How to set up Telecom Huawei Cat? How to set up the telecom optical modem

1. First of all, you need to enter the modem page in the address bar of the browser.

2. Then on the new interface, click on the Network tab and switch to the WLAN settings page.

3. Finally, set according to the parameters in the figure, country, wireless mode, main channel, rate, sending power, and finally click enable to complete the setting.

If you forget the login password, you can restore the factory settings through the Reste button, then check the default login address and login account password at the bottom of the modem, enter the modem management interface, and then reset the broadband connection.

Tools: Computer; light cats;

The steps are as follows:

1. Press and hold the reset button, wait for all the indicators of the modem to go out at the same time, and let go, at this time, the modem will restore the factory settings successfully;

2. Check the default account password and login address at the bottom of the modem;

3. Enter the background management address of the modem in the browser;

4. Enter the administrator password to enter the modem management page.

5. Click "Route Settings";

6. Select "Internet Settings";

7. Select "broadband dial-up Internet access" for Internet access;

8. Then enter the broadband password, the IP address and DNS server do not need to be filled, and will be automatically obtained by the modem;

9. Click to connect, after the connection is successful, you can turn on the computer in the future and access the Internet without dialing.

1.First, open the browser, enter, press Enter, and enter the following interface.

2.Then enter the username and password on this interface - please check the username and password on the back of the modem for the first time, and finally enter the following interface.

3.On this screen, select Network - WLAN Configuration, and on this page, you can set the wireless network parameters, including wireless network switches, SSID configurations, and channel options.

4.Note that at the top of this page, there is an open Wi-Fi area, and put a checkmark in the box in front of it.

5.Then enter the required SSID name (that is, the name of the wireless WiFi) in the SSID detailed configuration information interface, and tick the box behind the connection activation - to ensure that it can be enabled after the setting is completed. Among them, the number of device connections is to call this wireless wifi can have several device links, which can be set by yourself.

Also put a checkmark on the box behind the broadcast SSID - to ensure that you can search for this SSID; As for the encryption method, you can default or choose a more reliable way by yourself, and then enter your own face and click Apply.

6.You can set the relevant parameters in the advanced settings, and the following will be interpreted one by one: transmission power - that is, signal strength, channel - with wireless signal as the data signal transmission channel (this default can be).

Now the cats given by Telecom do not have a routing function, I can set up an automatic dialing 50752591 for you

Telecom's Huawei brand cat is not set by the user himself, after installing the line, directly connect to the computer to dial up the Internet and use.

The telecommunication cat is a device for signal conversion between the computer and the first line, which is composed of two parts: the modulator and the demodulator, the modulator is the digital signal of the computer (such as files, etc.) is modulated into the sound signal that can be transmitted on the first line, and at the receiving end, the demodulator converts the sound signal into a digital signal that the computer can receive. Data communication between computers can be realized through a modem and a ** line.

Here's how to set it up:

Operating Equipment: Dell Inspiron 7400

Operating system: win10

Procedure: InternetExplorer

1. Log in to Unicom modem: Open InternetExplorer on the desktop, enter enter, and enter the routing login interface.

2. After logging in, various setting options will appear.

3. Check each setting item: In the status, you can see whether the Unicom network you are connected to now is registered, and you can surf the Internet normally.

4. Internet settings: Enter the Internet access and password here.

5. Optical modem router wireless name setting: SSID name, here is the wireless name used, change it to your favorite name.

6. Optical modem router wireless password setting: WPA pre-shared key, set wireless Internet password.

7. Login Unicom optical modem password setting: The user name cannot be modified, and the password can be changed to be familiar to you for the next login.

1. Unplug the optical fiber and turn off the power.

2. Press and hold the reset button and then turn on the power, and then release the reset button after about 10 seconds when the red light changes from solid to flashing.

3. Wait for one minute before turning off the power and then turning it on.

4. Optical modems generally do not have wireless, you have to buy one more wireless router, and you also need to buy another network cable. Connect the LAN port of the fiber modem to the WAN port of the router with a network cable, and connect the LAN port of the router to the computer with a new network cable.

5. Then enter the router settings, use the wizard mode, select the PPPOE type according to the prompts, fill in the broadband account number and password, and then set a password for the wireless.

I don't know if the students who have optical cats at home have encountered this kind of problem, that is, when the telecom is upgraded to optical fiber, the optical modem often has a little problem, at this time, you need to set up the optical modem, and if you can't set it, you can take a look at the following content.

Turn on step-by-step reading mode. How it works:

Connect the device as shown below.

Enter telecomadmin in the browser, and the default superusername and password are telecomadmin.

When logged in as a superusername, you can query, configure and modify all settings. Start by configuring the broadband connection,Configure it as shown in the figure below (pay attention to the port binding part,2 is not checked,Because it is used to put IPTV),vlanid with your own value,After the configuration,The light modem can automatically dial up the Internet。

Wireless configuration, select the wireless switch to turn on, and the others remain unchanged.

I set a wireless password.

Configure IPTV,The main thing is the VLAN value,There is also port 2 and SSID2 are bound here,Try not to move it,A few steps through the wireless stupid sail,Wireless is ready,Terminals that can access the Internet wirelessly at home are all to WIFI Internet surfing。

Finally, the basic configuration of broadband**,The username and password are also the only identifiers of your home**number,Once changed,**It won't work,This is also a place for verification,If you change,The light modem will not pass。