TAG Heuer sapphire surface, how to repair it by scratching, it is said to have a layer coating on it

Treatment: 1. When there are scratches or slight scratches on the watch mirror, you can drop one or two drops of water on the watch mirror, then squeeze a little toothpaste, and then wipe it back and forth with a cotton ball to remove the scratches and make the watch glass as new.

2. If it is serious, you can polish it.

3. Find an official after-sales service center.

If the case and strap have deep pits, use abrasive wheels and felt wheels to remove the dents, and use steel wire wheels for sandblasting (matte effect); General polishing with fast (2800 rpm), sand drawing with slow speed (1400 rpm); If the watch parts are only slightly scratched, the use of polyester cloth wheels has a better effect and higher polishing efficiency.

If there are scratches or slight scratches on the crystal of the watch, you can use toothpaste and then wipe it back and forth with a cotton ball, and in severe cases, you can polish it.

Dispose. Under normal circumstances, there will be a service address on the warranty couper, or find a regular watch service center for processing.

If the watch is dropped to the ground, or if it is bumped, it causes scratches, cracks, broken corners or even complete shattering of the watch. Generally, the first two can also be used exquisitely, but it only affects the aesthetics of the watch, but if it is the latter two, it is necessary to replace the watch mask, that is, the glass on the dial. **You need to take it to the master to check it first, the glass to see the specifications, size, material, the pointer to see the style and movement, the replacement is the original accessories, otherwise the installation can not be.

It doesn't matter if the watch is scratched or worn, but if the watch is completely broken, you should immediately pull out the head and stop the watch, then put the watch flat in reverse, and immediately send it to a regular watch repair center for repair and replacement. Be sure to avoid drastic ** on the way to the destination.

Treatment method of epidermal rupture:

1. Pull out the watch handle and let the watch stop.

2. How to deal with the crackage of the watch? You must not dial the hands or adjust the calendar quickly.

3. The watch should be placed flat (preferably with the watch mask facing down), and the watch should be placed flat until it is sent to the watch repair shop.

4. Do not do violent vibration and shaking during this period.

5. Instruct the watch repair shop to be careful not to let the glass chips hurt the dial and watch hands during disassembly and repair.

It is best to go to a repair shop for repairs.

This can be repaired, and it can be repaired again in the four S store, and there won't be any major problems. If it really can't be repaired, then the only way to replace it is to look at whether this area is relatively large?

Generally speaking, you can go to the 4S shop to re-fix it, which may have a better effect, and you can use it to go to the beauty shop.

Hello, according to the situation you described, you can go to the four S shop to repair it, or go to the car beauty shop to repair it.

The solution to the water in the watch and the fog on the mirror:

Wrap the watch tightly with several layers of toilet paper or flannel cloth that is easy to absorb moisture, and bake it under the light bulb for about 30 minutes to eliminate the water mist inside, but do not put it close to the light bulb or bake it directly, so as not to cause the surface to be deformed by heating.

Wear the surface inwards and the bottom case outwards on your wrist to remove the mist from the surface after a few hours.

If you have silicone, you can put the silicone and the watch in water into a closed container, and after a few hours, take the watch out again, and the water mist in the watch will disappear.

If the water ingress of the watch is serious, it is best to send it to a watch shop to wipe the oil and eliminate the water in the watch to avoid rust on the parts of the watch.

Note: In order to prolong the service life of the watch, you should try to avoid fog and water droplets in the waterproof watch, do not wear the watch when washing your face, bathing, swimming and other "hydrophilic" activities, do not be affected by water vapor and hot vapor, and pay more attention not to be exposed to rain on rainy days.

What to do if the watch gets water.

It is normal for the watch to get water, if the water is not serious, but there is a layer of fog in the watch glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, and bake it for about 30 minutes at a distance of 15 cm from a 40-watt light bulb to eliminate water vapor. Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating. You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours.

Of course, there are also some daily repair methods for watches to get into the water:

1. Dry the granules with silica gel. If water enters the case, you can use a granular substance called silicone to put the watch in an airtight container with the waterlogged watch, and after a few hours, remove the watch and the water will disappear. This method is simple and economical, and there is no damage to the accuracy and longevity of the watch.

The silica gel that has been absorbed many times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used again and again.

2. Bake with a light bulb. If the water ingress is not serious, but there is a layer of fog in the surface glass, then you can use several layers of toilet paper or flannel cloth that is easy to absorb moisture to wrap the watch tightly, and bake it at a distance of 15 cm from a 40-watt light bulb for about 30 minutes to eliminate the moisture. Do not bake the watch mask directly close to the fire, so as not to deform the watch by heating.

3. Wear the watch backwards. You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the moisture can be eliminated after two hours. If the water ingress is severe.

After the watch enters the water and fog, it should be brought to the after-sales service center as soon as possible, and the professional technician will clean the movement for you.

1.Disassemble the whole machine and prepare it for use with the appropriate screwdriver.

2.When removing the screen, gently separate the chiplet that connects the screen to the motherboard from the motherboard.

3.Before removing the metal shielding isolation layer, the network access card and the card slot sticker under the network access card must be torn off.

4.Take a hair dryer and blow dry, not for a long time in front of the screen, such high temperature will destroy the screen.

1.If there is only fog in the glass, you can wrap the table tightly with several layers of toilet paper or flannel cloth that is easy to absorb moisture, and bake it at a distance of 15 cm from a 40-watt light bulb for about 30 minutes to eliminate moisture.

2.Do not bake the watch directly near the heat, so as not to deform the watch by heating.

3.You can also put the mask facing inwards and the bottom shell facing outward, and wear it on the wrist backwards, and the water vapor can be eliminated after two hours.

4.If the water ingress is serious, it should be sent to the watch shop immediately to wipe the oil to remove the moisture from the movement.

It is recommended that you can open the warranty coupon attached to the watch under normal circumstances, and there will be a service address on the warranty copy (B 2606, China Resources Building, Qianjiang Road, Hangzhou), or find a regular watch service center for testing and maintenance of the address of the store, etc., if there is a professional after-sales maintenance center nearby, it is also possible.

A fully automatic mechanical watch relies on the movement of the arm to cause the rotating surface of the rotor to generate energy to support the daily operation of the automatic mechanical watch. Wearing it for more than 8 hours a day can ensure the daily operation of the automatic watch, but it is not absolute, when the power of the fully automatic mechanical watch is insufficient, the watch can be wound to supplement the power of the mechanical watch to support the daily operation.

If the water ingress is not very serious, but there is fog on the watch glass, you can directly wear the watch on the wrist directly, and the best solution is to go to the after-sales center in time, and the maintenance technician will remove all the parts and wipe the oil one by one to ensure that the watch has no possibility of rust. It should be noted here that it is timely, delaying the repair will often delay the best time for Carl F. Bucherer watch maintenance, resulting in damage to the parts.

Shanghai TAG Heuer After-sales Service Center is located in Room 918, 9th Floor, Landmark Plaza, Nanjing East Road Pedestrian Street, Huangpu District, Shanghai. Secondly, the temperature change will affect the viscosity of the lubricating oil, affect the transmission efficiency, and thus affect the timing.

The hairspring and balance wheel can be made of special alloy materials, so that it has a certain temperature compensation in the operating temperature zone, or by moving the temperature of the fast and slow needle.

Hello, glad to answer for you.

Water and fog into the watch has the greatest impact on the watch movement, and it should be dealt with in time to prolong the service life of the watch. If not treated in time, the residual moisture will easily cause the internal movement to oxidize and rust, which will lead to inaccurate watch timekeeping and watch failure.

TAG Heuer Watch Care Center is located in Room 3705, Building 2, Grand Gateway Plaza, No. 3 Hongqiao Road, Xuhui District, Shanghai

If there are scratches or slight scratches on the mirror surface of the watch, you can drop one or two drops of water on the mirror first, then squeeze a little toothpaste to wipe it, and then wipe it back and forth with a cotton ball, you can remove the scratches and make the mirror as new.

Another method is sandpaper wiping. You can choose a piece of sandpaper, try to use relatively clean pliers when taking the sandpaper, and then, use pliers or other tools to clamp the selected sandpaper, find the texture of the glass surface of the watch, and then wipe it gently.

The mirror surface of some watches is easy to scratch, so you should pay attention to maintenance and protection when wearing it to avoid bumps. Minor scratches on the mirror of the watch can be removed by yourself, when the scratches are more serious, or you can't solve them, it is best to take them to a professional watch repair shop to avoid greater losses caused by improper treatment.

TAG Heuer Watch Care Center: 400-659-0877

How can a mechanical watch go too fast.

In fact, when we encounter our mechanical watches going too fast, there is no need to worry. First, let's see if it's caused by magnetization. We can use a compass to tell if the watch is magnetized.

Place the compass on a flat surface, hold the watch close to the compass, quickly swing it back and forth above the compass, and try to change a few directions a few times. Just a roll of the compass is fine, and if it doesn't turn well, it means that the watch is magnetized. However, mechanical watches always go fast, usually oscillating or magnetizing.

If you can't tell it yourself, leave it to a technician to check.

As a pioneer of Swiss watchmaking for 100 years, TAG Heuer has been creating precise timekeeping tools and exquisite watches, and today has two in-house movements and four watchmaking workshops, and has achieved micro blades instead of hairsprings, belts instead of gears, timekeeping accuracy of 5 10,000 seconds, double tourbillon counters, magnetic drives instead of hairsprings, and many other achievements. In 2012, TAG Heuer took precision watchmaking to the next level with its Carrera Mikrogirder with a precision of 5 10,000 seconds, winning the Grand Prix de la Haute Horlogerie de Genève, the Grand Prix de la Haute Horlogerie.

A new silver-blue three-hand watch pays homage to the 1963 Carrera chronograph with a touch of red on the "60" on the dial scale, the iconic TAG Heuer logo and the minute hand.

During the warranty period, it will be sent directly to the counter for maintenance. Shanghai and Beijing are all serviced, you can call ** to consult after-sales maintenance services.

Find a regular watch service center for testing. Avoid greater losses due to improper handling.

How to deal with water ingress into the watch:

If you accidentally get water inside your case, you can use a granular substance called silicone to put it in a meter-closed container with the watch that has accumulated water, and after a few hours, you can remove your watch and the water will disappear. This method is simple, convenient and economical, and does not compromise the accuracy or longevity of the watch. In addition, the silica gel that has absorbed water many times can be dried at 120 degrees for several hours, and the water absorption capacity is renewable, and it can be used again and again.

Second, the secret of refurbishment of the watch with water ingress. If your watch is scratched with a lot of lines, you can drop one or two drops of water on the watch mask, and then squeeze a little toothpaste to wipe it, you can remove the scratches and make the watch mask as new.

How to protect the movement on a day-to-day basis:

The watch should be cleaned regularly and should not be kept in a closet with mothballs to avoid deterioration of the watch oil.

Do not open the back cover of the watch frequently, so that dust does not enter the movement and affect the normal operation of the watch.

It is best to wind the spring at a fixed time every day, not too tightly, otherwise the spring is easy to be stuck by the oil in the barrel, and when the spring is relaxed, it is easy to be broken due to excessive elasticity.

Do not press the button too hard to avoid malfunctioning.

As a kind of precision mechanical object, the various parts inside the movement are connected to each other and generate energy. In the process of operation, the lubricating oil gradually decreases, and the friction of the gears against each other will produce some metal chips, increasing the rotational resistance. On the other hand, even a water-resistant watch with a better sealed case will inevitably block the ingress of dust, dirt, and moisture.

The cost of watch maintenance is popular: the dismantling and cleaning fee of an ordinary watch is 770 yuan, and if it is a gold watch, the dismantling and cleaning fee is more than 800 yuan. According to the regulations of the watch industry association, tens of thousands of yuan of watches, in addition to the dismantling and cleaning fees, should also be charged according to the watch introduction grade** and other inspection fees of one thousandth.

For mechanical watches that are not worn for a long time, they should also be wound regularly to allow the mechanism to rotate. As for quartz watches, their battery life is generally 1 to 2 years, and the battery should be replaced regularly, and the sealing ring should also be replaced when the battery is replaced.