My neighbor has a computer, how can I pull a network cable by myself? How to connect? How can I conn

After the network cable is pulled from someone else's house, the method of installing the router is as follows:

1. Don't connect the network cable from someone else's home to the router first.

2. Use a network cable to connect any LAN port of the router at one end and the network card of the computer at the other end.

3. Log in to the interface through the computer browser and click LAN port settings.

4. Change the LAN port IP to avoid conflicts with the IP segment of other people's main routers;

5. Click WAN port settings, select the WAN port Internet access mode: dynamic IP connection, 6. Click DHCP server settings to enable DHCP server.

7. Click on the wireless settings, the settings and key under the interface, and it is recommended to add the @ character to the password so that others can not rub the network.

8. Click Save to exit, and the router will automatically restart.

9. The network cable is connected to the WAN port of the router, and the computer can access the Internet at this time.

Or use a mobile phone to set up a router, as long as the mobile phone is wirelessly connected to the router, the settings are the same.

If you negotiate with your neighbor and the other party agrees to share the network with you, you can directly connect a network cable from their router to your home, and then connect the router to the dynamic IP mode to obtain the network.

If the other party has a wireless network, you can use the other party's broadband wirelessly in your home through a wireless router bridging. However, the premise is to know the password of the other party's wireless network.

1. The router can be connected to a desktop computer to share the fun of wireless Internet access. However, after the router must be set up, the desktop needs to enter the username and password to log in to the broadband for the first time, and it can automatically log in to the broadband in the future.

2. Without the router settings, it is impossible for laptops and desktop computers to log in to broadband.

3. If the router is set up successfully, the laptop can also access the Internet wirelessly, but the desktop computer can not access the Internet, that is, there is a problem with the desktop computer system, and it is okay to change to a W8 system or a version of the XP system.

The issue is too broad.

Confirm that the router is connected to the network and can surf the Internet normally (whether there is an account and password with automatic dialing) and confirm that the DHCP of the router is turned on;

Check whether the router has set Internet access restrictions (such as binding MAC addresses, traffic limits, IP address restrictions, etc.);

Make sure that the IP address of the XP computer is set correctly (usually use "automatically obtain IP address"), and finally, make sure that the network cable can be connected normally.

Whether the router can be used normally.

The web page pulled by the other party is connected to the LAN port of the other party's router, the network cable should be plugged into the WAN interface of the subordinate router, and the subordinate router can use dynamic IP mode, taking WR841 as an example, the setting steps are as follows:

1. First confirm whether the LAN port address of the upper-level wired router is, if so, then you must modify the WR841NLAN port address;

3. Open the browser and enter, log in to wr841;

4. Enter the default account password for admin, click OK;

5. Enter the settings page, click Network Parameters - LAN Port Settings, enter the new LAN port IP address on the right, for example, click Save, the router prompts to restart, click Yes;

6. After restarting, enter the browser address bar and log in again;

7. Click WAN port settings, select the WAN port connection type as dynamic IP, and click Save;

8. Click Wireless Settings - Basic Settings on the left navigation;

9. Click to turn on the wireless function, turn on the SSID broadcast, WDS can not be turned on, the key type is recommended to select WPA2-PAK, set the wireless password of more than 8 digits, and click Save.

If you already have a cat in someone else's house, you just need to add the router directly, the router can be split to the computer, and you can set up the router hotspot.

After buying the router, let him set it up, plug in the network cable and it can be used.

If you can't open the router login screen when setting up your router, it is because your computer network card has not been able to get the correct network parameters from the wireless router, such as your router login IP address, then set you.

The IP address of the computer NIC is, the subnet mask is set by default, and the gateway should be.

Connect the computer to the LAN port of Lu Zhengyouyou's device through the network cable, as long as the Qi Zheng router is connected to the mutual lifting of the Huai network, the computer can access the Internet.

Yes, only through a wireless router.