Why can t the laptop get up after the system is finished black screen is full of foreign language ma

This is not like a system problem, this is generally a hardware problem, and the problem with the graphics card or screen may be larger. If you are sure that hibernation standby and other possibilities are ruled out. This graphics chip is probably the biggest problem.

Please replace your system,I have a very good win7,My notebook has been installed many times in 12 years and is not very easy to use,I also changed the solid state drive,It's not good to make,I stumbled upon this win7,Really smooth,Can be given to you。

There are several reasons why the monitor screen is black after the laptop is reinstalled on the system:

1. There are missing files in the system. Causes the installation to fail.

2. Hard disk failure, such as bad sectors, causes failure.

3. The boot record of the hard disk is damaged, and it cannot be started without the boot record after installing the system.

Based on these three reasons, the following measures need to be taken.

1. You need to check and repair the hard disk, rewrite the boot record and reinstall the system.

2. Detect the bad sectors, format the hard disk and reinstall the system.

3. If the file is simply missing, you need to reinstall the system with a different version.

Graphics card issues!

When installing the system, don't install the graphics card and motherboard chip driver, and then use the driver wizard or driver life update when you finish installing! Just look at whether the heat of your laptop is very high, if so, turn off the computer, wait for 10-30 minutes before using it, and see if it can be solved!

Enter the safe mode to see if it is feasible, that is, it can be opened normally If it can, you can reinstall the lower driver.

Find another computer to download your driver, copy it and install it.

If it doesn't work, change the system version and redo the system disk and install it again.

Again, completely, remove the hard drive and reinstall it.

Try a different system, the computer memory is 2G with 32 bits. 4G 64 bits, here under the new radish home I use, easy to use.

Driver issues. It is recommended to press F8 to enter the safe mode when booting up, delete the display driver, and then re-enter to see. In addition, the system of cloning disks will be more or less problematic.

After powering on, press F1 to set it.

There are two reasons, this is because your motherboard has no battery, or your motherboard's BIOS is out of order, causing your motherboard's boot item to become a floppy drive, not an optical drive or a hard disk, and there is a motherboard self-test to the floppy drive, so you have to press F1 to continue.

1. Change a motherboard battery.

2. If the previous step has no effect, the solution is as follows:

Press F2 or Del (there is a prompt on the screen, follow the on-screen prompt) to enter the BIOS settings.

1. Set the BIOS to factory default.

Boot press Del to enter BIOS settings - in the main BIOS interface, select "Exit" with the keyboard arrow keys, and select "Load Setup DeGauits" with the keyboard arrow keys in the Exit interface - press F10 - select "OK" - press Enter - save to exit BIOS settings.

2. Turn off the floppy drive. Boot press Del to enter BIOS settings - in the main interface of BIOS, use the keyboard arrow keys to select "Main" - in the main interface, use the keyboard arrow keys to select "Legacy Diskette A", make it inverted - press Enter - enter the "Options" dialog box - use the keyboard arrow keys to select "disabled" - Enter.

3. Set an error message prompt.

In the BIOS main interface, use the keyboard arrow keys to select "Boot" - use the keyboard arrow keys in the Boot interface to select "Boot Settings Configuration" to make it inverted - press Enter - enter the "BootSettings Configuration" interface - use the keyboard arrow keys to select "Wait for 'F1'lf error" to make it inverted white - press Enter - enter the "Options" dialog box - use the keyboard arrow keys to select " disabled" - Enter.

Hope it helps.

cmos setting wrong

The CMOS is set incorrectly, and the time is set incorrectly.

Press the delete key when turning on the computer, enter the CMOS menu to modify the settings, and change the time to the current time.

To this page, press f1 first, if you can't, it should be a system crash, and reinstalling it should be solved.

It should be a system problem, or it may be poisoned, and it can be solved by doing a system.

Just reinstall the system with a verified system disk, so that the system installation problem can be solved automatically and smoothly throughout the process. These are possible with a USB flash drive or hard disk, and the installation speed is very fast. But the key is:

It is necessary to have a system disk that is compatible with IDE, ACHI, and RAID mode installation and can be automatically and permanently activated, and can automatically install the machine hardware driver sequence, so that the system can be automatically and smoothly reinstalled throughout the process. Here's how:

3. **version tutorial: How to give you the detailed **version installation tutorial in this regard? Can't be attached. will be judged by the system as a violation.