What should I do if my phone is soaked in water, what should I do if my phone is soaked in water

I have the most say in this, all my mobile phones have been in the water, whether it is a high-end machine or a cottage Needless to say, find a place to take a break They just put it in the magnetic shock machine to get it, that is, about 20 yuan, if it is not repaired, forget it If the clamshell machine is repaired, it is recommended to sell it because the cable is very easy to break After it is broken, it will not be durable to replace it High-end smart phones will quickly take the customer service to repair Because the small traders and vendors below are all messing around, and the customer service cannot be repaired Believe me, the most important thing is that the pure water is good Don't soak it in laundry detergent water It will definitely corrode the motherboard Then hurry up to customer service to repair it It's not much expensive Don't worry about it It's best not to do it yourself You can't have enough food and clothing.

Unplug the power. Dry your phone as fast as you can, including the inside. Or tumble dry. If you are not completely sure, put it in a ventilated place for 2-3 days. Put on the battery and try it out. If it doesn't work, you can only send it for repair.

It should be fine, my mobile phone Samsung U708E, I forgot to take it out of my pocket last Sunday to wash my clothes, and I washed it in the washing machine for 23 minutes, took it out, removed the battery, dried it with a paper towel, and then blew it with a hair dryer, and went to see the new phone. I came back and put on the battery and tried it, but it turned on.,It's a big watermark on the screen.,You can also receive text messages and call**。 I suddenly felt that Samsung was too powerful, but the wet battery drained quickly and heated, so I replaced a battery, and the manual said that the battery was easy to soak in water, so don't use it.

Before going to bed, I removed all the detachable and put it on the power adapter of the notebook (it was very hot after use), and put an activated carbon desiccant on it, and the watermark was a little less the next day. After that, I did this every day before going to bed for two days now, and the watermark is almost gone.

Immediately take out the electric board, blow it with a hair dryer, and then put it in the sun to dry, I have one that is handled like this, and it can be used.

Take it out immediately, open the back cover, peel off the battery, and then wipe it vigorously with a piece to wipe the water clean, otherwise, you will have to take it for repair.

Immediately take the battery out, wrap it in absorbent paper, take it to the mobile phone to repair it, and coax it dry, and disassemble it yourself.

1. Take the battery off as quickly as possible.

2. Disassemble the machine and blow it with a hair dryer.

3. Do not turn on the machine when there is still water inside.

Remove the lid, remove the battery, blow it dry, and if that doesn't work, take it and fix it.

Take it apart and blow it down with a hair dryer. Be quick.

Wash the water out with a sponge, or buy a new one.

Disassemble and dry... If you really can't do it, go to a repair shop.

You take the phone apart, preferably quickly, and then dry it again. ok!

Dry the pool immediately with an electric breeze.

Hair dryer blows day after day and then day.

Take it out and dry it. If it doesn't work, change it.

Try this method after the phone is soaked in water:First, take out the phone that accidentally fell into the water and use a paper towel to absorb the surface moisture.

It is recommended to use a hair dryer to blow continuously for more than 15 minutes, and it is best to leave the phone for more than 5 hours after drying it before trying to turn it on.

Disadvantages: Due to the different water ingress parts, this method is risky and may cause damage to the mobile phone motherboard, so be cautious.

Precautions: Do not use the hot air function of the hair dryer, the conductivity of the water meets the high temperature of the hot air, which may cause the battery interface to leak or the internal circuit to short-circuit and burn the phone.

The first step is salvage:

Whether the mobile phone is dropped in the basin, the toilet, the lake or the river, or in the rain, the first step is not to be in a daze, and let the water machine get out of the water source as soon as possible. Because the longer it is in the water, the greater the damage to the mobile phone, such as the motherboard, screen, battery, buttons, etc., just like a person drowning, the sooner you are rescued, the greater the probability of survival;

Step 2: Wipe dry:

After scooping it out of the water, immediately wipe the surface of the phone dry with a dry paper towel, rag or even clothes, take out the SIM card slot, and use a paper towel to absorb water at each opening of the phone. Remember, don't press the power button and volume button, don't turn on, don't turn on, don't turn on, don't turn on, this is the most important point, because once turned on, due to the water in the fuselage, connecting the power again will cause the motherboard to burn out;

Step 3 Drying:

Use a hair dryer to turn on hot and cold air alternately, aiming at the openings of the mobile phone, such as charging ports, headphone jacks, SIM card slots, etc., if it is soaked in water, you need to blow for a while, if it is only partially watered or partially watered, you do not need to blow for too long. Then you can put the phone in a pile of rice or desiccant, and you can take it out after a few hours;

Step 4Try to boot:

After the above steps, you can try to turn on the computer, if it can turn on normally, don't be happy too soon. Check whether the buttons, fingerprint recognition, screen touch, and speaker of the mobile phone are normal;

Step 5: After-sales maintenance:

After the first four steps are invalid, send them to the after-sales service. Ask if you can repair and repair**, and if you can repair and **acceptable, you will repair it.

The mobile phone has been soaked in water for a long time, and it is basically scrapped, and there is no point in repairing it, so you can go to the after-sales maintenance there to test it.

If you are using a vivo phone, you can check the following mobile phone liquid inlet treatment methods:

1. Shut down immediately and take out the SIM card and SD card; Do not force it on, it is very likely to cause a short circuit.

2. Lay the fuselage flat, use a paper towel or soft cloth to absorb water, and try to absorb the water in the gaps; Try not to move your phone when absorbing water.

3. Do not attempt to charge; Don't shake your phone too hard; Do not heat your phone.

4. Stand in a ventilated and dry place, and place it with the screen and potato curtain facing upwards and the head of the front cameraman tilting upwards;

1 Water ingress and crashing are the two major taboos in the use of mobile phones, and water ingress of mobile phones is particularly serious. According to an engineer from Guoxin, after the mobile phone gets into the water, the first thing to do is to turn off the power, of course, not to press the shutdown button, but to remove the battery. Because as soon as you press the shutdown button, the mobile phone will be powered on, and it is likely that a short circuit will occur, causing damage to the sock mobile phone, and then send it for repair as soon as possible.

If your phone's warranty has expired and you don't want to send it for repair, you can boldly take it apart! Wipe the parts of the phone with a tissue, and then blow it with a hair dryer for a few minutes, in order to ensure that all the internal parts are dry, it is advisable to air dry the phone for a few more days before you can turn it on again. 2 Once the mobile phone gets into the water, you should immediately remove the power Zheng Bian, and do not turn it on immediately to understand the condition of the mobile phone.

After removing the battery, do not use a hair dryer to deal with it, and immediately send it to the repair professional to disassemble the machine for water treatment, such as falling into sewage or corrosive liquid, and use ultrasonic cleaning and drying before proceeding to the next step of maintenance. If the mobile phone can still be used after water penetration, it should be sent to a professional to deal with it to avoid corrosion of the circuit board and make it impossible to repair. 3 No matter what kind of water the mobile phone falls into, you should first remove the residual pool of the mobile phone and no longer power the mobile phone.

If it falls into clean water, remove the battery and clean the phone with anhydrous alcohol, because the alcohol volatilizes quickly, and the water on the circuit board can be volatilized together. Then use a heat gun or hair dryer to dry the circuit board, and then power up the test machine, and most mobile phones will work normally. If it falls into the sewage, it should be cleaned immediately, and the dirt that can be seen should be cleaned first.

Use a brush to brush off the impurities attached to the pins of the components. Then, the circuit board is scrubbed with an alcohol cotton ball, and if the pollution is serious, the impurities must be vibrated out with the help of an ultrasonic washing instrument. Then use an air gun to dry the circuit board, and then repair all the chips.

Immediately remove the battery, do not turn on or off, and then blow with a hair dryer, and disassemble the parts of the mobile phone as much as possible, so that the blowing effect will be better. If you can't, just take the phone store yourself, and he'll get it for you.