Urgent: Why do I have to get back up after my computer has an error and drops to connect 10

There are many reasons for dropping.

A common problem is the network.

and computer problems.

If your internet connection is slow and your network is running at peak in the morning.

That's easy to drop.

Computer problems. You should first check your computer's CPU usage.

Is it high! This is said to be too big.

The operating load of the system is exceeded.

It's easy to drop.

It's dead. Blue screen.

and so on.

Resolution. 1.If your computer is outdated.

It is recommended to change the configuration of the computer.

2.Clean up the inside of the brain of the power-down Zheng stool.

Clean it up with a variety of software.

Problems similar to those on your computer occur.

Generally, some bad review software occupies system resources.

It's OK to clean it up.

I think there are four common reasons for disconnection.

1. Do you use Kaspersky Antivirus or Kaspersky Firewall, or is it similar to Kaspersky's incognito mode function? If yes,Then you just turn off this incognito mode,Don't be incognito on the network, this situation won't occur after stealth,Invisibility sometimes affects BT** speed,There is also P2P network TV。 A reboot of the machine or cat can sometimes do the trick, but it won't solve the problem at all.

The fundamental reason for this situation is that the broadband network you use (such as telecommunications, Netcom, Tietong, etc.) often has to detect your computer, and this situation will occur when the other party cannot detect your computer network card, and when this situation occurs, your network card does not get the IP address at that time, so this situation will occur.

It's not a big problem, though. Generally, this problem is not easy to occur, unless the broadband network you use needs to be adjusted to the network.

2. Check whether there is strong magnetic field interference in the place where the network cable passes.

Third, the cause of static electricity, friction has static electricity, let alone the computer. The computer's computer source conversion and display will produce caution and static electricity, especially the computer's power conversion is in a high-frequency oscillation state of 500kHz is the most culprit of the chassis electrification, find a section of wire, connect it to the ground wire on the power socket, and connect the other end to the iron post on the window sill. You can measure the voltage change of the front and rear chassis, which is not small.

The normal chassis voltage should be around 3 volts (I haven't measured it myself, my friend said, there should be no problem).

Fourth, use ADSL in addition

modem Internet access has certain requirements for the first line, a balance of filial piety is that the line of each joint to be connected, the second is in ADSL

The modem separator cannot be connected to any equipment before, such as: ** extension, anti-theft device, etc. When reconnecting the binding post of the junction box, it is best to wipe the ** wire and the binding post with fine sandpaper, and wrap the ** wire on the binding post a few more times when wiring, and then ask Hui to tighten the screws to ensure good contact.

Remove the first socket at home, use direct wiring, and it is best to use welding when connecting wires and wires, and then wrap them with insulating tape, anyway, you can't connect any equipment before the separator, so as to ensure that the junction box is connected to ADSL

The good line contact between the modem splitters ensures the quality of signal transmission.

You check it in the following ways:

1. If there is a problem with the network card, repair the network card or replace the network card;

2. The cat (or router) has not lost power for a long time, which may cause disconnection. The power can be cut off for a period of time;

3. The aging of the communication line, the aging communication line will definitely cause the attenuation of the data signal and cause interruption;

4. Monitor your system process to see if there is a process that takes up resources in particular, and try several viruses, Trojans, rogue programs, and anti-kill software;

5. Clean up the junk files on your system disk (whether this has any effect on the disconnection, I am not sure yet).