How to design the floor heating of the hotel, who knows the specific steps and ideas, thank you

To do floor heating, we must first find a professional floor heating company according to the maintenance structure of the house, thermal insulation, local limit temperature and other factors to come up with a detailed floor heating configuration plan and.

Secondly, choose high-quality underfloor heating products.

Finally, find a regular underfloor heating company.

In detail, you can go to Wanjia Heating Electric Floor Heating ** to consult--- the design of floor heating is very important, and it is recommended to be cautious.

** Hotel If you want us to help you design it, our company is a professional company with experience in the construction of this area.

1. Make water and electricity at home first.

2. Lay about 2cm of insulation board on the ground.

3. Lay a reflective film on the insulation board.

4. Laying steel wire mesh.

5. When laying pipelines, fix.

6. Doushi concrete leveling.

7. Other decoration projects.

Plastic hoses should be used for underfloor heating, and there should be no joints in the middle.

Underfloor heating can be turned off when not in use. However, it is easy to cause the pipeline to hold the air inside, which will lead to the need to exhaust the gas next time it is used, generally do not do it as much as possible in the short term, the general method is to close the total sluice gate in front of the geothermal water sealer a little smaller, but do not close it all, which can play a role in saving energy and reducing the indoor temperature.

1. Household heating and floor heating shutdown method.

For users who have installed independent heating, the shut-off of the underfloor heating is very simple, we only need to turn off the wall-hung boiler. However, experts remind that floor heating is not easy to open and turn off, which is very gas consuming, and will reduce the service life of the equipment.

Second, the central heating floor heating shutdown method.

1. For northern users of central heating, the shutdown of floor heating is a little more troublesome. Several kinds of heating heat source is generally a community equipped with a special boiler, the area is unified switch, the temperature is also uniformly deployed by the staff, often causes the temperature to be too high, and ordinary users can not turn off the heat source, at this time you can notice that the central heating area is generally equipped with a set of valves.

2. There is a main valve corresponding to the main pipeline, one is the water inlet valve and the other is the return valve. In the design, it is generally closed in the vertical direction with the pipeline, the parallel direction is open, the vertical direction is closed, if the valve is circular, the clockwise rotation is off, and the counterclockwise rotation is open. We had to screw it parallel to the pipe, or turn it clockwise all the way to the end.

3. If the user wants to turn all the pipes of the floor heating at home but is not sure which direction is open and which direction is off, we can turn on and off all the way, and then you can completely turn off the floor heating at home.

4. Another situation is to partially adjust the temperature, then the two main valves do not need to move, and directly adjust the thermostat in each area.

Data Extensions

Floor heating is comfortable, but don't turn the temperature too high, not only waste energy, but also cause dry mouth and other problems. Generally speaking, when the temperature is adjusted to 18-22 degrees, the human body feels warm and scientifically healthy.

There are two rows of valves on the floor heating, one row is the water inlet valve, the other row is the return valve, and each corresponds to a main valve on the main pipeline. In the design is generally perpendicular to the pipe is closed, the parallel direction is open (except for special design), if the user wants to put all the pipes of the floor heating at home and is not sure which direction is open and which direction is off, we can turn off all the way and turn off the floor heating at home.

The steps are roughly as follows: rotate the electric ball valve from a state parallel to the water pipe 90 degrees to a state perpendicular to the water pipe.

This makes it possible to turn off the underfloor plumbing pipes

If you want to turn off the floor heating, you can close the valve at the floor heating valve, and the floor heating water will not go in, but the house will become cooler.

I believe you must know that the control valve of the floor heating at home is in **, that's good, you can open which valve you can open, open all the valves in one direction, okay after an hour of time to touch the upper and lower plastic pipes of the floor heating control valve with your hands, if all are hot is opened, if one is hot and one is cold, then it should be turned off, obediently it's that simple, no need to find any diagram.

There should be a switch when installing, just turn it off.

What are the two pipes at the front of the inlet and return ball valve in your house for? A radiator in parallel with underfloor heating? Are you not heating this year?

You can consider removing the pressure and opening the ball valve to drain the water, so that it will not be frozen in winter, but if the home is not in the northeast, the temperature is rarely a few degrees below zero, so there will be no freezing and cracking.

It is recommended not to do it yourself, find a company that helps you make floor heating. In addition, the floor heating is generally turned on in winter, so that it will not freeze, if you don't use it, you don't need to drain the water, the floor heating is to keep the pressure in the pipe, and the water can't work when it is discharged.

You can consider removing the pressure and opening the ball valve to drain the water, so that it will not be frozen in winter, but if the home is not in the northeast, the temperature is rarely a few degrees below zero, so there will be no freezing and cracking.

After the first gas check-up, it's fine.

Does underfloor heating freeze in winter? No one at home? No matter what, it won't freeze.

Several of our hotels here are using Fisker floor heating modules, and customer feedback is very good.

It can be built with energy-saving and environmentally friendly cellar-type underfloor heating.

1.A large underground space was dug first: the main fire pit and the fire passage, then firmly built with bricks and stone chips, and finally covered with reinforced concrete prefabricated slabs.

This basement-like space seems to be made up of two rectangles, one large and one small. The large cuboid is 3 meters long, 3 meters wide and high, and the small cuboid is long, wide and high. The "main fire pit", which mainly corresponds to the second half of the house, can store a large amount of fuel, and functions as a boiler that generates heat, and is the source of heat energy for the home, and people can stand and walk upright in it.

Connected to the main fire pit is also a total length of 40 meters of "fire tunnel", 12 fire channels are connected, with a total volume of 10 cubic meters, the shape of the shape is curved to the chimney, with the function of emitting smoke and dust, expanding the heat dissipation area.

2.Before winter, as long as 36 cubic meters of waste firewood and grass miscellaneous materials are added at one time, and the more crushed the better, because only in this way will smoke and heat be produced when burning, and there will be no open flame. After igniting it, you can basically ignore it, and you can burn it all winter without extinguishing it, all you have to do is adjust the vents according to the weather changes and control the fire.

In the fields of the countryside, there are straw firewood and grass everywhere in front of and behind the house, and there is no need to worry about the fuel needed for heating.

3.Floor heating keeps the temperature constant at all times. Straw firewood and grass burning does not produce an open flame, the smoke and hot gas produced by the combustion of the main fire pit circulate underground through the fire channel, and the room temperature is kept at 17-21, so that the floor is not hot, which is equivalent to the room temperature in the city building.

The total surface area of the main fire pit and the fire channel is up to square meters, which is equivalent to half of the total area of the house, and the heat source radiates all corners of the house, and the heat dissipation area is large. Because it is underfloor heating, the effect is much better than that of stoves and earth radiators.

4.In the northern part of China, stoves and earth heaters are the main heating methods for farmers to spend the winter. With the decreasing coal resources and the increasing number of coal resources, how farmers can afford expensive heating costs has become a livelihood issue that cannot be ignored at all levels.

Rural areas have inexhaustible waste straw and firewood, cellar type floor heating has the advantages of convenient materials, good use effect, energy conservation and environmental protection, etc., for the local transformation of rural garbage, improve the rural living environment and benefit future generations is of great significance.

The effect is not very good, and it is also troublesome, so it is not recommended to heat it like this.

Is there a drawing, refer to it! Thank you!

This is possible, there are many ways to heat now, and you are talking about one of them.

Use CAD drawing, first draw the plan, and then need to lay the floor heating room or imitate the plane, the interval (the spacing between the floor heating) is set to dismantle, draw the water inlet line and the return line on the line, use straight line drawing, and use the rounded corner command after drawing (there is no right angle for floor heating, it is a fillet bend). Pay attention to the distinction between the backwater and the inlet line, guess the jujube, and use different colors to represent it.

The floor heating thermostat adjusts the room heating temperature by setting and adjusting the hot water temperature in the floor heating pipe, and the room temperature cannot be directly set. Even if you set the temperature in the room, you have to convert the temperature yourself.

If a thermostat is installed on the floor heating pipeline, the appropriate hot water temperature can be adjusted directly according to the actual heating needs.

You can also find the manufacturer's instruction manual, which will have detailed instructions for temperature setting.