After the router is set up to connect, the mobile phone is connected to the signal, and the network

Set up your wireless router again.

Does the cat connect to the wireless router, do you do this:

Plug in the wireless router, don't pick up the cat first, reset the wireless router (restore to the factory), and connect the computer to any LAN port of the wireless router.

Enter the gateway address of the router (on the label on the back of the router) in the address bar of the browser, enter the settings page, and set it according to the PPPoE (ADSL virtual dialing) method.

Then set the SSID, encryption method, and .

Password. Save, restart.

After setting, connect the network cable from the cat LAN port to the WAN port of the wireless router.

Is the wire router connected to a wired router? address to the 740n settings page.

And if you still haven't solved it?

Check the IP of the wired router (check that you are not connected to the 740N, and then connect the network cable from the wired router to the WAN port of the 740N.) 1, if it is also 192, it will conflict with 740n.

In the future, if you adjust the wireless parameters, the IP and gateway when the computer uses the network cable to directly access the Internet. 1. Wireless parameters are customized.

Save after restarting. , with 192.

The solution is to connect the 740n separately to set it up first.

In the WAN port settings, select Dynamic Acquisition.

The LAN port setting is changed to 192, and the gateway is the IP of the router).

The signal display only means that the wireless signal is good, but it does not mean that the network is connected, please check the settings of the router.

The correct settings are as follows:

Assuming the IP address of the router is, refer to the label or instruction manual on the router box.

1. One end of the network cable is connected to the LAN port of the router, and the other end is connected to the network port of the computer.

2. Open the browser, enter the IP address of the router), enter the router account and password (see the label or manual on the router box).

Internet access: PPPoE

Internet ID and Internet Password: Enter the broadband account and password.

Click Next.

4. Wireless status: on.

SSID: Enter the name of the wireless device.

Channel: Select 9 (if connected to an Apple mobile device or Mac: select 11 or 13).

PSK Password: Enter the wireless password.

Other defaults are sufficient.

5. After the setting is completed, one end of the network cable is connected to the LAN port of the modem, and the other end is connected to the WAN port of the wireless router.

Here's how to set it up:

Open a browser on your phone and enter it in the address bar to enter the wireless router settings interface.

An account and password to log in to the router appear in the settings interface, enter the default account and password admin according to the setup wizard step by step settings, select the Internet mode, usually adsl users choose the first PPPoE, if you use other network service providers, select the following two according to the actual situation, if you don't know how to choose, directly select the first item to automatically select, convenient for novice operations, click next after selection;

Enter the account and password applied for from the network service provider, and go directly to the next step after entering.

Set the wifi password, try to make the alphanumeric combination more complicated, and it is not easy to be rubbed off the network.

After entering it correctly, it will prompt whether to restart the router, select Yes to confirm the restart of the router, and you can access the Internet normally after restarting the router.

The IP settings of wifi do not match, and the specific settings are as follows:

1. Tap the settings icon in your phone.

2. Then click on "WLAN" in the "General" tab.

3. At this time, you will enter the wifi page.

4. Click on the "Advanced" option below.

5. At this time, the "WLAN Advanced Settings" boundary has been entered.

6. Find the "IP address" below and turn the number after the third point of the IP address into a number similar to this number, such as changing 2 to 3.

7. Now open a Siddle browser.

8. At this time, the browser will display ** or web page, because the mobile phone can already connect to wifi at this time.

The router is connected and the phone shows that the network is not available, what should I do?

If the mobile phone cannot connect to the wireless network, please try to cope with the following situations: 1If you could connect before, you can't connect now:

Check whether other devices under the same wireless network are connected properly and whether connection restrictions are set on the wireless network. 3.If you cannot connect to the wireless network with the Chinese name, the vertical will be judged:

Due to device compatibility issues, some wireless networks with Chinese names or special staring symbols may not be able to connect, it is recommended to change the wireless network name to English. 4.If the search cannot be found, an error is reported, or a timeout occurs

Please check whether the router connection is normal (the cat cannot be connected), turn off the phone and the router and restart it before trying to connect.

There are several reasons for this.

1 The mobile phone has been set to connect to a fixed IP, but the IP is wrong, so it can't be connected.

2.There is a problem with the router settings, or the router itself does not have an external network.

3。The router is dead.

Solution: 1 Check the line of the router first, whether the WAN port has been connected, and whether the light is flashing.

First, use the computer to connect directly to the router through the network cable, and automatically get the IP to try the stool, it seems that you may not be able to connect to the external network, if not, it is not connected to the external network, or there is a problem with the external network.

"A-There is a line by. LAN port, B-wireless router. WAN port" connection settings:

First, there are lines set by the description:

A has a line set by the IP: PPPoE connection "cat", can access the Internet. The gateway segment is:

For example, if A is already occupied, the B wireless router must be replaced with another gateway segment. Such as:

Note: The network cable directly dials up the Internet, and there is no "cat". As long as you have access to the Internet, you can proceed to the following steps!

Second, let's start setting up wireless routing:

Don't connect the network cable from A to B, but use a computer and network cable, first connect to the LAN port of B, and set it in (enter it in the IE browser first:

Click Open. Other brands are operated according to the back of the router or in the manual, such as: ).

1.Go to the wireless router settings page and click to open the :

Wireless routers.

2.(After saving, the wireless router settings page can't be opened), at this time, enter in the IE browser: , click to open, and enter the settings.

Page 3Click to open the left side: In the "WAN port settings", set the acquisition method as: "WAN port connection type" and select "Static IP", (

Like I have a line by yes, IP address, subnet mask, default gateway, preferred DNS server.

Fill in all the alternative DNS services ("Wireless Router Connection" to the IP address of "Wired By"). Click.

Save", if you need to restart the wireless router. Be careful not to conflict with the IP addresses of other computers in the A router.

4.After confirming that B's wireless function is turned on (you can check and click on the "Wireless Settings" item), connect the network cable connected from A to B's WAN port and turn it on".

Write "The IP set in the WAN port, the specific is the same as the one written above", click Next after filling in, set the wireless network password, and click Next when finished.

Click "Done".

PC MAC Address", click "Clone MAC Address" at the back, and click Save.

6.Click to open the left: Click "DHCP Server" in the drop-down project to see that there is a "gateway" in the interface.

The main DNS server "fill in the I'm filling in this" and click "Save". Close the wireless router page.

7.The setup was successful. You can choose to automatically get an IP address on your computer to test it, connect it to your laptop, or turn on the wireless connection.

Select a DNS server, and you don't need to fill in the optional DNS server. But it's best to opt for getting the IP address automatically.

Is it not always connected, and the password is 100% correct. Log in to the wireless router - wireless settings - basic settings, change the SSID to a new one, restart the router, it's OK, I've just done it.

There is a wireless setting in the router - advanced wireless settings - wmm This option can be canceled to use defy to surf the Internet.

Automatic dialing can be set up in the wireless router, and if the dialing is successful, the mobile phone can access the Internet.

To enter the correct network key.

Mine is the same way, can you get it right? Teach me.

The laptop is connected to the router to access the Internet wirelessly, but if you want to dial a number, do you need to dial up?

1) The wifi is not connected to the external network, and the network is not connected normally.

2) Abnormal failure of wifi equipment. You can restart or replace your device.

3) Service interruption of the operator (such as the problem of China Telecom, China Mobile, and China Unicom's optical cables) 4) The network cannot be accessed due to the arrears of broadband payments.

You may not have broadband access to your router. Because the router can be connected to the signal as long as it is turned on and not connected to the cat, but it cannot be connected to the network. You'll need to write your broadband username and password into your browser to connect.

For the specific connection method, you can take a look at the manual of your router. It's pretty easy to set up.

Here's how:

1.Turn the cat off first.

2.Then unplug the connection between the cat and the router.

3.Okay, now there's only the route left.,Enter.,It depends on the situation and there are also 4.Factory reset, in the last row, System Tools that.

5.On the second line, the setup wizard re-enters the password account number, and oh that's it!

6.Reboot the router.

7.Connect the wires between the cats, power the cats, and connect to the network!

8.A miracle is coming!