The router management interface cannot be logged in

To reset the settings, press the reset button on the closing side of the router The manual teaches you how to restart, such as long press the reset button reset for 1-5 seconds, then unplug the router, and then release the reset button and reset button.

Replug in the power of the router, the network cable can be connected first, but your computer must be connected to the network cable of the router, then turn on the computer, open the browser and enter in the address bar and press enter, and you will enter the routing management interface, so that you can follow the wizard inside to set up! If that doesn't work, just connect all the wires correctly and re-debug! That is, the network cable enters the line through the cat and then to the router and then to your computer, and the cable should not be plugged in wrong!

1.You need to change the IP address to auto-assign.

2.If Auto-Allocate can't get the assigned address jump to 33Change the IP to and enter it in your browser.

4.If 3 can't get in, skip to 5

5.Change the IP to and enter it in your browser.

It will generally be resolved.

If it doesn't work yet.

Press the router's reset

Restore to factory settings, then log in to the router, reboot a few more times, and open the web page after each reboot to try.

Personally, I think it might be a router issue.

Summary. Hello dear, it is a pleasure to serve you. After the router is connected to the Internet, it can't enter the management interface1First of all, you need to check the background address of your router. That is, the gateway address of the router. The background address of different routers is different.

After the router is connected to the Internet, it cannot enter the management interface.

Hello dear, it is a pleasure to serve you. After the router is connected to the Internet, it can't enter the management interface1First of all, you need to check the background address of your router. That is, the gateway address of the router. The background address of different routers is different.

The router is turned on and the mobile phone enters the router management interface, nothing else is set, only the router is set to connect to the network, restart the router, and the mobile phone can connect to the router wifiInternet access is also normal, but you can't get into the management interface of the router, after entering the address, the phone always goes to the Internet to find this address, not into the router management interface.

3.Then enter the gateway address into your phone or computer browser, which is the background address. You can successfully enter the background of the router to set up.

4.If the gateway address is correct, you still cannot enter the background. Then it is likely that there is a fault in the background of the router, and it is recommended that you turn off the power and restart the router.

Or press and hold the restart button of the router to restore the router to factory settings. If the router is still unable to enter the background after resetting its factory settings and making sure that your background address is correct, then the router is faulty and needs to be sent to the after-sales service for maintenance or flashing.

I started my phone to be able to get into the router.

You can first see if your gateway address is correct, and if the gateway address is correct, you can enter it before.

Then it is recommended that you restart your phone, or change your phone to a new browser. It is to re** a new browser, because some browsers have caches, resulting in a stuck background address. And reboot your router and try again.

I also encountered this situation, after trial and error, I found that the browser has started the security protection function, and I will not set the browser, and I can log in if I change the browser, I hope it can help you.

1.First of all, the IP of the computer should be set to a network segment with the router, and the network segment of the route can be seen in the manual, which is generally or, and the gateway is also set to the same, generally or.

2.Then enter the gateway address in the address bar of the browser and press the enter key, and then enter the username and password after the dialog box comes out.

3.If you don't see the dialog box, it means that the IP address is not set to the right or the address IP in the address bar is not entered correctly, note: when entering the IP in English, that is, you need to use the half-width input method, the IP address of the computer can not be obtained automatically, you should use "use the following IP address".

Ready-to-use, it is explained in the general manual.