What are the safety operating procedures for internal combustion forklifts

The obvious copy of the upstairs contempt! Experience is everything!

The safety operation procedures and safety precautions of forklifts are as follows:

1. You must check before leaving the car.

2. When there is someone in front of you while driving, you should send a signal 5 m away.

3. The driving speed in the factory shall not exceed 15 km h, and the speed shall not exceed 10 km h in other complex areas such as factory gates, elevators, turns, crowded people, narrow passages, etc.

4. The low point of the goods from the ground should be in m.

5. The turning should not be too fast to prevent the tendency of "free turning".

6. The uphill and downhill slopes should run slowly and at an even speed, and no turns on the ramp.

7. Do not drive across the slope, when the slope is greater than 10%, the downhill should be reversed.

8. When the forklift personnel carry the goods forward, if they encounter large or bulky goods to be the driver's sight, they should take the reverse drive.

The safety operation procedures for forklift operations are as follows:

1. Before starting, you should observe the situation around the forklift, fasten the seat belt, and start after confirming the safety.

2. When the forklift is driving, the height of the bottom end of the fork from the ground should be kept at 300-400 mm, and the mast must be tilted back.

3. When the forklift is running, no one is allowed to get on or off the car, and it is strictly forbidden to stand on the fork legs. The body should be kept inside the forklift and never extend any part of the body into the running track of the mast.

4. When the forklift is driving, the fork shall not be raised too high, and when entering and exiting the cold storage operation or driving, it is necessary to pay attention to the air, and it is forbidden to brake sharply and turn sharply.

5. When the forklift is working, the lifting and landing must be stable, and overloading is strictly prohibited. It is forbidden to suspend the goods in the air after the forklift is stopped, and the lifting frame should be lowered before driving after unloading.

6. When forklifting goods, the weight of the goods should be evenly shared on the two forks, the goods should not be deviated, and one side of the goods should be attached to the shelf. The items carried by the forklift must not be too high to obscure the driver's vision.

7. When the forklift approaches or evacuates the items, the speed should be slow and steady, pay attention to the wheels not to crush the items, and the fork head should not be sleepy and scratch the items and the staff.

The safety regulations for forklift operation are as follows:

The forklift safety operation procedures are the operating procedures formulated to ensure the safe, accurate, standardized and effective operation of forklift trucks by forklift drivers. The regulations stipulate the operation specifications of forklift drivers in all aspects of starting, driving, loading and unloading.

Purpose: To standardize the safe operation and safe driving of forklifts; Scope of application: forklift driver; Forklift Truck Safety Driving Rules:

1.You must pass the examination of the relevant departments and obtain the special type of operation certificate issued by the ** organization before you can drive the forklift, and strictly abide by the following safety operation procedures.

2.It is necessary to carefully study and strictly abide by the operating procedures, and be familiar with the performance of the vehicle and the road conditions in the operating area. Master the basic knowledge and skills of forklift maintenance, and conscientiously do a good job in the maintenance of vehicles according to regulations.

3.It is strictly forbidden to drive with people, and it is strictly forbidden to drive under the influence of alcohol; Eating, drinking, and gossiping are not allowed during the drive; Mobile phone calls are not allowed while driving.

4.Before the vehicle is used, it should be strictly inspected, and it is strictly forbidden to go out of the car with faults, and it is not allowed to force through dangerous or potentially dangerous road sections.

The operation of the driver of the electric forklift must comply with the requirements of the safety regulations.

1.Before operation, check the effectiveness of the brake system and whether the battery power is sufficient, and if any defects are found, they should be treated and improved before operation.

2.When handling goods, it is not allowed to use a single fork to run the goods, nor is it allowed to use the tip of the fork to provoke the goods, and all the forks must be inserted under the goods and the goods are evenly placed on the forks.

3.Start smoothly, be sure to slow down before steering, don't drive too fast at normal speed, and brake and stop smoothly. It is not allowed to stand on the fork, and it is not allowed to carry people on the forklift.

4.For larger goods, be careful to handle and do not carry unsecured or loose goods. Check the electrolyte regularly, and it is forbidden to use open flame lighting to check the battery electrolyte.

5.Before parking, lower the fork to the ground and place the forklift neatly, stop and disconnect the vehicle.

6.When the power supply is insufficient, the power protection device of the forklift will be automatically turned on, and the forklift fork will refuse to rise and prohibit the continued use of goods.

7.When charging, first disconnect the forklift working system from the battery, then connect the battery with the charger, then connect the charger with the power socket, and turn on the charger.

8.Under normal circumstances, the intelligent charger does not need manual intervention, and the output voltage and current value of the charger can be manually intervened without intelligent charger, usually the voltage output value is 10% higher than the nominal voltage of the battery, and the output current should be set to about 1 10 of the rated capacity of the battery. (For example, DC24V 210AH battery, the output voltage and current of the charger can be set to 26V, 21A).