What should I do if the hard disk is missing 100g and the hard disk memory is missing by more than 3

I want you to ask this question.

First of all, you need to know how to look at the capacity of your hard drive.

Here's how to do it: First: When you boot the computer, go to the BIOS to view. Add your hard drive to be 500g. Look at it in the BIOS at this point.

It should be an accurate 500g.

Second: Use the hard disk detection tool MHHDD to check.

Run MHDD under DOS

Enter the ID after entering.

The parameters of your hard drive will be displayed accurately. This includes the capacity of the hard drive, of course. At this time, it should also be 500g.

Third. Check it out once you're in the system.

You need to use some software.

For example: everst. Master Lu. Drive sprites and more.

If the system is normal.

It should also be 500g in the hard disk parameters.

If. If you're in the system.

Add the parameters of each system partition.

Generally, it does not reach 500g

Why? Because the hard drive partition is formatted. It will take up some space on your hard drive.

Due to the different modes of operation.

Generally, a 500G hard disk is between 470 and 480 G, which is considered normal.

Your question says that the hard drive is missing 100g

You can follow the above method to check the actual capacity of your hard drive first.

Then add up the partition capacity of each system in the system.

If the error is greater than 100g.

There are two reasons for this: first.

Your hard drive comes with hidden partitions.

Second. Your hard drive is not partitioned well when partitioned. At this point, repartitioning is sufficient.

A little advice. Hope that helps you :)

Right-click on the hidden 100g partition, select "Delete Volume", and then "Add Simple Volume".

If it is a brand machine, it may have made a hidden partition of the system. If you don't need it, you can use the partition work to repartition it all and it will be displayed.

The manufacturer's factory hard disk is calculated at 1000kb, and when we use the hard disk, it is calculated at 1024kb.

A 10G hard drive is generally only about 9G. And so on, your hard drive should be 1t.

Summary. 1. I'm not sure what the specifics are.

2. If you sell a class such as a 1T hard disk, it is normal to have a 30G less.

What to do if the hard disk memory is less than 30 g.

1. I'm not sure what the specifics are. 2. If you sell a class such as a 1T hard disk, it is normal to have a 30G less.

It used to be more than 1890 G, and now it suddenly becomes 1863 G, and now it can't be recognized on the computer, and it shows unallocated after entering Disk Management, how to solve it?

How to recover partitions and files with DiskGenius.

Let's go and learn, supposedly there is a problem with the partition table.

It's just which one to press.

**Learn the content yourself.

This software is only used after honest study.

Is there any other way besides this method? He has a save change that costs more than 200 yuan, but more than 200 yuan can buy a hard disk.

You can find a cracked software to try it. Actually, I use these software are cracked versions.,Supposedly, the cracked version shouldn't have this thing.。 Because these software are almost only used at the time of installation.

Usually rarely used, only know that the problem is found, and there is not much practical experience, because almost never encountered! And there are a lot of these similar software, the owner can't find the west, you can take the time to search for it.

The reasons and solutions for the 300G hard disk showing only 5MB are as follows: First, after PE boots, the computer does not find the hard disk correctly, and it is more likely that the SATA controller mode in the BIOS is set to AHCI. In this case, the PE does not actually show the hard disk, the 5MB hard disk is actually a virtual hard disk created when the PE system is running.

Set the SATA controller mode in the BIOS to the IDE and the hard disk will be displayed normally. Second, the hard disk is damaged or not installed or damaged, resulting in the wrong identification of the hard disk, this problem may also occur, which is characterized by the display of the shadow fear model is very long, very strange, in this case, it is recommended to reconnect the hard disk carefully and try again.