How to paste the mobile phone screensaver so that it does not bubble 10

How to keep the screen saver of the mobile phone without foaming:

1. Wipe the screen clean with a cloth first, and remove it with a dust removal sticker if there is stubborn dust, a dust removal paste may not be enough, this is the key to the problem.

2. Tear off the protective film of the second standard first, paste it on the screen and then tear it off, the film of the second layer has paste, and the dust removal effect is not worse than that of the dust removal sticker, and it is a large area of dust removal, which is not the same as the general film method here.

3. Tear off the film of a label, aim at the screen film, press and hold one side of the cardboard from top to bottom, and the small bubbles can be squeezed off with your fingers.

Prepare a facial tissue, don't open it, don't remove the screensaver first, uncover a little and fix it on top of the phone.

Then wrap the tissue around your index finger and wipe the screensaver and you're good to go.

Shine oil''It can play a role in cleaning the screen.

You can polish the screen very brightly.

But wipe it dry when you put on the screensaver.

Otherwise, the screensaver will not be attached.

You can rub some girls on the screen that girls often use"Shine oil''(The kind of spray, not too much, just a little.) After attaching it, use a cotton cloth to gently wipe off the air bubbles (no awkward protective film).

My point of view, ministry post. It's more ugly to stick on that thing than not to stick it, so you just need to pay more attention to it, there's no need.

If your phone screensaver is often torn off and pasted on, it will naturally blister. No matter how much you stick it, it will blister. Or you buy another screensaver.

The environment should not be too hot, preferably in winter.

mm told the even-drop.

The steps to remove the bubbles from the mobile phone screensaver are as follows:

Materials required: scissors, tape, small cloth.

1. First of all, if there are air bubbles on the screensaver, first use a small piece of cloth to remove the squeezable air bubbles. Fold the cloth a few times and use the cloth to push the bubbles towards the edge of the screen.

2. The remaining bubbles that cannot be pushed off are because there is still dust on the membrane, and the dust adheres to the membrane to form bubbles, and the dust bubbles can be removed by taking the dust out.

3. Cut the scotch tape one to two inches long, stick it next to the bubbles on the film, and then cut a small piece of scotch tape with the sticky side facing up.

4. Pull up the scotch tape attached to the film opening fiber with one hand, and pull up a slit to let the tape in the other hand.

5. When the protective film is pulled apart, you can see whether there is dust on the film or on the mobile phone screen. The dust is small, and then the dust is glued to the other side with scotch tape.

Notes:

It shows that the mobile phone comes with a film at the factory.

1. Hard card or bank card.

If there is a small amount of air bubbles on the edge of the mobile phone tempered film, first pry the corner close to the bubble with a hard card or bank card, and the bubble will disappear after full contact with the air. Then use the bank card to press the unopened tempered film and slowly press the tempered film forward, so that the lifted part can also be in contact with the mobile phone screen and glued together. Finally, gently scrape the phone screen with a bank card to make it look neat and comfortable.

2. A hair dryer.

The bubbles in the toughened film of the mobile phone not only affect the vision, but also greatly reduce the sense of experience. If there are bubbles in the toughened film of the mobile phone and there are a lot of bubbles, you can consider removing them with a hair dryer.

First, turn on the power of the hair dryer, turn on the hot air shield and blow on the phone screen, and turn off the hair dryer immediately after the screen softens. Then press the bubbles in the tempered film with your fingers, and the bubbles will disappear after pressing for a while. Note that when using the hair dryer, be sure to control the action time to prevent hot air from damaging the screen.

3. Lubricating fluid.

Facing the recurring bubbles on the edge of the phone. The bubbles disappear after pressing, but after a while the bubbles resurface in the same place, at this time you can borrow a little lubricant to eliminate the recurrent bubbles.

Start by dipping a toothpick into a little lubricant and then lift the corner close to the bubble so that the lubricant on the toothpick comes into direct contact with the bubble. When the lubricating fluid comes into contact with the bubbles, the stubborn bubbles disappear. This method is a bit cumbersome to operate, as it solves the bubbles while preventing the creation of new bubbles.

4. a clip. In the face of the bubbles in the tempered film, the simplest and roughest way is to use a clip to clamp the phone to temper the bubbles in the film. The next morning, you'll find that the bubbles are all gone.

Extended Information: Precautions for Mobile Phone Film:

1. If you buy a non-customized film, you need to prepare scissors, rulers, pens, and non-woven fabrics, and cut the film and equipment on a flat desktop to fit your own device screen. Cutting should be fast, accurate, and a success, so that it is beautiful.

2. If you buy the original film that matches your own equipment model, you don't need to cut it separately, but you should choose a good room for filming, the light should be good, and the room should be clean and free of dust.

3. The film is a delicate job, you have to wash your hands well, and dry the water on your hands to keep your hands clean and dry.

4. Clean the screen thoroughly before applying the film, especially not to leave dust.

5. After the release film is torn off, special attention should be paid to the fingers not touching the adsorption layer, otherwise the effect of the film will be affected.

6. In the process of sticking the film, do not tear the release film at one time, and should tear it off while pasting it.

7. Make good use of scratch cards for bubble drainage.

8. Carefully remove the air to avoid leaving bubbles and affecting the appearance.

1. Use a cloth (or a soft fiber cloth or glasses cloth) to wipe the screen and clean the phone screen thoroughly. It is best to wipe the screen in a windless, clean environment indoors to reduce the impact of dust on the film.

2. Take the protective film out of the package, don't tear off the release film first, and put it directly on the mobile phone screen.

3. Tear off a part of the release film, observe the label on the protective film, tear off a part of the release film marked with "", and pay attention to avoid fingers touching the adsorption layer of the protective film. Each protective film product is divided into three layers, of which and are release films, which are used to protect the protective film in the middle.

4. Slowly paste the protective film to the mobile phone screen, align the adsorption layer of the protective film with the corner of the screen, be sure to make sure the position is aligned, and then paste it carefully. While pasting, tear off the release film, if the film process produces bubbles, you can pull back the film and re-apply. After confirming that the film position is completely correct, tear off the release film completely.

After the whole protective film is attached to the screen, if you find that there are still bubbles, you can use the bank card to scrape the screen to expel the air.

5. Finally, the release film is completely torn apart.