What are the points to look for when reversing into the warehouse on the left?

One. Uphill stop, start.

Exam requirements: It is required to stop at a fixed position on a ramp with a slope of 10% and a length of 30 meters, and the coordination of direction, braking and clutch is examined.

Two. Side parking.

Exam requirements: Compulsory items for C and Z photos. The vehicle is required to move the vehicle into the right storage position without touching and wiping the pile rod of the storage position, and the wheels do not touch the lane edge line and the storage location sideline.

Reference method: 30 cm forward on the right side of the car, stop when the No. 1 pole is seen in the rear window, and there is a horizontal end line at the close distance in front of the car. Be sure to see the boom before and when reversing, the slower the reversing, the better, but you can't stop.

When reversing, hit the left turn signal, when the rear window of the car can not see the No. 1 lever, hit the direction to the right for one and a half circles, look at the left rearview mirror to see the No. 4 lever to the left for one and a half circles, look at the right rearview mirror of the front and see the No. 4 lever to the left for one and a half circles, look at the front of the right rearview mirror and the No. 1 pole overlap the direction to the left to the end of the body to stop at the right time, and then go forward to hit the right turn signal. Pay attention to the situation behind the road, and use the semi-linkage to move forward without the curb line in the direction of turning.

Three. Positive and negative library skills.

Exam Operational Requirements:

Reverse from starting point A to garage B stopping, advance to the return area of starting point C, then reverse into garage B to stop right, advance to end point A (starting point), and the test is completed.

Exam Judging Criteria:

1.The body shall not be out of the red line, otherwise the "body out of the line" is unqualified;

2.Do not stop when reversing or moving forward;

3.After pouring into the warehouse, it needs to be stopped;

4.After the test is completed, hang neutral and get out of the car and exit the test room.

Look at the left and right mirrors and rearview mirrors.

Before reversing, first see the situation behind the car, estimate the route of reversing, determine whether the front of the car will hit obstacles, try not to step on the accelerator when reversing, and control the speed not too fast.

Turn the steering wheel with your left hand according to the direction of travel at the rear of the car: if the rear of the car needs to travel to the rear right, turn the steering wheel to the right; Otherwise, turn the steering wheel to the left. In fact, this is the same as the steering operation when the car is driving forward, so you will not be in a hurry to get in the wrong direction when you keep this in mind.

Do not keep looking at the back of the car during reversing, and on the premise of confirming the safety of the rear of the car, you need to observe the left and right rearview mirrors from time to time, pay attention to the distance between obstacles and the body, and use the steering wheel to correct the position of the car when the car is retreating.

If you feel that the front of the car may hit an obstacle during reversing, you also need to look in front of the car at the appropriate time. Especially in the case of a large rotation amplitude of the steering wheel, because the turning radius of the steering wheel is greater than the turning radius of the rear wheel during the steering process, and the head of the car is thrown outward when reversing, so it is necessary to pay attention to the front of the car to avoid rubbing.

Don't get into the habit of playing the steering wheel on the spot, as it is easier to damage the vehicle and it can be a hassle to fight.

The first point is the point where the steering wheel hits to the right when reversing. The second point of the ruler imitation is when the protrusion of the body in the right source bend is two fingers wide from the right corner of the right corner. The third point is that the right corner in the right rearview mirror points to the middle of the car's front door handle. The following information is relevant:

Reverse warehousing: reversing into storage is a compulsory test for small car driver's license after 2013. Examine the driver's ability to operate the car in the field. Reversing into the garage is one of the test points in the driver's license test. That is, to drive the vehicle correctly into the garage from both sides of the movement.

Subject 2: The second subject, also known as the road test, is a part of the motor vehicle driving license test, and is the abbreviation of the field driving skills test subject. The vehicle's C1 test items include reversing into the garage, side parking, fixed-point parking and ramp start, right-angle turning and cornering (commonly known as S-corner).

Millions of car purchase subsidies.

The right reversing into the garage to see the following three points: 1, the right rear wheel and the location of the corner line: reversing while paying attention to the right side of the rearview mirror, when the rearview mirror sees that the rear wheel of the car is about to overwhelm the corner line of the garage, quickly kill the steering wheel to the right.

2, the distance between the rear wheel and the right corner: observe the distance between the rear wheel and the right corner, if the rear wheel is just 30cm away from the right corner, then there is no need to correct the direction and continue to reverse directly; If the angle between the wheel and the library is less than 30cm, you can keep a distance of about 30cm by turning the steering wheel back to half a circle. 3. Whether the body and the library edge line are parallel:

Pay attention to the rearview mirror, when the body is parallel to the library line, quickly return to the right direction, if the left and right are not equal, according to the principle of "which side is wide, which side hits" fine-tuning.

1. Observe the distance between the rear wheel and the left library angle.

Observe the distance between the rear wheel and the left corner, if the rear wheel is just 30cm away from the left corner, then there is no need to correct the direction, and continue to reverse directly.

2. Observe the rearview mirror.

Pay attention to the rearview mirror, when the body is parallel to the library line, quickly return to the right direction, if the left and right are not equal, according to the principle of "which side is wide, which side hits" fine-tuning.

In the subject 2 exam, when we complete the right reverse car into the garage and come out, we will carry out the left reverse car into the warehouse. In fact, the main point of the left reversing car into the garage and the right reversing car into the garage is about the same, when we are in the left backwards, the car slowly retreats, first to observe the left rearview mirror, and then when the left rear wheel is about to press the edge line of the corner of the library, at this time is the best point to kill the steering wheel to the left, and then wait for the body to almost return to the right, and then quickly return to the right, fine-tune the left and right distance after looking at the parking point, parking is completed.

The specific operation steps of left reversing into the warehouse

The first step, change the reverse gear, reverse while paying attention to the left side mirror, when the rearview mirror sees that the rear left wheel is about to overwhelm the library angle line, quickly kill the steering wheel to the left;

Step 2,Continue to observe the distance between the rear wheel of the car and the left library angle, if the rear wheel of the car is just 30cm away from the left library angle, then there is no need to correct the direction, and the car can continue to reverse backwards;

Step 3,If the angle between the wheel and the library is less than 30cm, you can keep a distance of about 30cm by turning the steering wheel half a circle;

Step 4,Continue to reverse backwards, pay attention to the rearview mirror, when the body is parallel to the library line, quickly return to the right direction, if the left and right are not equal, according to the principle of "which side is wider and which side hits" for fine-tuning;

Step 5,Look at the finish line at the back end of the mirror, and stop when the lower edge of the mirror coincides with the yellow line.

The first is to kill the steering wheel position. When reversing on the big sideline, look at the left rearview mirror, and when its lower edge overlaps with the big white line at the starting point, you should quickly kill the steering wheel. If you turn the library to the right, you will kill the steering wheel to the right; If you turn the library to the left, you will kill the steering wheel to the left.

During the period, it is necessary to control the clutch and maintain an even speed without stopping.

The second is that the rear of the car is close to the corner of the garage 30 centimeters. Wait for the noisy vehicle to continue to retreat, carefully observe through the rearview mirror and control the steering wheel, wait for the distance between the rear of the car and the corner of the garage to be 30 cm, and carry out the half-turn operation of the steering wheel; At this time, the vehicle must continue to maintain a slow backward attitude.

Please click Enter a description.

The third is the parking point. Adjust the direction according to the distance between the body and the edge line of the garage so that the vehicle and the garage are parallel. When the lower edge of the left rearview mirror overlaps with the edge line of the garage, find the parking spot at this time, and then press the clutch and brake to stop the car, so that the "reversing" part of the reversing into the garage is completed.

Please click Enter a description.

The fourth is the outbound point. After the completion of the storage of the next Wu dry operation is out of the warehouse, control the steering wheel to let the body vertically forward, observe the position relationship between the front hood and the opposite garage line, wait for the front cover edge liquid orange edge line and the garage edge line coincide, to the left (or to the right) to kill the steering wheel, you can go out of the warehouse smoothly, at this time the wheel will not be pressed to the corner of the garage.