV at the other end.

3. TV menu - network settings - wired settings, IP type Select automatic get, and finally click Settings.

Wireless connection: 1. Wireless connection needs to be matched: wireless network card (wireless network card needs to be purchased and matched by the user, if the built-in wifi does not need a wireless network card), wireless router, computer, network TV.

2. After the wireless router and the computer can be connected to the network normally, please connect the wireless network card to the TV (no driver, can be installed and used directly).

3、TV menu-Network settings-Wireless settings-SSID(Search for router devices)、Encryption type(Same as set on the computer)、IP type Select automatic acquisition,Finally, click on the setting to set upIn addition,The wireless router settings that our TV can recognize are:Adopt WEP encryption method,The settings are as follows:The authentication method is selected open, WEPencryption is selected64bit, the key mode is selected ascii, the key can be set to any one,The password needs to be set 5 digits。

WPA encryption is used, and the settings are as follows: TKIP is set to password type, PSK ESP is set to PSK, and the password must be set to 8 digits.

According to your description, the machine is often disconnected from the network, it is recommended to exclude the following points: :(1) to ensure the normal and stable network environment at home, it is recommended to use the local mainstream network (such as telecom broadband, etc.); (2) Under normal network conditions, you can adjust the "DHCP system renewal time" in the router to the maximum, and try to connect to the TV again. If there is still a fault after operation, you can consult through the official WeChat**, and we can answer you in detail at that time.

Konka enterprise knows that to provide you with high-quality solutions, attentive to answer your questions, hope to be able to get you.

If you are sure that it is really a crash, then you can wait for a while and when the processor reacts, you can proceed.

There is also the fact that the operating system of the TV is broken, which is not something that can be solved by just waiting. This requires turning off the TV first and then re-flashing the TV's operating system.

Or a USB flash drive. Among them, you can flash the computer through a memory card or USB flash drive.

However, if you don't know how to brush the machine, then don't brush it yourself, you can go to the after-sales or maintenance department to brush the machine to solve the problem.

Konka TV crashed,If the restart is not successful,After-sales warranty is required,You call**Go to the repair point,Let him come to repair,If it is an online purchase TV,Contact the store and send it back to the manufacturer for warranty。

Hello! Based on your feedback; It is recommended that you try it out after the TV is powered off. If the problem is still so, you can log on to Konka's official website** to register for repair, and after-sales will arrange technicians to come to you to deal with it.

How to connect Konka LCD TV to wireless 1、Turn on the TV and enter the main interface of the TV。 2. Use the remote control and select the "Settings" button to enter the network settings interface. 3. Select the "Wireless" tab below, and you will enter the wireless selection interface.

4. Use the remote control to select the wireless route you want to connect to, and pop up the password verification interface. 5. Enter the wireless routing password and click the "Connect" button. 6、After clicking "Connect",The TV begins to connect to the wireless network,Later we return to the main course menu,See the following interface,It means that the wireless connection has been successful。

Take a look.

The TV is dead, then you can turn off the TV, or unplug the power, and then force it on, maybe it's good, it can be used normally, it's really not good, you can only find a professional to repair it.

Konka TV is dead,You can unplug the power,Try to restart,If there is still no response, you can find a maintenance person。

When the TV freezes, you can operate it in the remote control, and then wait for the reaction, see if there will be a response after waiting for a while, if there is no response, unplug it, and turn it back on.

Unplug the power cord, wait a few minutes, and then plug in the power cord and turn it on to restart.

Unplug and plug it back in and on again.

Generally, if the TV crashes, it is recommended that you turn off the TV directly and then turn the TV back on.

Summary. It may be that the network is not very stable, and it is recommended to reconnect to the network. There are two types of Konka TV connection networks:

wired connection; Wireless connection (wifi). Method 1: Wired connection 1

Plug one part of the network cable into the LAN port of the router, and the other end into the network port on the back of the TV. 2.Turn on the TV, and there is a wired network connection symbol in the upper right corner of the screen, and the connection is complete.

If the connection is still not successful, check if the router is working properly. Method 2: Wireless connection 1

Turn on the TV and tap Network – Wi-Fi in the settings. 2.Select the wifi you want to connect to and enter the corresponding password.

The display connection is successful, and all of them can allow Konka TV to travel to the network. The above two methods can make your home Konka TV easily connect to the Internet.

The Konka IPTV I bought suddenly couldn't connect to the network What's going on.

Hello, I have seen your question and am sorting out the answer, please wait for a while It may be that the network is not very stable, it is recommended to reconnect to the network. There are two kinds of Konka TV connection networks: wired connection; Wireless connection (wifi).

Method 1: Wired connection 1Plug one part of the network cable into the LAN port of the router, and the other end into the network port on the back of the TV.

2.Turn on the TV, and there is a wired network connection symbol in the upper right corner of the screen, and the connection is complete. If the connection is still not successful, check if the router is working properly.

Method 2: Wireless connection 1Turn on the TV and tap Network – Wi-Fi in the settings.

2.Select the wifi you want to connect to and enter the corresponding password. The display connection is successful, and all of them can allow Konka TV to travel to the network.

The above two methods can make your home Konka TV easily connect to the Internet.

It is now the case.

Let's do it as you want.

It still can't see <>

How do <> see if the router is working properly?

Turn it off and turn it on again. Turn off the net as well, and it should be turned on again.

Dear,For you to find out if the Konka TV intranet connection is abnormal, the solution is to first check whether the router is successfully connected to the Internet network,Then optimize the TVDNS。 Then enter the TV main scum page,Find the system tab,Open the network information in the TV manager,Select DNS settings。 If you can't find the DNS settings of the TV box,The easiest way to talk about Fang Rufan is to open the dangbei market to find management。

Select the network operator used by your car in DNS optimization,Select the province where the actual status of the TV is located,Then click to confirm,The specific solutions are as follows: 1The network settings of the TV are caused by problems; You can enter the network settings interface and try to connect to the wifi signal at home again. 2. If there is a problem with the router setting or the router is faulty, you can restart the router to solve it; Or restore the router to factory settings and reset the network parameters to solve the problem; If the router hardware is faulty, you need to contact the after-sales service for maintenance or replace the router to solve the problem.

3. Whether the network line and server of the network service provider are interrupted or faulty, and the router cannot connect to the network, in this case, the TV will inevitably be disconnected, and it is necessary to contact the network service provider to solve the network transmission problem first. 4、It may be that the network is abnormal due to the problem of the TV system,You can restart the TV to solve it,If necessary, you can enter the system settings interface,Restore the system of the TV to the factory setting state or upgrade to the latest version to solve it。

Summary. Why is Konka TV's wireless network disconnected?

1. Unstable signal: The signal of the TV wireless network is affected by the environment and distance, and there may be disconnection problems. 2. Insufficient memory:

Running out of memory space can also cause the wireless network to drop. 3. There is a problem with the setting: If the setting is incorrect, it will also cause the wireless network to be disconnected.

4. Router failure: If the router fails for a long time or for other reasons, it will also cause the wireless network to be disconnected. 5. Other reasons:

Unknown Bluetooth devices, radios, etc. nearby can also cause the wireless network to be disconnected.

Why is Konka TV's wireless network disconnected?

Why is Konka TV's wireless network disconnected?

1. Unstable signal: The signal of the wireless network is affected by the environment and distance, and there may be a problem of disconnected ridge attack. 2. Insufficient memory:

Running out of memory space can also cause the wireless network to drop. 3. There is a problem with the setting: If the setting is incorrect, it will also cause the wireless network to be disconnected.

Fourth, router failure: long-term use or due to other original router failure, will also cause the wireless network to be disconnected. 5. Other reasons:

Unknown Bluetooth devices, radios, etc. nearby can also cause the wireless network to be disconnected.

Konka TV performance is very good,The appearance design is more fashionable,The display effect Sun He is also very clear,Using4K Ultra HD resolution technology,Single brightness is stronger,Clearer picture quality,There are9Gray scale,High color contrast,Strong color expression,Energy saving and environmental protection,Smooth operation,The sound effect is also very good,The functionality is also very powerful,Strong insight,Update the fast answer type on the staring system,Support one-button operation,The operation is very convenient,Overall,Konka TV is very cost-effective, It is a more trustworthy TV brand, and it is worth recommending to buy.

The Konka IPTV I bought suddenly couldn't connect to the network What's going on.

Hello, the Konka network TV I bought suddenly couldn't connect to the network What's going on? It should be that the router was not connected properly. 1.

Turn on the TV and enter the main interface of the TV 2Using the remote control, select the "Settings" button to enter the network settings interface 3Select the "Wireless" tab below to enter the wireless selection screen 4

Use the remote control to select the wireless route you want to connect to, and pop up the command verification screen 5Enter the wireless routing password, click "Connect" and press the Rubber Mouse button 6After clicking "Connect",The TV begins to connect to the wireless network as in the middle,Later we return to the main course menu,See the following interface,It means that the wireless pin has been connected successfully。