Why does the right click menu frequently jump out automatically and follow

Reasons why the right mouse button frequently jumps out:

1. Short circuit caused by water ingress of the mouse;

2. The right mouse button is damaged and cannot be bounced;

3. The "right mouse button" button on the keyboard is stuck and cannot be bounced.

Workaround for mouse issues:

1. Replace the mouse with a new one;

2. Replace the mouse micro switch;

Workaround for keyboard issues:

1. Replace the keyboard with a new one;

2. Clean the dust inside the keyboard so that the key can bounce up normally.

Replacement method: 1. Buy a new micro switch;

2. Use a Phillips screwdriver to disassemble the mouse;

3. Use an electric soldering iron to solder open and remove the broken micro switch;

4. Replace the micro switch with a new one, and use an electric soldering iron and solder to re-solder the micro switch;

5. After installing the mouse, it can be replaced.

There are two types of computer keyboards: ordinary membrane keyboards and mechanical keyboards, and the cleaning methods are different.

Ordinary membrane keyboard (cheaper, generally between dozens and hundreds):

1. Turn over the keyboard, back up, and pat to clean up the clutter;

2. Stubborn stains and mud stains, gently scrape off with a razor blade;

3. Use a hair dryer to clean up surface dust and small debris;

4. Use a clean, damp cloth to scrub the oil clean.

Mechanical keyboard (**higher, generally 300 to 1,000 yuan):

1. Use the key puller to pull out the keycaps;

2. Use a brush to clean up the dust in the keyboard;

3. Put the keycaps in clean water, pour an appropriate amount of detergent, and gently scrub off the dust;

4. The keycaps are placed on the plane sideways and dried naturally;

5. Plug back into each axis of the mechanical keyboard in turn.

u so cute your right mouse button into the stolen goods need to be cleaned up the system thinks you are often pressed the right button press the kind that can't bounce up please gray fruitless It is recommended to change the mouse Pure hardware problem.

First, the driver problem, upgrade the driver. Second, the mouse problem, try it again.

Stuck or click on the last second one in the arrangement icon, you can try again.

The reason why the right-click menu always pops up automatically is caused by a system error, and the specific steps are as follows:

1. First of all, open the Sakura Qixing computer and enter the main interface of the computer.

2. Then find the key indicated in the figure below on the computer keyboard and quietly knock on the ridge to hit it.

3. Finally, the main interface of the computer will be automatically refreshed, and after the refresh is completed, you can find that the problem of always automatically popping up the right-click menu has been solved.

Aging can also cause problems, so it is recommended to restart the computer and change the socket.

3: There is a problem with the driver, it is recommended to go to my computer - management - device manager, find the mouse, right-click the properties, find the driver item, and roll back the driver.

4: If it still hasn't been solved, it may be a problem with the mouse itself, or it may be an encoder.

If something goes wrong, if so, you can buy a weld on it.

5: System problems, it is recommended to reinstall the system.

When using the computer, if you click the left mouse button and it will automatically go down, how to solve it, let's take a look.

1. First, open [Settings] in your computer and click [Devices] on the home page.

2. Then in the device window that opens, click Mouse.

3. Then in the mouse page that opens, click [Other Mouse Options].

4. Then on the page that opens, click the [Mouse Button].

5. Finally, check [Enable Click Lock] and click [OK], and the problem will be solved as shown in the figure below.

This is the mouse macro program

If it's a 3-button mouse that's something else, if it's a 6-button mouse it's a mouse macro

A mechanical mouse is mainly composed of a rolling ball, a roller column, and a grating signal sensor. When you drag the mouse, drive the ball to rotate, and the ball drives the roller to rotate, and the photoelectric pulse signal generated by the grating signal sensor installed at the end of the roller column reflects the displacement change of the mouse in the vertical and horizontal directions, and then controls the movement of the cursor arrow on the screen through the processing and conversion of the computer program.

The original mouse only existed as a technical proof product, and was not actually mass-produced. After the mouse was officially introduced into the PC, the corresponding technology was also revolutionized. The principle of relying on different resistors for positioning has been completely abandoned, and it has been replaced by a "mechanical mouse" with pure digital technology.

Precautions for use:

Caution should be taken when using the mouse for operation, incorrect use will damage the mouse, the following points should be paid attention to when using the mouse:

Avoid using the mouse on surfaces with a low finish, such as clothing, newspapers, carpets, rough wood, etc.;

It is forbidden to bump the mouse;

The mouse should not be moved in the box;

It is forbidden to use the mouse in high temperature and bright light;

It is forbidden to put the mouse in liquid;

Do not disassemble without permission;

Do not put it in your mouth to bite;

This is the mouse macro program,PUBG automatic pressure gun is like this,It's not the problem of the mouse itself or the driver you said at all.,If it's a 3-button mouse, it should be something else.,If it's a 6-button mouse, that's a mouse macro.。

Plug and unplug the mouse again, it is estimated that the mouse hardware is aging, change it, after all, a mouse, it is inevitable to enter the dust during use. Also, whether the mouse pad is clean or not.

It means that there is a problem with the mouse, it's time to replace it, the mouse has been used for a while, and the sensitivity will have this problem that is not easy to use, and the same is true for big brand mice, and a mouse will be used for about a year.

Haven't you seen the pressure gun macro above? This is obviously the mouse is equipped with a pressure gun macro to become like this.,Is the landlord a computer used in an Internet café? If not, ask the store that sold you a mouse or a friend who has recently used your mouse.

Clean the underside of the mouse, it may be a problem with the mouse pad, rule it out.

A thumb click on the side button of the mouse is good to go.

The mouse is broken, change it again.

Is this the case with a different mouse?

Delete the contents of the context menu First, click the "Run" command in the "Start" menu to open the "Run" dialog box, enter "regedit" in the "Open" field, and then press "OK". Then in the "Registry" window that opens, open the hkey current user software Microsoft Internet Explorer Menuext primary key, there will be many sub-primary keys under the primary key, the names of these sub-primary keys are the commands displayed in the context menu, just find the primary key entry that displays the command, right-click, and select "Delete" in the pop-up shortcut menu.

The specific steps are as follows:

The materials that need to be prepared are: computer,

Take win7 as an example:

1. First of all, you need to open the faulty computer and enter the computer desktop.

2. Then find a rectangle with three bars in the middle of the rectangle button below the full stop button on the computer keyboard and press it.

3. Then the computer desktop will refresh it, and the right-click menu will not automatically pop up after it ends.

I had the same problem with my computer, and then I found out that it was a keyboard problem! It's just that the menu key on the keyboard is broken, so the right-click menu keeps popping up automatically!

Two solutions:

1.After-sales.

2.Block the menu key on the keyboard.,There's a software called "Super Bunny".,That's what I used to solve it!

Let's change the mouse, maybe it's connected to the power.