The company is all routers to the Internet, and if you want to change the switch, how to install it?

ok!First of all, to correct your misconception, there is not much difference between using a home route and using a switch, and there can only be a difference in latency of a few milliseconds.

Then we need to solve this situation of network congestion because someone **, then we must use Qos, you can first see if there is a QoS function in the existing route, if not, then you need to buy a route with QoS function.

Speaking of QoS, if there is a route with QoS function, then at the total exit point of the network, use the route with QoS function.

Then all you need to do is set up accordingly, first calculate the number of computers, then calculate the average bandwidth not used, and then you need to bind the IP and MAC address of each computer, and then configure it according to your needs.

If the bandwidth of each computer is very low after the bandwidth is evenly divided, it is recommended to upgrade the bandwidth.

In general, the uplink needs to maintain a certain degree of redundancy, and the downlink bandwidth can be close to the maximum bandwidth, so as to ensure the smoothness of the network.

The switch can't solve your problem, your problem should be the bandwidth control problem, buy an enterprise-level router with bandwidth management function is better, the management function is a little more powerful, look at the technical manual, configure it, upgrade the network speed?? Hehe, people's desires are unlimited, and some people ** blue light, 1m per second is too slow.

You don't need to change switches, just limit the maximum bandwidth usage of each IP in the route.

1. From the light bai

The cat comes out with a network cable and plugs it into the WAN port of the DU main router, and ZOs carry out the network.

DAO network settings; The first floor, the second floor, and the third floor are directly connected to the network wall box with a network cable. The router on each floor is configured like the living room, which can be connected to wired as much as possible, and other digital network equipment is wireless.

2. Network settings: first set the main router, after connecting the power supply, press the above reset button for about 10 seconds, and the above indicator light flashes all, which means that the reset is successful. This wired gigabit router also has access to dual-channel broadband.

3. Dial up or fix IP Internet settings, open the browser: enter in the address bar, and first create your own user password.

4. Choose the way to go online, generally PPPoE dial-up networking, or automatic acquisition, or static IP.

The PPPoE number is, broadband & fiber, with account number and password.

The automatic acquisition is: DHCP, which is usually a network cable directly down from the switch.

Static IP address refers to the fixed IP address that is directly given to users by broadband vendors.

5. After the configuration is completed, remember to confirm whether the router has DHCP service turned on, which is generally turned on by default.

1. First of all, log in to the router management interface, enter [Wireless Settings] - Basic Settings], modify the SSID, and click Save. Genus 2, after that, in [Network Parameters] - LAN Port Settings], modify the IP address, which is not the same as the main router, and then click Save.

3. In the pop-up restart dialog box, click OK and wait for the restart to complete. This is important.

4. Finally, according to the application topology diagram, connect the LAN port of the TL-WR841N (i.e., interface 1 and 4) to the LAN port of the front-end router. The method is simple.

Let's talk about wiring first

1. ** line through the junction box to du** and cat, zhi2, cat out of line to.

DAO router.

3. Any port of the router LAN can accommodate one network cable to the 1 port of the switch, and any network cable can be sent from the switch to the computer.

Here, as long as the router is set up to automatically dial, the line can be used directly, and the switch can only be identified and exchanged, part of the layer.

Can be used together.

As we all know, broadband login requires an account and password, and the router can automatically save the account and password for broadband login, which is convenient for users to log in to broadband every time they use it, and can separate the broadband from several computers.

The switch is to divide a broadband into ten, dozens or even hundreds of computers, but it does not have the function of automatically logging in to the broadband account.

Generally, small companies, enterprises with dozens of people will first use the router, and then connect the output broadband cable of the router to the switch, and use the switch to separate dozens of computers. It's very convenient.

Just buy a switch, and an Internet café is like this, a small router, set a speed limit, and then deliver a big version.

You buy a switch directly and then buy a switch as a computer like the previous one, and connect it to the router 1 2 3 4 5 upper hole can not be connected to the wan

The model number of the switch and the router, what you said is too vague, is the switch a fool or a network manager, is it a layer 2 or a layer 3, you can put the model number of the device on it, and it will tell you how to get it.

Swap B and A (A can be dispensed with), connect the network cable to B's WAN port, set the same as before, and turn on DHCP. Your computer can be plugged into the LAN port, and your mobile phone can be wirelessly accessed.

Connect the network cable from Router A to Router B, and then set it up. Use your router to set up a Wi-Fi network.

Settings:1First, connect the computer to the LAN port of the slave router, and change the IP address of the slave router to a different network segment address, as long as it is not in the same network segment as the main router. For example, most router addresses are, and we just need to change from router address to one;

2.Then turn off the DHCP function from the router in the settings;

3.Finally, connect the network cable from the main router to the LAN port of the slave router (any one is fine), note that it cannot be the WAN port.

This method can be connected to 6 computers at the same time!

Pull the line from the outer bedroom and connect it to the lan port, and you're done. Your network cable is also connected to the LAN port. Just set your NIC IP address to get it automatically.

Try to change the IP of several computers to static.,And the IP of the router.,Don't be the same as the settings of the system server.,For example, people are.,Your router is changed,,,How many of your computers are changed.。。。