How about the BMW 3 Series maintenance light is reset to zero?

This requires a dedicated instrument reset, or a manual reset. Autel MS908 supports one-key maintenance lamp reset.

The operation method is shown in the following figure:1. When the car reaches the maintenance cycle, the oil change indicator light on the car dashboard will light up, which needs to be manually eliminated.

2. Connect the external control computer of the car to the on-board computer, and select the engine option.

3. After that, select the matching function and enter the function module.

4. After that, it will prompt that the control module accepts the request and will update the read data.

5. After that, the pop-up interface selects the maximum time value for maintenance. Modify the stored data to new data so that the service interval is not further prompted.

6. After clicking OK to modify the new data, there will be no maintenance prompt.

After the maintenance is completed, it must be reset and can be reset to zero. I use GT oil to maintain it myself, and after maintenance, I manually reset it to zero, which is very simple. This engine oil is a base oil of Class IV PAO, with good anti-recession ability, and the maintenance mileage can be increased from 10,000 kilometers to 15,000 kilometers, the power increase is very good, and the cleaning and quietness are good.

Maintenance manuals or online are available, and more importantly, the maintenance lights are actually to remind you that it's time for the car to be maintained. So in fact, many times, because we use better engine oil, so the maintenance time will be much farther than the manufacturer's preset mileage, I use G T Magic Red engine oil, use it once to offset the original engine oil two or three times.

BMW 3 Series Maintenance Lamp Zeroing Method.

Insert the ignition key, press the "start stop" button on the left side of the ignition key holder), press the zero button on the upper left side of the meter, and release it after about 15 seconds, at this time, the LCD screen in the upper left area of the meter will be displayed as follows:

return.

8mths brake fluid.

30tkm engine oil 30,000 km.

40tkm front brake pads 40,000 km.

40tkm rear brake pads 40,000 km.

50tkm body inspection 50,000 km.

microfil 60tkm

Spkplugs 60tkm Spark Plug 60,000 km Coolant 32mths coolant (Note: When the specified kilometers or dates are exceeded, the LCD** display area will display maintenance information, and when the meter is reset to zero, the main menu will display "!"). "Reminder word.

If the front brake pad is replaced for more than or not zeroed, it will display "40tkm!".”

Manual zeroing. The specific BAI operations are as follows:

1 Ignition switch duoff

2 Press the journey button A (in the lower left corner of the ZHI speedometer)3 Turn the ignition key to position 1. dao

4 Press and hold button A for 5s until you find the words "oil service" or "inspection" and "reset".

5 Release button a. Press the journey button again and hold it for 5s until "reset" starts flashing.

6 Release button A, then press and hold button A.

7 New service intervals will be displayed.

8 Press button A again and the word "end sia" appears, and the ignition switch is off.

Give it a try!

The BMW 3 Series maintenance lamp zeroing reset method is as follows:1. The ignition is turned off.

2.Start by pressing the trip button A (in the bottom left corner of the speedometer). 3.

Turn the ignition key to position and hold the button for 5s until the words oil suit or check and reset appear. 5.Release button A

Press the trip button again and hold for 5s until "reset" starts flashing. 6.Release the button Xiangyuan A, and then press and hold the button.

The new maintenance interval is displayed. 8.Press button A again, the words "End SIA" appear, and the ignition is turned off.

BMW 3 Series maintenance precautions: always pay attention to clean the filter of the car. Don't underestimate it, it directly affects your car's fuel consumption.

During the use of the internal combustion engine of the car, impurities such as dust will continue to mix into the engine oil. At the same time, the air body and combustion exhaust gas will oxidize the engine oil, so that the oil will gradually produce gum or sludge, which will not only accelerate the wear of parts, but also easily cause oil blockage. Therefore, clean your car filter regularly until you replace it with a new air filter.

Maintenance: On the one hand, maintenance services can minimize maintenance costs; On the other hand, the restored car can ensure safe, stable, and economical driving. In addition, faults can be detected as early as possible and hidden dangers can be eliminated.

What's more, regular maintenance at Shanghai Volkswagen dealerships in accordance with the maintenance cycle is a prerequisite for quality assurance services. Maintenance includes: every 15,000 km.

Change the brake fluid. The brake fluid is changed every two years or every 50,000 km, whichever comes first in time and mileage.

Millions of car purchase subsidies.

1. To manually reset the maintenance light of the BMW new 3 Series to zero, you need to press the button in the lower left corner of the dashboard of the BMW new 3 Series vehicle as shown in the figure below.

2. Then continue to press and hold the button in the lower left corner of the dashboard of the new BMW 3 Series vehicle, and then press the start button of the vehicle to start the vehicle.

3. After the BMW new 3 Series vehicle starts, you need to continue to press and hold the button in the lower left corner of the BMW new 3 Series dashboard for five seconds before it will rot.