How do you install the pulleys on the sliding door of your wardrobe?

1. Take a frame and lower seal, and fix it with fixing screws.

2. Place the fixed frame on the ground, and then arrange the sliding door panel on the frame.

3. Take another frame and snap it into the arranged sliding door panel, and fix the lower seal and frame with screws.

4. Snap into the upper seal, fix it with screws, and fix the upper pulley at the same time.

5. After the upper and lower screws are fixed, use the traction screws to fix the slide wheel in the lower seal to complete the installation.

6. Note: When installing the sliding wheel, the pulley shrapnel is inward.

The pulley is stuck in the aluminum alloy lower frame, and there are holes on the side, and the height of the door can be adjusted by adjusting the screws. When installing the door, first put the upper part into the upper rail, and then press (with your hand or paper card) the slide wheel, move into the lower rail, okay, ok

1. When installing the pulley, we must ensure that the size of the track box is about 12 cm high and about 9 cm wide, and the track is installed in the track box, and the height of the sliding door is higher than 1.95 meters to prevent a certain sense of depression.

2. Note that the installation ratio is generally about 80 cm to 200 cm for the installation size of the normal sliding door pulley, which is more stable and looks more beautiful, so the overall width and height match the best proportion.

3. Pay attention to the selection of sliding doors, and do not choose the sliding door from the ground to the top when choosing. Because if you push and pull often, the amplitude is relatively large, so that it will be deformed after a long time, which makes it difficult to open and use it in the later stage.

4. Correctly install the track installation track, first fix the upper track, you can use a pen to draw a fixed surface at both ends of the track, so that the upper track is installed, and then use the perpendicular line to install the lower track to fix it to ensure that it is completely parallel.

The wardrobe pulley is installed as follows:

1. Upper track installation. It is necessary to place the track in the middle of the door sleeve, so carefully measure the dimensions of the 2 sides first.

2. Drill holes after positioning.

3. The two sides are fixed and the hole in the middle is drilled.

4. Install the lower track and wipe it clean first.

5. Then fix the position of the lower rail, and clean the inner layer of the track with a brush.

6. Sliding door installation. First, lift the door gently to let the upper pulley of the door enter the upper track, and then lift the sliding door with one hand, and pull the lower wheel with the other hand, so that the lower wheel can smoothly enter the lower track.

7. The installation of the sliding door is completed, and the next step is to paste the anti-collision strip to protect the sliding door.

8. Complete the renderings.

How to install wardrobe pulleys:

1. Take a frame and lower seal, and fix it with fixing screws.

2. Place the fixed frame on the ground, and then arrange the sliding door panel on the frame.

3. Take another frame and snap it into the arranged sliding door panel, and fix the lower seal and frame with screws.

4. Snap into the upper seal, fix it with screws, and fix the upper pulley at the same time.

5. After the upper and lower screws are fixed, use the traction screws to fix the slide wheel in the lower seal to complete the installation.

6. Note: When installing the sliding wheel, the pulley shrapnel is inward.

Benefits of pulleys:

The key factor that affects the service life of a sliding door is the pulley. The design life of the pulley is about 15 years, and the pulley of the cabinet door is composed of two parts, one is the top wheel and the other is the bottom wheel. There are two ways to install the bottom wheel, one is implicit and the other is external.

Hidden bottom wheel means that the bottom wheel is installed under the door, and after being placed in the guide rail, the wheel cannot be seen from the front and back of the door.

Different wardrobe sliding doors have different designs and installations, some are installed outside the sliding door, and some are installed inside the sliding door frame, which also requires you to buy a pulley suitable for your sliding door.

You have this pulley from **, this you can ask the seller to give you the manual.

The maintenance of the sliding door is mainly the lubrication and rust prevention of the slideway and the small wheel. First of all, clean the slide carefully, apply grease into the slideway and pulley, pull the door several times, the grease will penetrate into the slideway and bearing, and then pull it smoothly.

To use sliding door wheel rail grease, colorless and transparent, good adhesion. , good durability, with safety certification. Tiger head hotolube or Kruber can be, senge and other well-known sliding door brands use this.

There are 130 grams of small tubes in the leopard, which is easy to use. The maintenance interval is half a year.

Do not use engine oil or ordinary grease, the durability is poor, and the smell is very strong, affecting the body.

Summary. Dear, I am glad to answer for you: how to install the sliding door pulley**What is the reason for the return of the wardrobe sliding door after installation?

1. Take a frame and lower seal, and fix it with fixing screws. 2. Place the fixed frame on the ground, and then arrange the sliding door panel on the frame. 3. Take another frame and snap it into the arranged sliding door panel, and fix the lower seal and frame with screws. 4. Snap into the upper seal, fix it with screws, and fix the upper pulley at the same time. 5. After the upper and lower screws are fixed, use the traction screws to fix the slide wheel in the lower seal to complete the installation. 6. Note: When installing the sliding wheel, the pulley shrapnel is inward. Wardrobe Pulley Track Door Installation Details Wardrobe Pulley Track Mounting Accessories:

upper pulley, slide wheel, fixing screw, slide wheel traction screw, etc.; Upper and lower pulley installation position and fixing method. Basically, the installation method of the wardrobe sliding door is the same, but there are also some installation methods that are slightly different because of different designs, it is recommended to install the wardrobe when the wardrobe is installed, and the installation fee can be uniformly given. Thank you for your patience <>

I hope you are satisfied with my service and I wish you all the best again! Peace and joy!

How to install the sliding door pulley**What is the reason for the return of the wardrobe sliding door after installation.

Dear, I'm glad to answer for you: How to install the sliding door pulley**What is the reason for the return of the wardrobe sliding door after installation? 2. Place the fixed frame on the ground, and then arrange the sliding door panel on the frame. 3. Take another frame and snap it into the arranged sliding door panel, and fix the lower seal and frame with screws. 4. Snap into the upper seal, fix it with screws, and fix the upper pulley at the same time. 5. After the upper and lower screws are fixed, use the traction screws to fix the slide wheel in the lower seal to complete the installation. 6. Note:

When installing the slide wheel, the pulley shrapnel is pointed inward. Wardrobe pulley track door installation details Wardrobe pulley track installation accessories: upper pulley, slide wheel, fixing screw, slide wheel traction screw, etc.; Up and down the installation position and fixing method of the slower shroud cover wheel.

Basically, the installation method of the wardrobe sliding door is the same, but there are also some because of the different design of the installation method will be slightly different in the pin cover, it is recommended to install the wardrobe when the wardrobe is installed, and the installation fee can be uniformly paid. Thank you for your patience <>

I hope you are satisfied with my service and I wish you all the best again! Peace and joy!

It is recommended to contact the after-sales party of the wardrobe and ask a professional installer to install it.

<> "First, how to install the wardrobe door pulley.

First of all, determine the installation position, drill holes in the corresponding position, drill holes on both sides, and fix them with screws. Drill a hole in the middle so that the reeds are fixed with a screwdriver. After that, install the lower rail, wipe the surface clean, and put the sliding door into the upper and lower rails.

Adjust the position to move. According to the installation method of the pulley track, drill and fix the track and remember to clean it.

Second, it is better to choose a sliding door or a swing door for the wardrobe.

1. If you are struggling with how to choose whether to push or slide or swing, we can choose according to the indoor space area. If the indoor area is relatively large, you can choose the swing door. But in the process of use, it will be more convenient to use.

When we open the cabinet door, we can see all the clothes inside, and the items can be presented at a glance, and it is much easier to find clothes.

2. We can also install a mirror in the casement wardrobe, and the space of the mirror will not occupy a large place, and its sealing is also very good and it is not easy to fall dust.

3. If you choose a sliding door, its advantages are also very obvious, and it will not take up a lot of indoor space. If it belongs to a small apartment, it is very suitable to choose this kind of sliding door with a code, but its defects are also easy to see. The door can only be opened halfway, so it will be a little more complicated when we are looking for something.

And it is necessary to install a pulley track, which is easy to accumulate dust and even get stuck after long-term use.

When installing a wardrobe in the bedroom, you need to pay attention to the installation track. What are the steps for the installation of sliding wardrobe door slides? PChouse will take you to find out.

1. The size of the track box on the sliding door should be 12 cm high and 9 cm wide. Just like a curtain box, by installing the track inside the track box, you can hang the sliding door on the track. If the height of the door is less than a meter, it can feel oppressive.

Therefore, when making a sliding door, you must ensure that the height is at least 207 cm.

2. Generally speaking, the size of the normal door is about 80 cm to 200 cm, because under this structure, the door will be relatively stable and look more beautiful visually. Therefore, the ratio of width and height of the sliding door should be similar to the ** size.

3. It is best not to use a sliding door (open hanging track box) from the ground to the top. Because the swing amplitude is too large when pushing and pulling, the sliding door is easy to deform after a long time, and the door cannot be opened after deformation, which means that it cannot be repaired and cannot be used.

4. Finally, the track for installing the sliding door. Fix the upper track, then use the gravity cone (hanging line hammer) to hang 3 points at both ends and the midpoint of the upper track, draw the 3-point fixed surface with a grease pen on the ground, and then install the upper track, and then put a hammer to the ground at the center point of the upper track, put the vertical line at both ends of the track, and fix the lower track on these 3 points, so as to ensure that the upper and lower tracks are completely parallel, and the push and pull of the sliding door is in the best state.