My computer has a wireless network why can t I get a wireless network lp address 5

There are three reasons:

1. Wireless network attribute setting.

2. The IP protocol is not installed on the NIC, or the protocol is incorrect.

3. Router setting problems.

The corresponding solutions are as follows:

1. Wireless network attribute setting. "Control Panel > Network Connections > Wireless Network Connection Properties > Verify uncheck the box in front of "Enable verification for this network" (see below if there is no verification tab).

2. The IP protocol is not installed on the NIC, or the protocol is incorrect. Click Local Connection Properties. In the General tab, click Install and install all the clients, services, and protocols.

3. Router setting problems. First connect to the wireless router with a local network card, open the router settings, and the "setup wizard" of the router to access the Internet can be wired to indicate that there is no problem with the router's Internet access, and the DHCP server option is set to enabled, so that you don't need to set the IP, and then set the wireless parameters, set to turn on the wireless function, and the security settings are not set.

First of all, check if the phone has wifi turned on

If it is turned on but still cannot connect, you can use your computer to set up WiFi, such as 360WiFi or restart your phone.

The above is still not feasible, you can go to the place where the mobile phone is repaired to see if the mobile phone wifi receiving device is faulty.

Your computer's wireless network is your computer's wireless network card! Do you have a router? Or there are hot spots!

Check if the wireless network shared by your computer is set up correctly?

It is possible that you may not be able to get the correct IP address, so in this case, you can restart your phone and computer and share the IP network again.

Did you use a wireless router?

It may be that the wifi of the mobile phone is not very easy to use, it is recommended to brush off the machine (or hard once), or it is not practical to use the wifi connection that comes with the system, and the next applet.

2.Considering whether it is a problem with the router settings, you can use other computers or mobile phones to test?

3.Go to the business hall and ask someone to try the reputation for you.

Reason: If there are too few IP addresses allocated in the DHCP server address pool (for example, only one or two), and the time in the address lease period is set too long, it will cause the mobile phone to disconnect from the wireless router and reconnect again because the IP address search and destruction section in the address pool has been occupied, and the rental period has not expired, the router will not be able to assign a new IP address to the mobile phone, and can only be reassigned again after the existing IP address rental time has expired. So the phone will be getting the IP address all the time.

Restart the router first, if you can connect after restarting the router, you can try it according to the following method (the following is what I summarized after tossing for a long time, my connection is no problem now, you can try it). Go to the router interface and open the DHCP service option, and change the time in the address rental period to the shortest (1 minute) to try it.

One is a computer problem, and the other is a mobile phone problem.

At present, all smartphones automatically obtain IP addresses by default, and the IPv4 settings of routers also automatically obtain IP addresses. If the phone is stuck in the process of getting the IP address. Install the file manager on your phone, install the root explorer, delete the two files in the data misc dhcp, and try again.

Install the file manager and click to enter (as shown below).

Enter the Data Misc DHCP (as shown below) <>

You can also set the static IP address of your mobile phone by yourself, click the lower right button on the phone, pop up the menu, and click "Advanced".

The mobile phone page pops up, and select "Useful Static IP".

If the repair is successful, it is not a problem with the computer.

<> fill in the mobile phone exactly the same as the gateway and DNS, the IP address should be changed, and the last digit can be changed between 1-255 (for example, the address on the computer is, then your mobile phone is set to the last digit 3 can be changed between 1-255 at will, After setting, connect to wifi from the mobile phone, and connect it (Note: the computer and mobile phone must be a local area network).

Hello, first of all, thank you for your support to China Telecom, according to your description, turn on the DHCP of your router, and then assign a fixed IP to the mobile phone Click on the network link on the lower right side of the computer, enter the network sharing center, select Manage Wireless Network, click Add, select "Create a temporary network, select Next, fill in the network name as you like, (Note: must be an English name) Security Type: Please select No Authentication (Open) (Note:

This option can be left unpassworded) If you want to set a password, select WEP, the password is 6 digits and 8 digits (preferably numbers), and finally click Next to complete the creation! Close all pages, click Network in the tool bar in the lower right corner of the computer desktop, the new wireless just now appears, click Connect, return to the Network and Sharing Center, click Change Adapter Settings, select all local connections and wireless network connections, and right-click to bridge. After the bridge is successful, a bridge will appear.

Hundreds of mobile phones are low prices on the whole network

Have a great day!

See if the router DHCP is turned on...

You can also look at the IP range of your computer... Give your phone a fixed IP

It's best to put it out and then turn on the DHCP function.

Problem Analysis:

1 The network cable that the landlord connects to each user must be routed, otherwise your laptop will not be able to access the Internet directly. But if your phone wants to go online, it has to go through a secondary route.

2. You directly connect the network cable to the LAN port of the router, which only turns the router into an ordinary hub, which meets the needs of the laptop to surf the Internet, and only achieves the effect of secondary splitting, but does not play the role of secondary routing.

3 Although you have set the router connection mode to dynamic connection, the setting does not work because you are connected to the LAN port, not the WAN port.

4 The result of the landlord's operation is that the laptop can access the Internet, but the mobile phone cannot, because the mobile phone needs to use the SSID function of the router, and although the router has turned on the SSID, because it is connected to the LAN intranet interface, it can only search for the signal, and cannot log in to use.

Solution: Connect the introduced network cable to the WAN interface of the unlimited router, set the interface to dynamic, (or set it to fixed according to the fixed IP mask provided by the landlord) Turn on the unlimited function of the router, turn on the SSID broadcast, and then turn on the WiFi hotspot of the mobile phone to access the Internet.

The analysis of zjxlrong is correct, and the WAN port must be connected. All that's left is to figure out how to set up the landlord's higher-level route, so that your WAN port can get the IP address. It should be noted that the landlord router is not bound to your MAC address, and you can't get the IP if you switch hosts.

Take a look at your router, can you clone the host MAC address, impersonate the identity of your laptop, and then you can surf the Internet.

Check to see if your wireless router is set up to connect to the Internet on only one device.

Try a different router、I suspect it's a problem with the router。

Here's how to fix it:

2. Then click on the entry and select the item "Modify Network", as shown in the following figure

3. Then enter the dialog box to enter the password, and check "Show advanced options", as shown in the figure below

4. Then select the "Static" option in the "IP Settings", as shown in the figure below

5. Finally, set the following parameters, set and save, and reconnect to the wireless network.

Open Settings - Wireless & Network - WLAN Settings, press the Menu button, enter the Advanced Options Settings, and tick in the IP settings"Use a static IP"。

And then again"IP address"""Generally, households use wireless routing, and the network segment is, and the range represented by the X value is between 2 and 255.

And then again"Gateways"Either the two gateways depend on the IP address of your wireless router. "Netmask"in, in"Domain name 1""

Domain name 2"is also known as the Domain Name System

1. Check to see if the router DHCP is turned on. Here's how to configure DHCP:

1) Enter the router address in the browser, the address of each router model is different, you can check the router manual, but they are all the same, here use the tp link router operation screenshot to explain, use this router account and password to log in to the router.

3) First of all, enable the DHCP server, define the IP address allocation range of the DHCP server, the IP address leasing cycle, and do not need to fill in the other special needs. Click Save.

2. In addition, you can also look at the IP segment of the computer, and then assign a fixed IP to your mobile phone.

Please make sure that the IP address of your mobile phone is obtained, and the wireless signal SSID number and password are the same as those of the computer, and it should be able to be used normally.

Check out these items.

You go to the router settings interface to see if the DHCP server is open.

You're going to set up wap wap2

and then set a password. Then the phone to find the wireless network is required to enter the password you set. That's it

First, make sure your router is set up correctly.

1. The problem of setting the IP address of the computer.

1) When connecting to the router to surf the Internet, you need to set the IP address on the computer to be automatically obtained (dynamic IP).

Dynamic IP address configuration of the computer.

2) If the administrator of your network requires a fixed IP address to access the Internet, please fill in the correct IP address, subnet mask, gateway and DNS server address in the local connection.

2. Check whether the network is normal.

1. First of all, open PC Manager and select the toolbox in the lower right corner.

2. Select the network repair tool.

3. Click Fix Now.

This slippery situation of the landlord can be solved in the following ways:

1. Turn off and open the back cover of the phone, turn off the phone and take out the battery, install the battery and restart the phone later, and refresh the phone data;

2. Clean up your phone's running memory. There will be a file management system on the mobile phone, which can be opened to find the file and then clean it;