What does Intel 45nm Pentium Dual Core Processor E6300 Boxed CPU mean

Hello, the box is with a fan. Bulk is just one CPU

Generally, you buy a radiator by yourself. Intel's CPU E6300 is good.

Dear users, the boxed processor comes with a fan. Whereas, bulk processors only have one CPU. Now it's better to buy your own radiator. The built-in fan is not very good.

Hope it helps.

Intel's CPU E6300 is good.

In terms of performance, the main frequency is a little lower than that of the E7400. Everything else is exactly the same. **Quite a bit cheaper.

Hello, 45nm is 45nm and 65nm refers to the linewidth level in the CPU process.

The definition of line width is the width of the circuit in the CPU core integrated circuit, from the early to the later 65nm (1um = 1000nm) and 45nm processes, compared to the diameter of a human hair of 40um, it is already a very fine level. In the production of semiconductors, it is achieved through the process of litography.

There are two kinds of E6300, and you can sit in the right number:

Core 2 e6300--- the first batch of Core 2 processors on the market, dual-core, 65nm process, main frequency, 1066MHz front-side bus, 2M L2 cache, 945 and above core motherboards can be supported. The performance at the default clock speed is roughly equivalent to that of the AMD AthlonX2 4600+, and the overclocking limit is about 3GHz---.

Pentium E6300--- is also the Core 2 architecture, which came out two years later than the former, dual core, 45nm process, main frequency, 1066MHz front-side bus, 2M L2 cache, almost all 945 motherboards can not be perfectly supported (either they can't light up, or they can light up but the frequency doubling coefficient can only be 6), at least G31 or above motherboards can support it. The performance at the default clock speed can be PK AMD Athlon X2 6400+, and the overclocking limit is generally above 4GHz.

To sum up, the performance of the Pentium E6300 is far better than that of the Core 2 E6300. Of course, from today's point of view, their performance has long been unable to keep up with the situation, and can only be used to form a two-claw low-end host to exert residual heat.

Don't doubt that the Pentium can surpass the Core, the most ** Pentium G dual-core, which is more powerful than the first batch of Core quad-cores.

Click to enlarge to see).

1. NTEL Pentium Dual-Core E6300 Basic Parameters Manufacturer Intel, CPU Applicable Type Desktop, CPU Series Model Pentium Dual Core, CPU Description Intel Pentium Dual Core E6300, Core Type Wolfdale, Interface Type LGA 775.

2. Intel Pentium dual-core E6300 technical parameters, processor frequency, front-side bus 1066MHz, processor frequency multiplier, bus speed 266MHz.

3. The CPU supports instruction sets MMX, SSE, SSE2, SSE3, SSE3, EM64T, Intel Pentium dual-core E6300 processor cache, L1 data cache 64KB, L1 instruction cache 64KB, L2 cache capacity 2048KB, Intel Pentium dual-core E6300 physical parameters.

4. Rated voltage, working power 65W.

The performance is comparable to that of AMD Athlon™ X2 4800+ processors, both of which are low-end desktop processors with average performance, and the detailed parameters of the two are as follows:

AMD Athlon™ X2 4800+ Specs:

Applicable Type: Desktop;

CPU series: Athlon64 x2;

CPU Frequency: ;

Slot Type: Socket Am2;

Number of pins: 940pin;

Number of cores: Dual cores;

Thermal Design Power (TDP): 65.

Intel Core 2 Duo E6300 Parameters:

Applicable Type: Desktop;

CPU series: Core 2 dual-core;

CPU Frequency: ;

Slot Type: LGA 775;

Number of pins: 775pin;

Number of cores: Dual cores;

Thermal Design Power Consumption (TDP): 65W.

Categories: Computer, Networking, >> Hardware.

Problem description: Because the previous thinking was about frequency first, what level of Pentium processor is the current Core 2 e6300 equivalent to? If it is a core2 x6800, what level of Pentium can it be equivalent to?

Analysis: There is no equivalent problem, entry-level"Buckle the meat"Also p4 is good. First of all, P4 is single-core, and the problem of single-core and dual-core will not be talked about here;

Speaking of buses, although they are all dual-core, the bus of 533 used by 805, the bus of 820 is 800, and the buckle meat is 1066;

Second, the L1 cache, 6300 is 64K, P4 has 16K, some have 32K, and PD has 32K (but L1 cache is not very meaningful);

Level 2 cache again, 6300 is 2M dual-channel, 6800 is 4M dual-channel, P4 is 1M (some are 512K), 6300 and PD are 2M dual-channel (some are 4M dual-channel, 930, 945);

Let's talk about the process"Buckle the meat"It's all new technology, it's all 65 nm, P4 is all 90 nm [some are still 130 nm old guys (don't like to listen to 130 nm, sorry)], pd part is 90 nm (805, 820, 830), part is 65 nm (915 or more), the smaller the value, the smaller the power, and the heat dissipation is easy to solve. And then there's the core inner type.,Each generation of CPU has a special inner type.,It's only getting better and better (I only know Seyan and the old Pentium).

And then there's overclocking"Buckle the meat"The external frequency is high and the frequency is low, and the process is 65 nanometers, so there is nothing to say about it; The previous processor had a high frequency, which was the reason for the high frequency doubling, and it was difficult to surpass. A simple example: e6300 has an external frequency of 266, and the frequency of doubling is 7 times; P4561 has a frequency of 200 and a frequency of 18 times.

I must say that if it is equivalent (I don't agree with this word), then there is only one effort on the main frequency, which is the dual-core PD945 with high main frequency

This talent is shallow, and there is a hope for better opinions to exchange.

1: Intel (Intel) 32nm Pentium dual-core processor G620 E6500, this is equipped with a first-line main motherboard, I recommend you to use this frequency, not expensive more than 400 points, economical.

2: Intel 32nm Pentium dual-core processor G840

3: AMD Phenom II 2 (Phenom II Dual-Core) 555, it is good to be able to open the core.

4: AMD Athlons II X2 (Athlon™ II Duo) 255 AMD Athlons II

Look at the following I will explain to you: I can only say that AMD is usually more cost-effective under the same **. But judging from the overall performance of the CPU, if it is the same core, Intel must be much stronger.

Therefore, Intel dominates the mid-to-high-end market, so AMD in the mid-to-high-end market can only compete by one or two more cores than Intel. This situation also extends to the low-to-mid market. AMD400 provides three cores, and 600 yuan provides four cores to compete with buckle meat or i3 processors.

In the low-end market, because Intel cannot reduce high-performance products to the low-end market, the performance of AMD in the low-end market is not much different from that of Intel. However, due to the overall platform type is more cost-effective, AMD still achieved good sales performance when the processor performance is not as good as Intel's.

Before AMD's new architecture bulldozer came out, AMD was the only advantage that AMD had and could use to deal with Intel.

Most of the people who buy AMD because they are cheaper, and the overall platform** is relatively low, and at the same time provides a good experience.

In terms of single-core performance, AMD still has a big gap with Intel, and AMD's smart thing is to deal with Intel's dual-core through multi-core. And multi-core does have a great advantage in multi-tasking and multi-open games. The mid-to-high-end uses six cores to cope with the i7 quad-core.

In addition, its smooth upgradeability and relatively good integrated graphics card performance have also made many low-end users switch to AMD.

Therefore, AMD should be the first choice for low-end platforms, and Intel is the only choice for high-end platforms. In the mid-to-high-end market, Intel also has the advantage. The low-end market is AMD's world.

If you don't know much about computers, you can buy a brand machine, and it's not much expensive. And it's not easy to be fooled, and it also comes with a genuine system.

If you buy a brand computer, you can look at the manufacturing technology, you won't buy the old product, 32 nm must be better than 45 nm.

Intel's is generally a bit more stable than AMD's.

AMD Phenom II 2 (Phenom II Dual-Core) 555 is the best if it can open the core, JD.com sells 589RMB

But I suggest you add more than 200 pieces on the i3 2100 cool a lot.。。。 795

Intel 32nm Pentium dual-core processor G620 boxed better.

1. NTEL Pentium Dual-Core E6300 Basic Parameters Manufacturer Intel, CPU Applicable Type Desktop, CPU Series Model Pentium Dual Core, CPU Description Intel Pentium Dual Core E6300, Core Type Wolfdale, Interface Type LGA 775.

2. Intel Pentium dual-core E6300 technical parameters, processor frequency, front-side bus 1066MHz, processor frequency multiplier, bus speed 266MHz.

3. The CPU supports instruction sets MMX, SSE, SSE2, SSE3, SSE3, EM64T, Intel Pentium dual-core E6300 processor cache, L1 data cache 64KB, L1 instruction cache 64KB, L2 cache capacity 2048KB, Intel Pentium dual-core E6300 physical parameters.

4. Rated voltage, working power 65W.

Although I would love to list them, they have all been discontinued, and there are too many influencing factors in the second-hand market, so I can't tell you everything directly, I can only roughly estimate it, about 2500

Are you selling, or buying?

Sell: 1200-1800

Buy: 2000

Buy this configuration, do you have more money, or is it not enough money to match better?